Weider Pro 120 Bench Support and Manuals
Get Help and Manuals for this Weider item
View All Support Options Below
Free Weider Pro 120 Bench manuals!
Problems with Weider Pro 120 Bench?
Ask a Question
Free Weider Pro 120 Bench manuals!
Problems with Weider Pro 120 Bench?
Ask a Question
Popular Weider Pro 120 Bench Manual Pages
Uk Manual - Page 1
... bench)
QUESTIONS? Keep this equipment. Model No. WEEVBE7023.0 Serial No. If you have questions, or if there are missing parts, please contact us: Call: 08457 089 009 From Ireland: 00 (44) 53 9236102 Website: www.iconsupport.eu E-mail: [email protected] Write: ICON Health & Fitness, Ltd. Write the serial number in this manual before...
Uk Manual - Page 2
WEIDER is missing or illegible, see the front cover of ICON IP, Inc.
2 If a decal is a registered trademark of this manual and request a free replacement decal. Note: The decal(s) may not be shown at actual size. TABLE OF CONTENTS
WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 PART IDENTIFICATION CHART 5 ASSEMBLY 6 ADJUSTMENT 9 PART LIST 10 EXPLODED...
Uk Manual - Page 3
...times.
8.
Read all instructions in this manual and all warnings on your weight bench before using the weight bench. Before beginning any worn parts immediately.
3 This is the responsibility of the owner to protect the floor or carpet. Keep the weight bench indoors, away from moving parts.
9. Place the weight bench on a level surface, with pre-existing health problems.
2. If you...
Uk Manual - Page 4
... groups of the body. The weight bench offers a selection of exercises designed to achieve the specific results you have questions after
reading this manual, please see the front cover of this manual carefully before contacting us assist you, note the product model number and serial number before using the weight bench. To help you for selecting the WEIDER® PRO 120 weight bench.
Uk Manual - Page 5
IMPORTANT: If you identify the small parts used in assembly. M6 x 16mm Screw (5)
M6 x 48mm Screw (4)
M10 x 70mm Bolt (14)
M10 Locknut (...the hardware kit, check to the key number of the part from the PART LIST near the end of this manual. PART IDENTIFICATION CHART
This chart is provided to help you cannot find a part in parentheses below each part refers to see if it has been preassembled.
Uk Manual - Page 6
...enough clearance to the Frame (1) with the upper adjustment holes in the Adjustment Leg (3). Press the 38mm
1
Square Inner Cap (16) into the
Adjustment Leg (3).
8
Align the ... small parts, use the PART IDENTIFICATION CHART on page 5.
• The following information and instructions:
• Assembly requires two persons.
• Because of its weight and size, the weight bench should ...
Uk Manual - Page 7
... (1) with the middle adjustment hole in the Frame (1).
2 9
1
Align these holes
13 15
2 14
9
3.
Slide the Foam Pads (6) onto the Pad Tubes (10).
3
6
7 10
6
7
3
10
7 6
7 6
7 Press the 3/4" Round Inner Caps (7) into the Adjustment Leg (3).
Insert the Pad Tubes (10) into the ends of the Pad Tubes (10...
Uk Manual - Page 8
4. Make sure that all remaining parts will be explained in ADJUSTMENT, beginning on page 9.
8 The use of all parts are properly tightened before you use the weight bench. Attach the Bench (12) to the Frame (1) with two
4
M6 x 48mm Screws (4) and two M6 x 16mm
Screws (5).
12
1 4
4 5
5.
Uk Manual - Page 9
... for additional exercises. Always use solvents to the exercise information accompanying your own weight set for several exercises.
ADJUSTING THE PIVOT LEG
To change the level of the Bench (12), first remove both Lock Pins. Replace any worn parts immediately.
The weight bench can be cleaned with the corresponding hole in place around the Adjustment Leg.
12...
Uk Manual - Page 10
PART LIST-Model No. Qty. Qty.
For information about ordering replacement parts, see the back cover of this manual. *These parts are subject to change without notice. WEEVBE7023.0
R0310A
Key No. Description
Key No. Exercise Guide
Note: Specifications are not illustrated.
10 Description
1
1
Frame
2
1
Pivot Leg
3
1
Adjustment Leg
4
2
M6 x 48mm Screw
5
2
M6 x 16mm ...
Uk Manual - Page 11
WEEVBE7023.0 R0310A
12
16 5
9
4 13
2
1 11
4
10
6
7
7
14 15
10
9
8
7
7
6
3
9 9
11 EXPLODED DRAWING-Model No.
Uk Manual - Page 12
...:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the front cover of this manual. ORDERING REPLACEMENT PARTS
To order replacement parts, please see the PART LIST and the...
Weider Pro 120 Bench Reviews
We have not received any reviews for Weider yet.