English Manual
Page 3
... the barbell if you are adequately informed of weight (not included) on the weight rests to balance the bench. 14. Make sure all users of the weight bench are performing bench press exercises, your barbell when you to support a maximum of the barbell when adding or removing weights to the... locked position. 16. Use the weight bench only as described in an inclined position, make sure that the support ...
... the barbell if you are adequately informed of weight (not included) on the weight rests to balance the bench. 14. Make sure all users of the weight bench are performing bench press exercises, your barbell when you to support a maximum of the barbell when adding or removing weights to the... locked position. 16. Use the weight bench only as described in an inclined position, make sure that the support ...
English Manual
Page 7
Lubricate the M10 x 60mm Bolt (27). Press two 19mm Round Inner Caps (16) into the indicated end of the two Pad Tubes. 4 14... 29 35 6 16 17 16 16 17 16 18 7 Slide the Weight Tube through the holes in the Leg Lever (6). Press a 25.4mm Angle Cap (20) onto the other end of the name decal and make sure the Uprights are oriented as shown...Name 3 Decal 22 12 2 23 4. Do not overtighten the Nylon Locknut; Slide a Foam Pad (18) onto each Pad Tube (17). Press a 25.4mm Round Inner Cap (19) into each side of the Weight Tube (37). 3. Do not tighten the Nylon Locknuts yet. Attach...
Lubricate the M10 x 60mm Bolt (27). Press two 19mm Round Inner Caps (16) into the indicated end of the two Pad Tubes. 4 14... 29 35 6 16 17 16 16 17 16 18 7 Slide the Weight Tube through the holes in the Leg Lever (6). Press a 25.4mm Angle Cap (20) onto the other end of the name decal and make sure the Uprights are oriented as shown...Name 3 Decal 22 12 2 23 4. Do not overtighten the Nylon Locknut; Slide a Foam Pad (18) onto each Pad Tube (17). Press a 25.4mm Round Inner Cap (19) into each side of the Weight Tube (37). 3. Do not tighten the Nylon Locknuts yet. Attach...
English Manual
Page 8
6. Press a 25.4mm Round Inner Cap (19) into each Backrest Tube (8). 6 9 Attach the Backrest Tubes (8) to the Backrest (9) with three M6 x 38mm Screws (24) and three ... the M8 Nylon Locknuts (23) used in the Backrest. Attach the Seat (10) to the Backrest (9) with four M6 x 16mm Screws (21). 8 10 4 21 21 8 Press four 25.4mm Square Inner Caps (15) into place around the Upright.
6. Press a 25.4mm Round Inner Cap (19) into each Backrest Tube (8). 6 9 Attach the Backrest Tubes (8) to the Backrest (9) with three M6 x 38mm Screws (24) and three ... the M8 Nylon Locknuts (23) used in the Backrest. Attach the Seat (10) to the Backrest (9) with four M6 x 16mm Screws (21). 8 10 4 21 21 8 Press four 25.4mm Square Inner Caps (15) into place around the Upright.
English Manual
Page 10
... THE BACKREST The Backrest (9) can be adjusted. To use Olympic weights, press the two Adapter Bushings (32) into place around the Upright. Slide the... (1). Inspect and tighten all parts each exercise. Replace any worn parts immediately. To use the weight bench. To use the Backrest (9) in an incline position, lift the Backrest and insert the Support Rod ...in a decline position, a level position, or three incline positions. The steps below explain how the weight bench can be cleaned with your weight set (not included) for additional exercises. WARNING: Do not place more than...
... THE BACKREST The Backrest (9) can be adjusted. To use Olympic weights, press the two Adapter Bushings (32) into place around the Upright. Slide the... (1). Inspect and tighten all parts each exercise. Replace any worn parts immediately. To use the weight bench. To use the Backrest (9) in an incline position, lift the Backrest and insert the Support Rod ...in a decline position, a level position, or three incline positions. The steps below explain how the weight bench can be cleaned with your weight set (not included) for additional exercises. WARNING: Do not place more than...