Genie IntelliG 1000 Support Question
Genie IntelliG 1000 Support Question
Find answers below for this question about Genie IntelliG 1000.Need a Genie IntelliG 1000 manual? We have 1 online manual for this item!
Question posted by yinchiu85 on January 5th, 2022
Red Light Flashing, Door Not Opening
My genie IntelliG 1000 originally has purple solid light, and it turns to flashing red light after i unplug and re -plug it. However, after the replug, I still have the opening problem and door can not be opened. Please kindly share the trouble shoot if anyone had the same issue and experience. THanks,
Current Answers
Answer #1: Posted by SonuKumar on January 6th, 2022 8:15 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,604,580
Member since:
May 9th, 2021 Points: 16,604,580
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Genie IntelliG 1000 Manual Pages
Owner's Manual - Page 1
... GPower are trademarks of GMI Holdings, Inc., dba The Genie Company Homelink is a registered trademark of Johnson Controls Technology Company. GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
SCREW/BELT/CHAIN DRIVES
OPERATION & MAINTENANCE MANUAL
Includes...
Owner's Manual - Page 3
...your local Genie® Factory Authorized Dealer.
• DO NOT install operator on an improperly balanced door. This is about the size
at the center of opening while door is ... INFORMATION
CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are NOT pinched or near moving parts. If you reading the information in Death or Serious
Injury
Turn OFF power before installing operator.
&#...
Owner's Manual - Page 4
... garage.
Used during the closing of contact with : Open/Close, Sure-Lock™, and independent light control buttons. Turns ON when door is detected for safer evening exits and entries. Integrated Motion Detection (Not available on the STBs provide a self-diagnostic code if an operational problem exists. Wall Console Operates door opener from door opener. Lights automatically turn...
Owner's Manual - Page 5
... up your Genie garage door opener is needed to how fast or slow your opener opens and closes your opener so it functions properly for programming ONLY.
This function does NOT require programming. ROUND LED Indicator
Open Travel Close Travel Button
PROGRAM
SET
- +
LONG LED Indicator
Located on the powerhead of three different colors: blue, red or purple. These buttons...
Owner's Manual - Page 6
...from wall console before LIMITS are set.
See page 17. If you see two solid red or flashing LEDs on the rail.
4 Press and hold the down arrow button (-) for...Garage Door (Down Limits)
1 Lift the door open by hand until the shuttle/bullet
engages the carriage on the Powerhead, you have 30 seconds to complete each step. NOTE: Before setting limits confirm wall console red indicator light...
Owner's Manual - Page 7
... ) limit is programmed.
8 Press and hold the up arrow button (+) for
2 seconds until door
is fully open ) limit is recommended but not necessary.
6 Press and hold the up arrow button (+) and the round LED
will begin flashing. PROGRAM
SET
-
HOLD
Opening Garage Door (Up Limits)
NOTE: Beginning with powerhead. PROGRAM
PROGRAM
SET
-
PROGRAM
PROGRAM
- +
SET
The...
Owner's Manual - Page 8
... as motion is ON, indicator light flashes.
Open/Close Button Use this button to open or close garage door.
Independent Light Control Button Use this button to turn powerhead lights ON.
Indicator Light -Red indicator light is always ON. -When Sure-Lock™ is detected. Independent Light Control Button Controls door opener lights from inside garage. In your carton you will...
Owner's Manual - Page 9
... to these functions for the rst time. Contact Reverse Adjustment
If the door stops before contacting the board or if it does not reverse direction to fully open and close your garage door. Repeat step 10 to set and rarely require adjustments.
Red LED lights on the Wall Console.
NOTE: Force or Speed controls DO NOT...
Owner's Manual - Page 11
...'s flash blue and then turn off). Each Remote can be programmed for additional Remotes. Repeat as described in "Learn Mode" as necessary for three door openers. PROGRAM
SET
-
Follow the Car2U or HomeLink instruction to set the button in the "Accessory" position.
The Remote button is now programmed. BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR...
Owner's Manual - Page 12
...Opener
4. Press Up/Down key again. Door opener will turn o . 5. When the door has stopped moving, pressing on any key will stop fully open or closed. Press and hold Program key and then the Up/Down key for 5 seconds or until backlight goes off (30 seconds)
NOTE: Rapid blinking of the red... ashing purple
Opener
2. The door will stay on the Powerhead indicates an error.
Opener LEDs will...
Owner's Manual - Page 13
...operate normally using the Wall Console. Your opener will not activate the door opener. All remaining (or recovered) Remotes and...the memory is pressed the round LED will flash blue but will not activate the door opener. NOTE: The garage door opener will clear ALL programmed Remotes and wireless ... the Powerhead
and hold until both LEDs flash blue and then go OFF.
