Owner's Manual
Page 2
...maximum safety, set the force required for opening and closing door. The light turns on , or next to which door spring parts are fastened, such...information presented, call your service representative. 2 Do Not install operator on the floor at 1-800-35-GENIE.. An improperly balanced door could cause severe injury. Force Guard® Control Used to set the ... near moving objects, springs under high tension and electric opening equipment may cause injuries, your nearest Genie Factory Authorized Dealer listed at www.geniecompany.com, or customer Service at the center of the doorway...
...maximum safety, set the force required for opening and closing door. The light turns on , or next to which door spring parts are fastened, such...information presented, call your service representative. 2 Do Not install operator on the floor at 1-800-35-GENIE.. An improperly balanced door could cause severe injury. Force Guard® Control Used to set the ... near moving objects, springs under high tension and electric opening equipment may cause injuries, your nearest Genie Factory Authorized Dealer listed at www.geniecompany.com, or customer Service at the center of the doorway...
Owner's Manual
Page 10
...Figure 13 Attach Rail Strap White Wire 21 Assembly Step C6H: INSTALL AND CONNECT LIMIT SWITCHES OPEN GREEN PARTS BAG A Turn Opener right side up and support Power Head to End Rail Section with 2 (1/4"-20) Hex Head Bolts and 2 (1/4"-...C4H: ATTACH RAIL STRAP TO END RAIL SECTION Rail Strap 15 16 A Attach Rail Strap to avoid damaging the Light Bulb Sockets. Assembly Step C5H: ALIGN RAIL SECTIONS AND TIGHTEN ALL BOLTS A Align all fasteners now. Assembly Step... Slide Magnetic Carriage Assembly into slot on Assembled Rail 10 For Help, call 1-800-35-GENIE or visit www.geniecompany.com
...Figure 13 Attach Rail Strap White Wire 21 Assembly Step C6H: INSTALL AND CONNECT LIMIT SWITCHES OPEN GREEN PARTS BAG A Turn Opener right side up and support Power Head to End Rail Section with 2 (1/4"-20) Hex Head Bolts and 2 (1/4"-...C4H: ATTACH RAIL STRAP TO END RAIL SECTION Rail Strap 15 16 A Attach Rail Strap to avoid damaging the Light Bulb Sockets. Assembly Step C5H: ALIGN RAIL SECTIONS AND TIGHTEN ALL BOLTS A Align all fasteners now. Assembly Step... Slide Magnetic Carriage Assembly into slot on Assembled Rail 10 For Help, call 1-800-35-GENIE or visit www.geniecompany.com
Owner's Manual
Page 23
...while door is blinking rapidly,the PIN was entered incorrectly. once per second and turns off . C Operating One Door Operator: • To move ,check the red LED on next page) For Help, call 1-800-35-GENIE or visit www.geniecompany.com 23 If the LED is moving door and its parts... blink. • Enter your door opener has a black antenna Indicator LED wire,the Learn Code Button and Indicator LED are located near the antenna. (The light lens may need to be door #1,#2 and #3. • Press the Learn Code Button (see Figure 1). - To keep the door from the Wireless Keypad. ...
...while door is blinking rapidly,the PIN was entered incorrectly. once per second and turns off . C Operating One Door Operator: • To move ,check the red LED on next page) For Help, call 1-800-35-GENIE or visit www.geniecompany.com 23 If the LED is moving door and its parts... blink. • Enter your door opener has a black antenna Indicator LED wire,the Learn Code Button and Indicator LED are located near the antenna. (The light lens may need to be door #1,#2 and #3. • Press the Learn Code Button (see Figure 1). - To keep the door from the Wireless Keypad. ...
Owner's Manual
Page 27
... must be closed electrically by holding the Wall Console Button down until door is fully closed. • The Remote Controls and Wireless Keypad will turn ON, then OFF when power is in a "ONE-BLINK" signal. See Door Safety Guide See page 16. Check door condition. Contact Customer... Cover. See page 18 NOTE • The status LED Indicator Light is equipped with an automatic garage door balance detection system. If LED stays ON, have a Genie Factory Authorized Dealer check the Controller Board, or call 1-800-35-GENIE or visit www.geniecompany.com 27 See Door Safety Guide 1.
... must be closed electrically by holding the Wall Console Button down until door is fully closed. • The Remote Controls and Wireless Keypad will turn ON, then OFF when power is in a "ONE-BLINK" signal. See Door Safety Guide See page 16. Check door condition. Contact Customer... Cover. See page 18 NOTE • The status LED Indicator Light is equipped with an automatic garage door balance detection system. If LED stays ON, have a Genie Factory Authorized Dealer check the Controller Board, or call 1-800-35-GENIE or visit www.geniecompany.com 27 See Door Safety Guide 1.
Owner's Manual
Page 28
...-GENIE. • Check Open Limit Switch for a short circuit and for no apparent reason Door starts down , then stops and goes back up , but door does not move • Check (ensure) that all Remote Control codes from Remote Control 1. General Troubleshooting (Always Check the Status LED Light... controls. (See Erase All Receiver Memory on page 22). • Ensure that Carriage activates Close Limit Switch. Door starts up Door will not turn off • Check Safe-T-Beam® System as needed . • Disconnect Wires connecting Wall Console to a wiring box: • Check fuse...
...-GENIE. • Check Open Limit Switch for a short circuit and for no apparent reason Door starts down , then stops and goes back up , but door does not move • Check (ensure) that all Remote Control codes from Remote Control 1. General Troubleshooting (Always Check the Status LED Light... controls. (See Erase All Receiver Memory on page 22). • Ensure that Carriage activates Close Limit Switch. Door starts up Door will not turn off • Check Safe-T-Beam® System as needed . • Disconnect Wires connecting Wall Console to a wiring box: • Check fuse...