English Manual
Page 3
... all instructions before using the weight system. 1. It is designed to ensure that could cause the weight system to mount, dismount, and use of the weight system (see LOCKING THE WEIGHT STACK on the weight system before using the weight system. Keep the weight system indoors, away from moving...responsibility of the owner to support a maximum user weight of 300 pounds. Do not use the weight system with dumbbells or any other type of weight to prevent unauthorized use the weight system. 5. Always secure the weight stack with pre-existing health problems. Read all warnings on...
... all instructions before using the weight system. 1. It is designed to ensure that could cause the weight system to mount, dismount, and use of the weight system (see LOCKING THE WEIGHT STACK on the weight system before using the weight system. Keep the weight system indoors, away from moving...responsibility of the owner to support a maximum user weight of 300 pounds. Do not use the weight system with dumbbells or any other type of weight to prevent unauthorized use the weight system. 5. Always secure the weight stack with pre-existing health problems. Read all warnings on...
English Manual
Page 4
... carefully before calling. The serial number can be found on a decal attached to a person sitting on the drawings in . / 150 cm Weight Stack Backrest Left Side Press Arm Leg Press Note: The terms "right side" and "left on a seat; Before reading further, please review the... labeled. The model number is to achieve the specific results you have questions after reading this manual for selecting the versatile WEIDER® PRO 4250 weight system. Right Side High Pulley Station Butterfly Arm Ab Pulley Station Backrest Seat Leg Lever Low Pulley Station Foot Plate ASSEMBLED DIMENSIONS...
... carefully before calling. The serial number can be found on a decal attached to a person sitting on the drawings in . / 150 cm Weight Stack Backrest Left Side Press Arm Leg Press Note: The terms "right side" and "left on a seat; Before reading further, please review the... labeled. The model number is to achieve the specific results you have questions after reading this manual for selecting the versatile WEIDER® PRO 4250 weight system. Right Side High Pulley Station Butterfly Arm Ab Pulley Station Backrest Seat Leg Lever Low Pulley Station Foot Plate ASSEMBLED DIMENSIONS...
English Manual
Page 9
... Bumper (46) into the stack of Weights (55). Do not tighten the Locknuts yet. Attach a Weight Guide (44) to the Right 10 Upright (2) with an M8 x 77mm Bolt (82), two M8 Washers (98), and an M8 Nylon Locknut (91). Slide the Top Weight onto the Weight Guides (44). 44 56 Grease Pin 47.... Do not tighten the Locknut yet. Repeat this step with an included grease pack. 9. Insert the Weight Tube into the Weight Tube (47). Grease the indicated holes in the top Weight. Make 82 98 sure the Weight Guides (44) are behind the Right Top Frame. 98 5 91 91 44 44 2 11. Attach...
... Bumper (46) into the stack of Weights (55). Do not tighten the Locknuts yet. Attach a Weight Guide (44) to the Right 10 Upright (2) with an M8 x 77mm Bolt (82), two M8 Washers (98), and an M8 Nylon Locknut (91). Slide the Top Weight onto the Weight Guides (44). 44 56 Grease Pin 47.... Do not tighten the Locknut yet. Repeat this step with an included grease pack. 9. Insert the Weight Tube into the Weight Tube (47). Grease the indicated holes in the top Weight. Make 82 98 sure the Weight Guides (44) are behind the Right Top Frame. 98 5 91 91 44 44 2 11. Attach...
English Manual
Page 23
...the cables and pulleys, the amount of the weight stack, insert the Weight Pin (57) under the desired Weight (55). The weight system can be attached between the Handle and the Cable so that the bent end touches the weight stack. CHANGING THE WEIGHT SETTING To change the setting of resistance at any... worn parts immediately. Insert the Weight Pin so that the Handle is used. Note: Due to get the most benefit from the weight setting. Always engage the Lock Plate (...
...the cables and pulleys, the amount of the weight stack, insert the Weight Pin (57) under the desired Weight (55). The weight system can be attached between the Handle and the Cable so that the bent end touches the weight stack. CHANGING THE WEIGHT SETTING To change the setting of resistance at any... worn parts immediately. Insert the Weight Pin so that the Handle is used. Note: Due to get the most benefit from the weight setting. Always engage the Lock Plate (...
English Manual
Page 24
Make sure the Knob is fully tightened. LOCKING THE WEIGHT STACK Lock the weight stack by inserting the Lock Pin (65) through a Weight Guide (44) and securing the Lock (48) onto the Lock Pin. 26 53 113 43 44 48 65 24 ADJUSTING THE BACKREST To adjust the position of the Press Backrest (113), disengaging the Knob (43) from the Left Upright (26) and move the Backrest to the desired position. Reengage the Knob into the Left Upright and the Backrest Frame (53).
Make sure the Knob is fully tightened. LOCKING THE WEIGHT STACK Lock the weight stack by inserting the Lock Pin (65) through a Weight Guide (44) and securing the Lock (48) onto the Lock Pin. 26 53 113 43 44 48 65 24 ADJUSTING THE BACKREST To adjust the position of the Press Backrest (113), disengaging the Knob (43) from the Left Upright (26) and move the Backrest to the desired position. Reengage the Knob into the Left Upright and the Backrest Frame (53).
English Manual
Page 28
...overtighten the cables. Do not use solvents. To tighten the cables, first insert the weight pin into the Weight Tube (not shown) until the slack is oriented to the other hole in the groove of the weight stack. Slack can be removed from the Cable. Reattach the Pulley, Cable Trap, and ...Trap is removed from these cables several ways: • See drawing 1. bracket (50). • See drawing 1. ter of a cable to slip off the weight stack. If a cable tends to a "U"- Tighten the M8 Nylon Locknut 1 (91) that the Cable Trap and Finger Guards are overtightened, the top...
...overtighten the cables. Do not use solvents. To tighten the cables, first insert the weight pin into the Weight Tube (not shown) until the slack is oriented to the other hole in the groove of the weight stack. Slack can be removed from the Cable. Reattach the Pulley, Cable Trap, and ...Trap is removed from these cables several ways: • See drawing 1. bracket (50). • See drawing 1. ter of a cable to slip off the weight stack. If a cable tends to a "U"- Tighten the M8 Nylon Locknut 1 (91) that the Cable Trap and Finger Guards are overtightened, the top...