English Manual
Page 2
Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly. 2 TABLE OF CONTENTS IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 14 WEIGHT RESISTANCE CHART 16 TROUBLESHOOTING AND MAINTENANCE 17 CABLE DIAGRAM 18 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to the center of this manual.
Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly. 2 TABLE OF CONTENTS IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 14 WEIGHT RESISTANCE CHART 16 TROUBLESHOOTING AND MAINTENANCE 17 CABLE DIAGRAM 18 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to the center of this manual.
English Manual
Page 8
... the Left Arm (47) onto the left axle on each Arm. Locate the Short Cable (58). Make sure that the Cable Trap is on the Retainers bend toward the Cover 55 Cap, as shown. 42 21...manner. 70 Cable Assembly 9. Attach the Pulley and a Cable Trap (66) to the bracket with the Left Arm. Make sure that the Cable is behind the indicated bracket on the Top Frame (55). Lay the Cable in place ...indicated side of the Left Arm is routed around a 3 1/2" Pulley 10 (15). Route the Short Cable (58) around the Pulley as shown in the inset drawing. 44 69 45 Attach the Right Arm...
... the Left Arm (47) onto the left axle on each Arm. Locate the Short Cable (58). Make sure that the Cable Trap is on the Retainers bend toward the Cover 55 Cap, as shown. 42 21...manner. 70 Cable Assembly 9. Attach the Pulley and a Cable Trap (66) to the bracket with the Left Arm. Make sure that the Cable is behind the indicated bracket on the Top Frame (55). Lay the Cable in place ...indicated side of the Left Arm is routed around a 3 1/2" Pulley 10 (15). Route the Short Cable (58) around the Pulley as shown in the inset drawing. 44 69 45 Attach the Right Arm...
English Manual
Page 11
... bracket (67) with the 5/16" x 1 3/4" Bolt (72) and a 3 67 5/16" Nylon Locknut (3). 72 10 63 2 23 2 67 Seat Assembly 21 21. Remove the indicated 3 1/2" Pulley (15) from the Top Frame (55). 19 Route the Long Cable (23) around the 3 1/2" Pulley (15) and reattach it should be threaded onto the end of the...) to the Front Upright (42) with the 3/8" x 2" Bolt (12) and the 3/8" Nylon Locknut (21). Make sure that the Cable is in the groove of turns, as shown. 23 Attach the Small "U"-bracket (67) to the bracket on the Top Frame (55) with two 1/4" x 2 1/2" Screws (...
... bracket (67) with the 5/16" x 1 3/4" Bolt (72) and a 3 67 5/16" Nylon Locknut (3). 72 10 63 2 23 2 67 Seat Assembly 21 21. Remove the indicated 3 1/2" Pulley (15) from the Top Frame (55). 19 Route the Long Cable (23) around the 3 1/2" Pulley (15) and reattach it should be threaded onto the end of the...) to the Front Upright (42) with the 3/8" x 2" Bolt (12) and the 3/8" Nylon Locknut (21). Make sure that the Cable is in the groove of turns, as shown. 23 Attach the Small "U"-bracket (67) to the bracket on the Top Frame (55) with two 1/4" x 2 1/2" Screws (...
English Manual
Page 18
the starting and ending points of the Long Cable (23) and the Short Cable (58). If the Cables have been assembled correctly. CABLE DIAGRAM The cable diagram below shows the proper routing of each Cable; Make sure that the two Cables and the cable traps have not been correctly routed, the weight system will not function properly and damage may...
the starting and ending points of the Long Cable (23) and the Short Cable (58). If the Cables have been assembled correctly. CABLE DIAGRAM The cable diagram below shows the proper routing of each Cable; Make sure that the two Cables and the cable traps have not been correctly routed, the weight system will not function properly and damage may...