Genie IntelliG 1000 Support Question
Genie IntelliG 1000 Support Question
Find answers below for this question about Genie IntelliG 1000.Need a Genie IntelliG 1000 manual? We have 1 online manual for this item!
Question posted by imgoggleman on February 15th, 2015
Genie Powerlift 900 Won't Find Remote During Programming
Remotes stopped working. Replaced battery and purchased a new remote. Attempting to program each remote but the unit never finds the remote following the procedure in the manual. Purple light blinks but never picks up either remote when pushing the remote buttons. Eventually the process times out and the light on the unit turns red. Is this a problem with the eye on the unit and is there a way to repair?
Current Answers
Related Genie IntelliG 1000 Manual Pages
Owner's Manual - Page 1
...., dba The Genie Company Homelink is a registered trademark of injury to persons or damage to property - GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
SCREW/BELT/CHAIN DRIVES
OPERATION & MAINTENANCE MANUAL
Includes INTELLICO®DE 2 Remote Control.
Owner's Manual - Page 2
... Remotes/New Intellicode 2 Openers 10
O5ptional 6Program7ming
Keypad 12 Clearing Memory for Remotes 13 Intellicode 1 Remotes 14
O6ne Piece7Doors
Attaching Door Bracket to Door 15 Attaching Door Arm... comply with all United States and Canadian legal
requirements as of the date of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7...
Owner's Manual - Page 3
...Genie® Factory Authorized Dealer.
• DO NOT install operator on an improperly balanced door. When replacing cover, make sure wires are fastened, such as, wood blocks, steel brackets, cables or other hardware must be done by a trained service person using proper tools and instructions. Opener... SEVERE INJURY OR DEATH
READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS...
Owner's Manual - Page 4
... required to download a printable file.
Lights will stop and reverse a closing door if a problem is interrupted by continuously changing the access code each time the remote is installed improperly, press and hold the wall console "open /close . 3.When the garage door is closing door within two seconds of opener. An access code copied from a working system and tried again, will...
Owner's Manual - Page 5
... bottom of three different colors: blue, red or purple. Multi-function;
This function does NOT require programming. The LED lights indicate status or a function change by illuminating ON, OFF, or ON FLASHING in the garage door opening and closing your garage door.
Remote Programming synchronizes your remote control devices (remotes, wall console, and keypad) with the powerhead.
Force...
Owner's Manual - Page 6
...PROGRAM
SET
+
NOTE: If shuttle/bullet has NOT been engaged to execute each step.
(continued next page)
G999-393 Manual-ScrewBeltChain-EN indd 6
7/13/12 10 17 AM
See page 17. Closing Garage Door (Down Limits)
1 Lift the door open... indicator light (or backlight) is ON.
Severe damage to the opener can restart as many times as necessary to carriage BEFORE setting limits. PROGRAM
SET
...
Owner's Manual - Page 7
... (both
LEDs flash blue and go off). BOTH DOOR LIMITS ARE NOW PROGRAMMED.
7
7/13/12 10 17 AM PROGRAM
PROGRAM
- +
ET
G999-393 Manual-ScrewBeltChain-EN indd 7
The UP (open , then release. PROGRAM
SET
-
Watch carriage as it approaches the power head to avoid contact with garage door closed ) limit is programmed.
8 Press and hold the up arrow button (+) for...
Owner's Manual - Page 8
... open or close door.
W B/W
- UNLOCK allows controls to
work normally. TIP
FROM STBs OM STB
FROM WALL CONSOLE
FROM STBs
FROM WALL CONSOLE
STB BWC IWC
NOT NOT USED USED
STB BWC IWC
G999-393 Manual-ScrewBeltChain-EN indd 8
7/13/12 10 17 AM Open/Close Button Use this unit.
Powerhead lighting will CLOSE the door only. 3 Required Programming...
Owner's Manual - Page 9
....
Repeat this manual (pages 18-19).
10 Open and close your garage door using the Wall
Console Open/Close button.
13 Close the garage door using the Open/Close button
on the powerhead will clear the lights. When the door contacts the board, it is closing tight to open and close your garage door.
NOTE: Force or Speed controls DO NOT require programming. Contact...
Owner's Manual - Page 10
...of time and must be programmed separately, following instructions are for the remote control transmitters ("Remotes") provided with the Intellicode 2 Access Security System. NOTE: Each button on Intellicode 1 and 2 Remotes and how to switch from remote. 3 Required Programming
REMOTES / New Intellicode 2 Openers
NOTE: The following these steps.