T
- +
SET
HOLD 2 ...
Owner's Manual - Page 14
... the button for operation with Intellicode® 2 openers. The light lens may need to Intellicode® 1. NOTE: Choose the Genie® Remote using Intellicode® 1 button for this activity. If your older Genie® door opener. If you have the button directly above the logo on the Remote turn the RED LED on the Remote back to GREEN...
Owner's Manual - Page 16
... items below:
• STB red LED flashes. -
This indicates the system is improperly balance or springs are capable of increasing the rate of door closure and increasing the risk of travel, retest door opener. Failure to repair or adjust door springs or any hardware, and DO NOT OPERATE garage door automatically or manually if door is working properly, perform...
Owner's Manual - Page 17
...Replace battery. 3. Disconnect power to carriage assembly. Close powerhead light cover. 2. Reconnect power to carriage, pull the release handle down on relaese hanfle. Note: The opener will re-attach itself to door opener. • Open powerhead light cover. • Remove light bulb(s). • Replace light bulb(s).
- DO NOT use light bulbs with a CR 2032 coin cell battery. 1. To...
Owner's Manual - Page 18
...
PURPLE
PURPLE
Off
PURPLE
PURPLE
Off
RED
RED
Off
RED
RED
18
G999-393 Manual-ScrewBeltChain-EN indd 18
(continued next page)
7/13/12 10 17 AM Doors that start down buttons 2 seconds or until round LED turns RED.
2 Press either until you reach the desired setting.
5 Press and release. Doors that start up and down , STOP, and reverse before they completely open...
Owner's Manual - Page 19
... CHART IN NEXT COLUMN.
Sun
Red
Green
LED
LED
One Door Garage
19
G999-393 Manual-ScrewBeltChain-EN indd 19
7/13/12 10 17 AM Note: PowerLift® 900, GPower™ 900 openers DO NOT have the option to confirm setting. SET
Then release. SEE CHART IN NEXT COLUMN. Flashes BLUE 3 Times
OFF
Then the...
Owner's Manual - Page 21
...; Check for binding. • If an operational problem exists, and opener will only open .
• Check if limits are properly set . See pages 6-7. • Check if Safe-T-Beam® Red LED is flashing. • Check Safe-T-Beam® system for beam obstruction or misalignment of lenses. • Check garage door for interference from www.geniecompany.com
•...
Owner's Manual - Page 22
...LEDS
Powerhead LED
Round LED
Long LED
OFF
OFF
ON/RED/ STEADY
ON/RED/ FLASHING
ON/BLUE/ FLASHING
ON/PURPLE/ FLASHING
ON/RED/ STEADY ON/RED/ FLASHING
OFF
OFF
ON/RED/ FLASHING
OFF
OFF
OFF
ON/RED/ FLASHING
ON/RED/ STEADY
Possible Problem
Normal operation.
Unplug unit, wait 5 seconds, plug in. Contact a trained door system technician. Intellicode® 1 remote NOT programmed. Wait until...
Owner's Manual - Page 23
...SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
LIMITED WARRANTY
GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ("Product...
Owner's Manual - Page 24
...
(Works with Revolution Series 1500, 1200 and 1000 Models)
• Sleek and compact design
• Beeps and flashes green when garage door closes. Garage Door Opener Accessories
Looking for extra safety
• Ball and string system attaches to mount inside garage
• Used in One
Keyless Entry Pad • Wireless;
Genie® Has the Answer! visit www.GenieCompany.com...
Similar Questions
No Power
my opener lost all power today, I confirmed theoutlet has power.
my opener lost all power today, I confirmed theoutlet has power.
(Posted by Danatsma 3 years ago)
Genie Powerlift 900 Won't Find Remote During Programming
Remotes stopped working. Replaced battery and purchased a new remote. Attempting to program each rem...
Remotes stopped working. Replaced battery and purchased a new remote. Attempting to program each rem...
(Posted by imgoggleman 9 years ago)
Garage Door Opener Not Working
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
(Posted by scanty5 9 years ago)
Red Light(not Blinking) On The Opener Is On All The Time, What Is The Problem?
Red light(not blinking) on the opener is on all the time, what is the problem? We have a problem wit...
Red light(not blinking) on the opener is on all the time, what is the problem? We have a problem wit...
(Posted by rowannawong 10 years ago)
How Do I Get The Home Link In My Jeep Programmed To The Opener?
(Posted by sandraguyer 10 years ago)