Weider 8510 Support and Manuals
Get Help and Manuals for this Weider item
Popular Weider 8510 Manual Pages
User Manual - Page 1
.... PATENT PENDING
r
IO
0
OO OO
0
USER'S MANUAL Save this manual
or -ftfture reference. CUSTOMER HOT LINE:
1-800-225-0653
Mon.-Fri., 6 a.m.-6 p.m.
If you have questions, or find that there are committed to you complete satisfaction through direct assistance from our factory. MST
u C
gRavead al[ ecaUtionsrond instruct
Means
&otanu,tg, efore using
s Utpment.
The...
User Manual - Page 2
... purpose is limited in its authorized service centers. This warranty gives you . TABLE OF CONTENTS
LIMITED WARRANTY IMPORTANT PRECAUTIONS BEFORE YOU BEGIN ASSEMBLY HOW TO USE THE HOME GYM SYSTEM TROUBLE-SHOOTING AND MAINTENANCE CABLE DIAGRAM PART LIST EXPLODED DRAWING ORDERING REPLACEMENT PARTS
2 3 4 5 14 16 17 18 19 Back Cover
Note: A PART IDENTIFICATION CHART is attached to the center of...
User Manual - Page 3
... tip.
Inspect and tighten all of the pulleys.
10. Always disconnect the tat bar from movie parts.
3. Use the home gym system only on all parts often. Replace any time white
mg an exercise that the cables are raised.The weights will fall with -pre-existing health problems Read all instructions in this manual and in
the accompanying literatUre before using the...
User Manual - Page 4
...of this manual carefully before calling. For your cardiovascular system, the WEIDER® 8510 will help us assist you for selecting the versatile WEIDER® 8510 Home Gym System.
Service Department toll-free at 1-800-225-0653, Monday through Friday, 6 a.m.
Length: 53 in. The WEIDER® 8510 offers a selection of weight stations designed to achieve the specific results...
User Manual - Page 5
....
• As you assemble the WEIDER 8510, be sure that all parts are oriented as shown in the drawings.
• Tighten all parts of the WEIDER 8510 in the center of
the bracket on the side shown.
Insert two 5/16" x 2 3/4" Carriage Bolts (14)
up through the Stabilizer (5). The high side of this manual. ASSEMBLY
Before beginning assembly, carefully read and...
User Manual - Page 6
...3.
Hand-tighten a 5/16"
2
Nylon Locknut (3) onto each
end of the
Li._
crossbar.
Stack six Weights (25) onto the Weight Bumpers (19). Set two Weight Bumpers (19) onto the bracket on top.
4 1
3 11
27Nisi
11
8
44
55
... each Carriage Bolt. Tighten all on the same side and that the "weider" logo is on the Base (4) as shown. 2. Press a 2" Square Inner Cap (27) ...
User Manual - Page 7
... of the indicated tube in the Top
Weight. Slide the Press Frame into the stack of Weights. Set the Top Weight (76) onto the
stack of Weights (25). Note: This will be a tight fit. Be
sure that the pins on the Weight Tube are sitting
in the pin grooves in the Weight Guides
are on the Press Frame (17).
>- Lubricate...
User Manual - Page 9
... (7) and the 3/8" Nylon Locknut
(not shown).
< 12.
Route the Long Cable (23) around a "V"-Pulley (6). Be sure that the Cable is in the groove of the Pulley and that the Long Cable Trap (50) is turned to hold the Cable in place. Route the Long Cable (23) around the 3 1/2" Pulley (15) attached to the CABLE DIAGRAM on the Left Arm (47). Be sure...
User Manual - Page 10
... Small "U"-Bracket (67) to the lower hole in the Press Frame (17). Route the Short Cable (58) under the 3 1/2"
Pulley (15) attached to the Weight Tube (63) with the 5/16" x 1 1/2" Bolt (72) and a...part identifi-
I
21
15. Route the Short Cable (58) around the 3 1/2"
14
Pulley (15) attached to hold the Cable in place and that the Cable and Pulley move smoothly. Attach the Long Cable...
User Manual - Page 11
... the Seat Frame (36).
Insert the 1/4" x 2" Carriage Bolt (38) through the center hole in the "3 o'clock" position and
that the Cable •
0:1
Trap (not shown) is routed around the 3 1/2"
Pulley (15) attached to the upper hole in the Front Upright (42). Do not completely tighten the Nut. It should be threaded onto the...
User Manual - Page 13
... HOME GYM SYSTEM, beginning on page 14 of the remaining parts will be damaged when heavy weight is any slack in the cables, the cables should be sure that all parts have been properly tightened. See the CABLE DIAGRAM on page 16.
13 Make sure that the cables move smoothly, find and correct the -problem. Use of this manual for proper cable routing. See TROUBLE...
User Manual - Page 14
... at each exercise station may vary from 6.5 pounds to the Long Cable (23) with two Cable Clips. Adjust the length of 12.5 pounds. ATTACHING THE LAT BAR OR NYLON STRAP TO THE LOW PULLEY STATION
Attach the Lat Bar (54) to see how the home gym system should be set up for each part of the weight stack, insert a Weight Pin...
User Manual - Page 15
...Cable Clip.
40
36
13
14 Pin
0
52 0
29
35
53 0 58
WEIGHT RESISTANCE CHART
This chart shows the approximate weight resistance at each butterfly arm
WEIGHT PLATES
PRESS ARM (lbs.)
BUTTERFLY ARM (lbs.)
LEG LEVER HIGH PULLEY LOW PULLEY...leg lever. The butterfly arm resistance listed is not attached to the 6.5 ...weight plates. ATTACHING AND REMOVING THE SEAT
Set the bracket on the ...
User Manual - Page 16
... Long "U"-Bracket
(57) (see drawing 2). Remove the 3/8" Nylon Locknut
(21) and the 3/8" x 2" Bolt (12) from the cables by moving the 3 1/2"
Pulley (15) to slip off the
weight stack.
2
Additional slack can be replaced, see ORDERING REPLACEMENT PARTS on the home
gym system, can be inserted under the middle
weight before resistance is slack in the proper
position and that the...
User Manual - Page 17
... routed, the home gym system will not function properly and damage may occur. If the cables have been assembled correctly. The starting and ending points for each cable are labeled. CABLE DIAGRAM
The cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). The numbers show the correct route for each cable.
2 7
0
5
3 4
Long Cable (23)
-High Pulley...
Weider 8510 Reviews
We have not received any reviews for Weider yet.