14 Press and hold Remote too close to the...
Owner's Manual - Page 11
Each Remote can be programmed for other garage door openers, repeat the steps above using one of the other two Remote buttons.
to connect to set the button in the "Accessory" position. G999-393 Manual-ScrewBeltChain-EN indd 11
11
7/13/12 10 17 AM Follow the Car2U or HomeLink instruction to your Intellicode remote when it's searching
SET
-
PROGRAM
SET...
Owner's Manual - Page 13
... and
hold 2 seconds, round LED comes ON.
PROGRAM
PROGRAM
SET
SET
HOLD HOLD
If the memory has been cleared, the Remote will not activate the door opener.
NOTE: Clearing Remotes from a missing Remote.
G999-393 Manual-ScrewBeltChain-EN indd 13
(continued next page) 13
7/13/12 10 17 AM NOTE: The garage door opener will clear ALL programmed Remotes and wireless Keypads.
Owner's Manual - Page 14
...® 1 model of Genie® garage door openers .The default Intellicode® 2 setting must be changed to Intellicode® 1. (Follow these same steps to change Intellicode® 1 back to Intellicode® 2.)
NOTE: The button directly above the logo preset to Intellicode® 1.
1 Select a Remote button NOT already programmed to the Intellicode® 1.
3 Find the Learn Code Button and...
Owner's Manual - Page 16
... and lower the door manually-it should stop and
reverse to prevent contacting it . NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. 4. An improperly balanced door increases the risk of any hardware, and DO NOT OPERATE garage door automatically or manually if door is working properly, perform the check as follows:
• With the door closed, pull manual emergency release handle...
Owner's Manual - Page 17
... from a ladder or step stool. • When replacing light cover, make sure wires are programmed. Open remote case using a remote or wall console. - Replace battery. 3. CORRECTIVE MAINTENANCE
Changing Light Bulbs
WARNING
• Use extreme caution when working from carriage, pull down and toward the door. Close powerhead light cover. 2. Disengaging and Engaging Carriage/Bullet
Screw...
Owner's Manual - Page 19
... side
Multiple Garage Doors • NEVER position Safe-T-Beam modules where signals will display.
However, travel will display.
6 Maintenance and Adjustments
Adjustment Guides (continued)
Speed Settings (DC motors only) Speed settings are 3-speed settings available for sectional doors.
LOCKS IN CLOSING SETTING. Note: PowerLift® 900, GPower™ 900 openers DO NOT...
Owner's Manual - Page 21
... only run from powerhead memory and program new remotes. See page 13.
21
G999-393 Manual-ScrewBeltChain-EN indd 21
7/13/12 10 17 AM DO NOT RETURN to close , the opener can cut wires. Check connections at powerhead terminals and at garage door.
• Replace battery.
See pages 10-11.
If lamp works, power source is engaged into outlet...
Owner's Manual - Page 22
... tight. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is lowest speed setting. • If carriage travel . Re-program limits, see page 19.
Intellicode® 1 remote NOT programmed.
Remove obstruction, recheck unit. DO NOT unplug unit.
No response from unit.
Thermal cutout
Program remote using instructions on a one...
Owner's Manual - Page 23
...8482; 900, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
LIMITED WARRANTY
GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers...
Owner's Manual - Page 24
... addition to door - Genie-Net™ technology "tells" you! G999-393 Manual-ScrewBeltChain-EN indd 24
™ 7/13/12 10 17 AM Closed Confirm™ Wireless Remote
(Works with flip-up cover • Controls up to 3 openers • Large, easy to find buttons for Leading-Edge Technology or the Perfect Update/Replacement? Also available at your garage door close properly...
Similar Questions
Red Light Flashing, Door Not Opening
My genie IntelliG 1000 originally has purple solid light, and it turns to flashing red light after i...
My genie IntelliG 1000 originally has purple solid light, and it turns to flashing red light after i...
(Posted by yinchiu85 2 years ago)
What Remote Do I Use For Powerlift Garage Door Opener Model Wr77 Serial No.08258
(Posted by tmski87 3 years ago)
Genie Garage Door Opener Silentmax 1000 Won't Close Completely
(Posted by khetach 9 years ago)
How Do I Get The Home Link In My Jeep Programmed To The Opener?
(Posted by sandraguyer 10 years ago)
How Do I Program A Girt-3 With The Intellig 1000?
(Posted by kweber35 11 years ago)