User Manual
Page 1
... On-screen Display Menus 20 How to operate ...20 Menu Tree...21 Image ...22 Display ...27 Setup...30 Options...32 Appendices 34 Troubleshooting 34 Image Problems 34 Intermission Problems 37 LED Problems ...37 Remote Control Problems 38 Replacing the Lamp 39 Compatibility Modes 40 Ceiling Mount Installation 41 Optoma Global Office 42 1
... On-screen Display Menus 20 How to operate ...20 Menu Tree...21 Image ...22 Display ...27 Setup...30 Options...32 Appendices 34 Troubleshooting 34 Image Problems 34 Intermission Problems 37 LED Problems ...37 Remote Control Problems 38 Replacing the Lamp 39 Compatibility Modes 40 Ceiling Mount Installation 41 Optoma Global Office 42 1
User Manual
Page 14
... on again after 5 seconds. 2. Under normal conditions, the projector can be switched on , you should contact your local dealer or our service center. If the problem persists, you must wait until the projector has completed the cooling cycle and has entered standby mode. Press the "Standby/On" button to restart the...
... on again after 5 seconds. 2. Under normal conditions, the projector can be switched on , you should contact your local dealer or our service center. If the problem persists, you must wait until the projector has completed the cooling cycle and has entered standby mode. Press the "Standby/On" button to restart the...
User Manual
Page 34
...or control panel. If you have removed the lens cap and the projector is recommand for details) Image Problems No image appears on . Appendices Troubleshooting If you experience a problem with your projector, please refer to SXGA+ (1400 x 1050). (*) 4. Click on the "Advanced Properties" ... correctly and securely connected as described in the "Installation" section. Ensure the pins of connectors are using . If a problem persists, please contact your local reseller or service center. (See page 42 for computer signal. Please refer to the following information. Refer...
...or control panel. If you have removed the lens cap and the projector is recommand for details) Image Problems No image appears on . Appendices Troubleshooting If you experience a problem with your projector, please refer to SXGA+ (1400 x 1050). (*) 4. Click on the "Advanced Properties" ... correctly and securely connected as described in the "Installation" section. Ensure the pins of connectors are using . If a problem persists, please contact your local reseller or service center. (See page 42 for computer signal. Please refer to the following information. Refer...
User Manual
Page 36
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD. Intermission Problems The projector stops responding to 12.0 meters) from the OSD and adjust the projection direction. If you play anamorphic DVD or 16:9 DVD, the projector ...
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD. Intermission Problems The projector stops responding to 12.0 meters) from the OSD and adjust the projection direction. If you play anamorphic DVD or 16:9 DVD, the projector ...
User Manual
Page 37
... on page 39. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on until the lamp module has been replaced. LED Problems LED lighting message Message Standby State (Input power cord) Standby/On LED (Green) Flashing Power on (warming) Lamp lighting Power off the projector, then unplug...
... on page 39. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on until the lamp module has been replaced. LED Problems LED lighting message Message Standby State (Input power cord) Standby/On LED (Green) Flashing Power on (warming) Lamp lighting Power off the projector, then unplug...
User Manual
Page 38
Move to within 6 m (20 ft) of the projector. Make sure batteries are inserted correctly. Make sure batteries are not any obstructions between the remote con- Appendices Thermal Warning: Replacing the lamp: Remote Control Problems If the remote control does not work Check the operating angle for the remote control is approximately ±22.5°. Make sure there are exhausted. trol and the projector. If so, replace weak batteries in the remote control. 38
Move to within 6 m (20 ft) of the projector. Make sure batteries are inserted correctly. Make sure batteries are not any obstructions between the remote con- Appendices Thermal Warning: Replacing the lamp: Remote Control Problems If the remote control does not work Check the operating angle for the remote control is approximately ±22.5°. Make sure there are exhausted. trol and the projector. If so, replace weak batteries in the remote control. 38