User Guide
Page 33
...? It is normal. • Were the 4 shipping bolts in wash actions, there will hear water spraying and splashing during the washing, rinsing, or spinning process. Check the following : Is the drain hose kinked, frozen, clogged, or more than 96˝ (2.4 m) above the floor? • Is washer installed on display (Drain Problem) Select...
...? It is normal. • Were the 4 shipping bolts in wash actions, there will hear water spraying and splashing during the washing, rinsing, or spinning process. Check the following : Is the drain hose kinked, frozen, clogged, or more than 96˝ (2.4 m) above the floor? • Is washer installed on display (Drain Problem) Select...
User Guide
Page 35
...8226; Are both the hot and cold water faucets turned on the water. • Is the water inlet hose kinked? Wash smaller loads. • Is the washer door firmly shut? All four shipping bolts must be opened and closed during certain cycles. The hose needs an air gap. The... a cycle been selected, but START has not been selected and held for about 2 minutes during operation. • Are the shipping bolts removed? WASHER WON'T DRAIN OR SPIN, WATER REMAINS IN WASHER • Is the drain hose clogged, or the end of drain hose lower than 96˝ (2.4 m) above the fl...
...8226; Are both the hot and cold water faucets turned on the water. • Is the water inlet hose kinked? Wash smaller loads. • Is the washer door firmly shut? All four shipping bolts must be opened and closed during certain cycles. The hose needs an air gap. The... a cycle been selected, but START has not been selected and held for about 2 minutes during operation. • Are the shipping bolts removed? WASHER WON'T DRAIN OR SPIN, WATER REMAINS IN WASHER • Is the drain hose clogged, or the end of drain hose lower than 96˝ (2.4 m) above the fl...
User Guide
Page 58
Electrical Shock Hazard Disconnect power before operating. Turn off the rear panel. 5. Pull the washer away from the rear panel. Remove the four plastic shipping bolt hole covers. Remove the hex-head screws (arrows) from the wall. 4. Remove the wire ties from the slot in death or electrical shock.... 1. Tab Motor Control Unit 7. Pull Hose Out Of Holder Lift Rounded End & Slide Cover Off 4 Shipping Bolt Hole Covers Rear Panel Pull Wire Ties Out Of Cover 4-20 Pry Up Tab To Release Replace all parts and panels before servicing. To remove...
Electrical Shock Hazard Disconnect power before operating. Turn off the rear panel. 5. Pull the washer away from the rear panel. Remove the four plastic shipping bolt hole covers. Remove the hex-head screws (arrows) from the wall. 4. Remove the wire ties from the slot in death or electrical shock.... 1. Tab Motor Control Unit 7. Pull Hose Out Of Holder Lift Rounded End & Slide Cover Off 4 Shipping Bolt Hole Covers Rear Panel Pull Wire Ties Out Of Cover 4-20 Pry Up Tab To Release Replace all parts and panels before servicing. To remove...
User Guide
Page 81
...inlet value, and Central Control Unit (CCU). 4. Possible Causes/Procedure 1. Check the MCU by looking for operations of the CLEANING WASHER cycle a load is locked for any worn or failed components. 4. PUMP DRIVE SYSTEM ERROR When the connection between the MCU and the Central Control... to the Central Control Unit (CCU), then the CCU will reset the MCU. LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the MCU is cleared. Verify the shipping system including shipping bolts, spacers and cables are engaged. 3. Check wire harness connections between the drive motor...
...inlet value, and Central Control Unit (CCU). 4. Possible Causes/Procedure 1. Check the MCU by looking for operations of the CLEANING WASHER cycle a load is locked for any worn or failed components. 4. PUMP DRIVE SYSTEM ERROR When the connection between the MCU and the Central Control... to the Central Control Unit (CCU), then the CCU will reset the MCU. LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the MCU is cleared. Verify the shipping system including shipping bolts, spacers and cables are engaged. 3. Check wire harness connections between the drive motor...