Weider Club 16.6st Support and Manuals
Get Help and Manuals for this Weider item
View All Support Options Below
Free Weider Club 16.6st manuals!
Problems with Weider Club 16.6st?
Ask a Question
Free Weider Club 16.6st manuals!
Problems with Weider Club 16.6st?
Ask a Question
Popular Weider Club 16.6st Manual Pages
English Manual - Page 1
....-Fri., 6 a.m.-6 p.m.
USER'S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS? Write the serial number in the center of charge to providing complete customer satisfaction. TABLE OF CONTENTS
IMPORTANT PRECAUTIONS 2 BEFORE YOU BEGIN 3 ASSEMBLY 4 ADJUSTMENTS 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING AND MAINTENANCE 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover...
English Manual - Page 2
... cables bind while you are exercising, stop immediately and begin cooling down.
18. The weights will fall with pre-existing health problems.
Read all parts are on it.
17. Warning Decal 1
• Keep clear of 35 or persons with great force. Do not use only. Make sure all instructions before kneeling on the assist...
English Manual - Page 3
... 1 Dip Handles
Assist Arm Weight Stacks Weight Pin
ASSEMBLED DIMENSIONS: Height: 78 in .
If you for selecting the versatile CLUB WEIDER® 16.6ST weight system. BEFORE YOU BEGIN
Thank you have additional
below and familiarize yourself with the labeled parts. until 6 p.m. For your goal is WESY49202. Length: 92 in. Whether your benefit, read this...
English Manual - Page 4
...stage.
• For help identifying the small parts used in assembly, use the PART IDENTIFICATION CHART located in the center of the weight system in a...parts as grease or petroleum jelly,
and soapy water will be needed. If a part is broken into the Base (4). Assembly will also be more convenient if you have the following information and instructions:
• Place all parts of this manual...
English Manual - Page 6
... Upright (56) with two M8 x 70mm Bolts (11) and two M8 Nylon Locknuts (3). Set two Weight Bumpers (19) on the bracket on the Base (4). Do not tighten the Nylon Locknuts...tighten the M8 Nylon Locknuts (3) yet.
55
11
113
8
44
3 44 Crossbar
3
56
42
74
FRAME ASSEMBLY
5. Set two Weight Bumpers (19) on the bracket on the Stabilizer (5). 4.
Make sure the flat side of Weights (25)...
English Manual - Page 8
Locate and open the parts...; Attach the Leg Press Plate to the Base (4) with a set of holes in each
11
welded spacer on the side shown. ...side
Lubricate
59
21
Welded Spacers
90
8 the Plastic
Bushings should fit snugly over the ends of the Leg Press 10 Arm (96... the Nylon Locknut;
Attach the upper ends of the Long Weight Guides (62) to the Top Frame (55) with the Bolt and...
English Manual - Page 11
...ball is on pages 26-27 of this section, fully unwind the four Cables. Before beginning this manual to the CABLE DIAGRAMS on the indicated side of the Pulley and that the end of each ... Dip Arm (78), and onto the Right Dip Arm (79) in the same manner. Locate and open the pulley bag and the parts bags labeled "CABLE ASSEMBLY."
18
During steps 19 through 39, refer to verify proper cable ...
English Manual - Page 21
... the cables move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be explained in the cables, you will need to remove it to make sure that all parts have been properly tightened. SEAT ASSEMBLY
CLUB WEIDER 16.6ST
47.
See TROUBLE-SHOOTING AND MAINTENANCE on pages 26 and 27 of...
English Manual - Page 22
... to the exercise guide accompanying this manual to the High Cable (58) with a Cable Clip (53). To change the weight setting of either ...CHART on
page 24 to be
changed from the weight
setting.
The Nylon Strap (39) can be adjusted. ADJUSTMENTS
The instructions below describe how each part of the weight system can be attached in the correct starting position for each exercise...
English Manual - Page 23
...Upright (42). Attach one end of the Chain to the front upright (see ATTACHING AND REMOVING THE SEAT above). For some exercises, the Seat (13) must be attached to the M10 x 50mm Eyebolt (35) with the M8 x 70mm Carriage Bolt...the holes in the Leg Press Arm (96). ATTACHING AND REMOVING THE SEAT
To attach the Seat (13), set of holes in the Leg Press Arm.
40 36 13
42 14
Pin
53 52
29
35
53 23...
English Manual - Page 25
...TROUBLESHOOTING AND MAINTENANCE
Make sure all parts are properly tightened each time you use solvents. Re-attach the Bolt, the Washer, the end of this manual.
25 If the cables need to be moved to be replaced, see ORDERING REPLACEMENT PARTS... hole in the Rear Seat Frame (100). Remove the cable and re-install it may have become twisted. The weight system can be tightened. Remove the...
English Manual - Page 28
PART IDENTIFICATION CHART-Model No. WESY49202 R0103A
M10 Nylon Locknut (21) M8 Nylon Locknut (3) M6 Nylon Locknut (2)
M10 Washer (9)
M8 Washer (8) M6 Washer (10) M4 x 16mm Selftapping Screw (87)
...
English Manual - Page 31
...1
10
2
2
3
42
4
1
5
1
6
1
7
1
8
12
9
10
10
11
11
12
12
5
13
2
14
1
15
14
16
1
17
1
18
6
19
4
20
1
21
25
22
4
23
1
24
2
25
18
26
2
27
8
28
2
29
1
30
4
31... Cap M6 x 70mm Screw User's Manual Exercise Guide Greaes Packet
Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST-Model No.
English Manual - Page 32
...
66 15
2 33
21
30 34 35
29
34
66
30
83 44
28 46 21
6
34 30
9 32
3
49
22
46
17
21 27
16
9 88
3
15
66
15
7 23
21 59
90
EXPLODED DRAWING...
English Manual - Page 33
To help us assist you . The MODEL NUMBER of the product (CLUB WEIDER® 16.6ST weight system)
3. LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this warranty is limited to replacing or repairing, at 1-800-999-3756, Monday through one of purchase. All repairs for a period of ninety (90) days from the date of its scope and duration to...
Weider Club 16.6st Reviews
We have not received any reviews for Weider yet.