Weider 8515 Support and Manuals
Get Help and Manuals for this Weider item
Most Recent Weider 8515 Questions
What Length Of Cable I Needed For Welder 8515 Home Gym
I have a welder 8515 home gym set I can't find the serial number for the cables needed I noticed it'...
I have a welder 8515 home gym set I can't find the serial number for the cables needed I noticed it'...
(Posted by jaguarparkside 2 years ago)
Need Help With Cable Diagram
(Posted by Aml309 10 years ago)
Popular Weider 8515 Manual Pages
User Manual - Page 1
... eclUiprnent.
The trained technicians on our customer hot line will guarantee you complete satisfaction through direct assistance from our factory. TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. Read all precautions and instructions in the space above for futUre' reference.
8515
PATENT PENDING
) 00 00
0
USER'S MANUAL Model No. Write...
User Manual - Page 2
... ASSEMBLY HOW TO USE THE HOME GYM SYSTEM TROUBLESHOOTING AND MAINTENANCE CABLE DIAGRAM ORDERING REPLACEMENT PARTS
2 3 4 5 15 18 19 Back Cover
Note: A PART IDENTIFICATION CHART and a PART ...manual. This warranty gives you . ICON's obligation under this product to replacing or repairing, at ICON's option, the product at one of purchase. All products for products used as store display models...
User Manual - Page 3
... stand on a level surface.
Always disconnect the lat bar from the home avm system when performing an exercise that could cause the home gym system to cool before using the home gym system. The weights will fall with pre-existing health problems. Read all instructions in this manual and in the accompanying literature before touching them.
12. The resistance cylinders...
User Manual - Page 4
... reading further, please review the drawing using the WEIDER® 8515 Home Gym System. Service Department toll-free at 1-800-225-0653, Monday through Friday, 6 a.m. High Pulley Station Lat Bar
Butterfly Arms Backrest Press Arm Seat
Leg Lever
Foot Plate
O
0 0
O 0
4
Resistance Cylinders
Stepper Pedals
0
Weight Pin
Weight Stack Low Pulley Station Width: 40 in . Length: 53 in . To...
User Manual - Page 5
..., or a set of the Base (4) onto the 5/16" x 2 3/4" Carriage Bolts (14) in the box above. Slide the indicated end of ratchet wrenches.
Before beginning assembly, be more convenient if you assemble them, unless instructed to see if it has been pre-attached.
• As you assemble the WEIDER 8515, be needed. The hardware for shipping. If a part is...
User Manual - Page 7
..." logo is oriented as shown. Tap the Retainer and Round Cover Cap onto the cylinder axle. C!)
Cf) 7.
Set two Weight Bumpers (19) onto the brack-
8
et on the Rear Upright (56). Lubricate the cylinder axles on top.
... (79) onto the left cylinder axle in the same manner.
6. Stack six Weights (25) onto the Weight Bumpers (19). Be sure that the pin grooves are all on the same side...
User Manual - Page 8
...
Lubricate the inside of the indicated tube in the Base. Be sure that the pulleys are sitting in the pin grooves in the Weight Guides are at the top, as shown.
61 3 55
60 20
62
11. ... Pulley Bracket (20) is in the Top Weight (76). Set the Top Weight onto the stack of Weights (25). Attach the upper ends of the right Weight Guide (62) as shown. Be sure that the pins on the Weight...
User Manual - Page 10
... shown).
Be sure that the Cable (23) is turned to hold the Cable in place.
< 16.
Attach a 3 1/2" Pulley (15) and a Cable Trap (66) to the CABLE DIAGRAM on the Right Arm (48). As you assemble the cables and pulleys in steps 14 through the 3 1/2" Pulley (15) and Long "U"-Bracket (57). Route the Long Cable (23) around the 3 1/2" Pulley (15) attached to the Top...
User Manual - Page 11
...Pulley is routed around the Pulley as shown. Route the Short Cable (58) around the 3 1/2" Pulley (15) attached to the lower hole in place and that the Cable is pre-assembled. Route the Short Cable (58) around the 3 1/2"
2
Pulley... Locknut. It has been shown disassembled for easy part identification.) Be sure that the Cable and Pulley move smoothly.
19. Tighten the 3/8" Nylon Locknut...
User Manual - Page 14
Use of this manual for proper cable routing. 28. Before using the home gym system, pull each cable a few times to the home gym system in the locations shown in the illustration below.
28
HIGH PULLEY
BUTTERFLY
8515
STAIR CLIMBER
(t)
BENCH PRESS
LEG DEVELOPER
0
Op co
O
0
O
LOW PULLEY
29. See TROUBLE-SHOOTING AND MAINTENANCE on page 15 of the remaining parts will be explained in...
User Manual - Page 15
.... Refer to the exercise poster accompanying this manual to 81.5 pounds, in the correct starting position for the exercise to the Short Cable (58) with two Cable Clips. The weight setting of the weight stack can be adjusted. Adjust the length of 12.5 pounds. HOW TO USE THE HOME GYM SYSTEM
The instructions below describe how each part of resistance at each...
User Manual - Page 16
...some exercises, the Seat (13) must be . Attach one end of the Chain to the Eyebolt (35) with a Cable Clip.... Make sure that the chain is not attached to the front upright (see ATTACHING AND REMOVING THE SEAT above). ATTACHING AND REMOVING THE SEAT
Set...).
ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION
To use . Attach the Seat Frame to the Short Cable (58) with the 5/16" x 2...
User Manual - Page 17
... butterfly arm resistance listed is the resistance for each station. WEIGHT PLATES
PRESS ARM (lbs.)
BUTTERFLY ARM (lbs.)
LEG LEVER HIGH PULLEY LOW PULLEY
(lbs.)
(lbs.)
(lbs.)
Top
20
1
45
2
70
3
99
4
128
5
153
6
184...refers to the 12.5 lb. The other numbers refer to the 6.5 lb. WEIGHT RESISTANCE CHART
This chart shows the approximate weight resistance at each butterfly arm.
User Manual - Page 18
...other hole in the cables before tightening the cables. Tighten the 1/4" Nylon Locknut (2)
2
at the end of the Short Cable (58). To do this manual.
18
The home gym system can be replaced, see ORDERING REPLACEMENT PARTS on the home gym system, can be tightened. Tighten the 1/4" Nylon Locknut (2) at the end of the Long Cable (23). TROUBLE-SHOOTING AND MAINTENANCE
Inspect...
User Manual - Page 19
... the cables will not function properly and damage may occur. Use the diagram to be positioned so that the two cables have not been correctly routed, the home gym system will not come off the pulleys. CABLE DIAGRAM
The cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). If the cables have been assembled correctly. Examine all cable traps...
Weider 8515 Reviews
We have not received any reviews for Weider yet.