Genie Excelerator Support and Manuals
Get Help and Manuals for this Genie item
View All Support Options Below
Free Genie Excelerator manuals!
Problems with Genie Excelerator?
Ask a Question
Free Genie Excelerator manuals!
Problems with Genie Excelerator?
Ask a Question
Most Recent Genie Excelerator Questions
Where Does The Wire
I have a genie model 12a. When I look at the area of the hook up terminals there is a wire with a sm...
I have a genie model 12a. When I look at the area of the hook up terminals there is a wire with a sm...
(Posted by mcgoff66 1 year ago)
Status Light On Model Isd1000
what does it mean when the status light stays blinking
what does it mean when the status light stays blinking
(Posted by davono777 6 years ago)
The Learning Button Genie Excelerator Model Isd990
How do I activate it?
How do I activate it?
(Posted by rcurley 8 years ago)
Where Can I Buy A 4062 Traveler
(Posted by jiperez1961 8 years ago)
How To Replace Genie Excelerator Motor Fuse
(Posted by rnbzukk 9 years ago)
Genie Excelerator Videos
Genie Excelerator IDS990 Circuit Board Replacement
Duration: 5:19
Total Views: 3,556
Duration: 5:19
Total Views: 3,556
Popular Genie Excelerator Manual Pages
Owner's Manual - Page 1
...3531835447
TABLE OF CONTENTS
Safety Information 2 Important Installation Instructions 2 Safety Features 2 Pre-installation Checklist 3 Garage Door Opener Assembly 9 Record Data (for 8' Doors
Included Wall Control MUST be Properly Set to Operation of this Garage Door Operator. Please call us: 1-800-35-GENIE (354-3643) www.geniecompany.com
Please have Model information ready when calling...
Owner's Manual - Page 2
...174; Control Used to the door before removing operator cover. • When replacing cover, make sure wires are not pinched or near
moving . • Do Not allow children to the wall button or console. POTENTIAL HAZARD
EFFECT
PREVENTION
MOVING DOOR
WARNING: Can Cause Serious
Injury or Death
• Keep people clear of opening and closing door. IMPORTANT INSTALLATION INSTRUCTIONS
WARNING...
Owner's Manual - Page 3
... braced or reinforced before installing Opener. If your garage door for repairs
and adjustments to Opener's Door Bracket. KEEP FEET CLEAR OF DOOR
3' - 4'
Sectional Door
Check Step 2: CHECK GARAGE DOOR ALIGNMENT, OPERATION, AND BALANCE
A Raise door, check alignment and see if it is a sectional or a one -piece door. Door should stay stationary. Contact a Genie Factory Authorized Dealer
or...
Owner's Manual - Page 7
... 1L 1M 1P
Part Name
Lens Top Plate Assembly Light Socket (2) Motor Assembly Cover Motor Drive Board Controller Board No. 10-24 x 3/8" Hex Head No. 8-32 x 1" Phillips Screw No. 8-32 x 3/8" Slotted Hex Head Screw Power Cord
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
7 These items will be illustrated throughout the manual as required.
Owner's Manual - Page 8
... VIEW
NOTE
Opener will not function unless Safe-T-Beam® System is installed and Force Controls are properly set.
One-Piece Rail Assembly (Genie Pro only) for 10' or 12' door includes: • Special "Close" Limit Switch with longer Wires. • 96" Emergency Release Cord (yellow). • Rail Support Kit.
11
Rail Assembly (1 piece) (Packaged separately)
5573...
Owner's Manual - Page 20
... Controls to run, move Limit Switch toward Power Head. - If door reverses before operating the Opener. If door does not open garage door. - Do Not over -tighten.
• Re-engage Magnetic Carriage Assembly. B Setting Open Limit Switch:
• Manually open garage door to open completely, move , check Safe-T-Beam® System.
B Adjust the Close Limit Switch:
• Press Wall Console...
Owner's Manual - Page 21
.... If not, adjust Close Force Control slightly clockwise, open position using Wall Console.
• Gently adjust Close Force fully counterclockwise (minimum force).
• Run Opener using Wall Console.
• Observe that door runs to Open Limit Switch. -
D Check that door runs to Close Limit Switch. - Installation SteCpH10:
SETTING CONTACT REVERSE FUNCTION
NOTE
Limit Switch...
Owner's Manual - Page 22
... 37 Genie Remote Controls
Learn Code Button
STATUS
LEARN LEARN INDICATOR LIGHT
Figure 38 Learn Code Button and Indicator Light
Model Number
Visor Clip
Push to delete a Remote Control or Wireless Keypad, see "To Erase All Receiver Memory." ACCESSORIES
Installation SteCpH11: PROGRAMMING THE REMOTE CONTROL
A To program one time. Red Learn Indicator Light will blink 2 times per Opener.
•...
Owner's Manual - Page 23
...Learn Code Indicator LED stays on .
• Press
again.
-
Red LED blinks - B Programming One Door Operator:
Figure 1
• Find the Learn Code Button and Learn Code Indicator LED on .
• Press
.
-
Enter your PIN and try again.
• Any keypad button will control the door for this
door Opener ( or or ).
- Programming for 1 Door Opener
A Set Wireless Keypad PIN...
Owner's Manual - Page 24
...home by repair persons, meter readers, etc.
See Figure 2. • Hook the Keypad over the screw. • Mark,drill pilot hole and fasten bottom screw. • Reinstall Battery Cover.
Figure 2
1" 8
Wall
screw head gap
BATTERY CHANGES. A temporary PIN allows temporary access to "Programming for 1 Door Opener"or "Programming for the top mounting screw. • Install a screw into...
Owner's Manual - Page 25
... in Set Limit Switches and Force Controls on back of the FCC Rules. If the Opener still fails, contact a Genie Factory Authorized Dealer for service or call Customer Service at that may damage the Opener. B Install Lens into slots on page 20. Contact a Genie Factory Authorized Dealer for service or call Customer Service at 1-800-35-GENIE.
• Balance Door. - If the door moves...
Owner's Manual - Page 26
WARNING
Use the Wall Console included with the Door Controls. Any other wall console can cause the Opener to operate unexpectedly and the light to cables, spring assemblies, and other hardware.
8 SAVE THESE INSTRUCTIONS.
After adjusting either the Force or the Limit of severe injury or death. IMPORTANT SAFETY INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH
1 READ...
Owner's Manual - Page 27
...Motor Drive Board. -
See Door
Safety Guide See page 16. For Help, call Customer Service at 1-800-35-GENIE.
• If Safe-T-Beam® problems exists, the door can be installed and operational to enable door to the Opener.
Wait 10 minutes for further assistance. NOTE: Force Settings are restored at Power Head and Wall Console. Check door condition. The Green LED light will run...
Owner's Manual - Page 28
... Customer Service at Power Head Terminals (see Set Limit Switches and Force Controls on page 20). Adjust as needed . Replace as needed .
• Disconnect Wires connecting Wall Console to Power Head (see Set Limit Switches and Force Controls on page 20). Door Opener starts for remaining remote controls. (See Erase All Receiver Memory on page 22).
• Ensure that Carriage...
Owner's Manual - Page 29
... of Wall Console Vacation Lock Switch. It must be in good repair, properly lubricated, and properly
balanced. (See Maintenance page 25).
• WARNING: If you suspect a problem with garage door hardware or springs, contact a Genie Factory Authorized Dealer for Opener to retune Remote Controls or Receiver.
• Program code for each Remote Control into Receiver memory (See Programming the...
Genie Excelerator Reviews
We have not received any reviews for Genie yet.