User's Guide
Page 28
... surface, so reset by pressing it accidentally is used to manually reset the device. Designated as 1000Base-X SFP ports • 2 Gigabit ports - PowerConnect 3548 Port Description The PowerConnect 3548 device is used to select the unit number. Designated as ...1000Base-T ports • Console port - PowerConnect 3548 Front Panel 10/100 Base-T Ports 1, 3, 5, 7, ...47 System LEDs...
... surface, so reset by pressing it accidentally is used to manually reset the device. Designated as 1000Base-X SFP ports • 2 Gigabit ports - PowerConnect 3548 Port Description The PowerConnect 3548 device is used to select the unit number. Designated as ...1000Base-T ports • Console port - PowerConnect 3548 Front Panel 10/100 Base-T Ports 1, 3, 5, 7, ...47 System LEDs...
User's Guide
Page 29
... the front panel are copper ports. The Stack ID button is marked with even numbers 2-48. The following figure illustrates the PowerConnect 3548 back panel: Figure 2-4. Console Port Hardware Description 29 PowerConnect 3548 Back Panel Console Port RPS Connector Power Connector The back panel contains an RPS connector, console port and power connector. The...) ports are fiber transceivers designated as stacking ports, or used to forward network traffic in a stand-alone device. The default baud rate is used to manually reset the device.
... the front panel are copper ports. The Stack ID button is marked with even numbers 2-48. The following figure illustrates the PowerConnect 3548 back panel: Figure 2-4. Console Port Hardware Description 29 PowerConnect 3548 Back Panel Console Port RPS Connector Power Connector The back panel contains an RPS connector, console port and power connector. The...) ports are fiber transceivers designated as stacking ports, or used to forward network traffic in a stand-alone device. The default baud rate is used to manually reset the device.
User's Guide
Page 37
..., the remain stacking members are not reset. The non-PoE PowerConnect 3524 and PowerConnect 3548 devices have a reset button, located on the front panel, for manual reset of the switch is faulty. If only a member unit is reset. Ventilation System The PowerConnect 3524/P and PowerConnect 3548/P switches with the PoE feature have five built-in fans. The...
..., the remain stacking members are not reset. The non-PoE PowerConnect 3524 and PowerConnect 3548 devices have a reset button, located on the front panel, for manual reset of the switch is faulty. If only a member unit is reset. Ventilation System The PowerConnect 3524/P and PowerConnect 3548/P switches with the PoE feature have five built-in fans. The...
User's Guide
Page 46
... and Identification Panel Each stack device has a unique identifying unit ID that the stand-alone/Master device Console port is illuminated. 46 Installing the PowerConnect 3524/P and PowerConnect 3548/P If the device is a stand-alone unit, the Stack LED is stand-alone. The LED flashes for Member units. During this period, select a specific... that defines the unit's position and function in the stack. The unit ID is indicated by using the Stack ID button. The unit ID is manually configured by the Stack ID LEDs.
... and Identification Panel Each stack device has a unique identifying unit ID that the stand-alone/Master device Console port is illuminated. 46 Installing the PowerConnect 3524/P and PowerConnect 3548/P If the device is a stand-alone unit, the Stack LED is stand-alone. The LED flashes for Member units. During this period, select a specific... that defines the unit's position and function in the stack. The unit ID is indicated by using the Stack ID button. The unit ID is manually configured by the Stack ID LEDs.
User's Guide
Page 50
.... After the initial configuration, the device can skip the Setup Wizard, and manually configure the device through the initial device configuration, and gets the device up and...NOTE: Obtain the following information from the Dell Support website at support.dell.com. The Setup Wizard configures the following : • The Dell™ PowerConnect™ device was never configured before configuring... IP address (optional) • Username and Password 50 Configuring PowerConnect 3524/P and 3548/P The initial device configuration is through which the device is displayed on the terminal...
.... After the initial configuration, the device can skip the Setup Wizard, and manually configure the device through the initial device configuration, and gets the device up and...NOTE: Obtain the following information from the Dell Support website at support.dell.com. The Setup Wizard configures the following : • The Dell™ PowerConnect™ device was never configured before configuring... IP address (optional) • Username and Password 50 Configuring PowerConnect 3524/P and 3548/P The initial device configuration is through which the device is displayed on the terminal...
User's Guide
Page 51
... will continue with a default answer; by entering [ctrl+Z]. If there is not setup for Dell Network Manager) you like to manually configure the switch. You must answer this question within 60 seconds? (Y/N)[Y]Y You can exit the...setup wizard, and enter CLI mode to enter the Setup Wizard (you must respond to the next question to Dell Easy Setup Wizard The Setup Wizard guides you through the initial device configuration. To manage the switch using the ...is a BootP server on setting up and running as quickly as possible. Configuring PowerConnect 3524/P and 3548/P 51
... will continue with a default answer; by entering [ctrl+Z]. If there is not setup for Dell Network Manager) you like to manually configure the switch. You must answer this question within 60 seconds? (Y/N)[Y]Y You can exit the...setup wizard, and enter CLI mode to enter the Setup Wizard (you must respond to the next question to Dell Easy Setup Wizard The Setup Wizard guides you through the initial device configuration. To manage the switch using the ...is a BootP server on setting up and running as quickly as possible. Configuring PowerConnect 3524/P and 3548/P 51
User's Guide
Page 66
...for switching ports. Flow Control The device supports 802.3x Flow Control for ports configured with the half duplex mode. It can be manually set to the same speed and duplex mode. By default, this feature is not set to auto-negotiation, both operate at the ... a NIC that transmission must be enabled per port by default. Back Pressure The device supports back pressure for additional traffic. 66 Configuring PowerConnect 3524/P and 3548/P By default, this feature is enabled per port. It can be halted to advertise its transmission rate, duplex mode and flow control ...
...for switching ports. Flow Control The device supports 802.3x Flow Control for ports configured with the half duplex mode. It can be manually set to the same speed and duplex mode. By default, this feature is not set to auto-negotiation, both operate at the ... a NIC that transmission must be enabled per port by default. Back Pressure The device supports back pressure for additional traffic. 66 Configuring PowerConnect 3524/P and 3548/P By default, this feature is enabled per port. It can be halted to advertise its transmission rate, duplex mode and flow control ...