Dell PowerConnect M6348 Support and Manuals
Get Help and Manuals for this Dell item
View All Support Options Below
Free Dell PowerConnect M6348 manuals!
Problems with Dell PowerConnect M6348?
Ask a Question
Free Dell PowerConnect M6348 manuals!
Problems with Dell PowerConnect M6348?
Ask a Question
Most Recent Dell PowerConnect M6348 Questions
How To Find A Mac Connected To A M6348 Port
(Posted by majkacza 9 years ago)
Stack M6348 How? Step By Step
(Posted by FGakpax 9 years ago)
How To Config Dell M6348 Vlan
(Posted by ladyvanme 9 years ago)
How To Show Mac Address Switch Powerconnect M6348
(Posted by seabafot 9 years ago)
How To Reset Force10 Switch To Factory Default
(Posted by haSPIC 9 years ago)
Dell PowerConnect M6348 Videos
Dell PowerConnect M6348 Price Reduction
Duration: :34
Total Views: 52
Duration: :34
Total Views: 52
Popular Dell PowerConnect M6348 Manual Pages
Command Line Interface Guide - Page 462
... information. • active -
A valid port-channel index. • instance -id - Displays active ports only. • blockedports - Example The following example sets the configuration revision to display the spanning-tree configuration.
www.dell.com | support.dell.com
User Guidelines This command has no user guidelines. A valid Ethernet port number. • port-channel-number -
Command Line Interface Guide - Page 475
... Mode Interface Configuration (Ethernet, Port-Channel) mode
User Guidelines There are enabled for this command. Syntax spanning-tree cost cost no user guidelines for spanning-tree.
475 The port path cost. (Range: 0-200,000,000)
Default Configuration The default cost is 0, which signifies that the cost is automatically calculated based on a port, use the no form of this command. console...
Command Line Interface Guide - Page 488
... bridge is 6 BPDUs. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command to reset the hold count to the default value. www.dell.com | support.dell.com
spanning-tree transmit hold-count
Use the spanning-tree transmit hold-count command to set the maximum number of BPDUs to send (Range: 1-10). Syntax spanning-tree transmit hold count is allowed...
Command Line Interface Guide - Page 536
....dell.com | support.dell.com
console(config-if-1/g2)#dot1x max-users 3
dot1x port-control
Use the dot1x port-control command in Interface Configuration mode to enable the IEEE 802.1X operation on the interface and causes the port to transition to the authorized state without 802.1X-based authentication of the client. • force-unauthorized - Default Configuration The default configuration...
User's Guide - Page 5
... Zone Configuration 109 Summer Time Configuration 110 Clock Detail 112 Reset 113 SNTP Global Settings 115 SNTP Authentication 116 SNTP Server 119
Managing Logs 122 Global Settings 122 RAM Log Table 125 Log File 126 Remote Log Server Settings 127
Setting the Operational Mode 130 Operational Mode Configuration 130
Defining IP Addressing 132 Domain Name Server (DNS 134 Default Domain...
User's Guide - Page 19
... are unavailable.
Simple Network Management Protocol (SNMP) Versions 1, 2, and 3 The system is operating in normal mode. Syslog Syslog is supported.
Time synchronization is composed of backup firmware images. Trivial File Transfer Protocol (TFTP) The PowerConnect M6220/M6348/M8024 switches support boot image, firmware, and configuration upload or download through TFTP. SNMP v1/v2c...
User's Guide - Page 71
... and dates may differ for each switch. Change baud rate 3 - Restore configuration to operational code from the [Boot Menu] prompt, press 1. Operational Code Date: Tue May 26 14:12:20 2009 Uncompressing..... If no problems were encountered during boot. Start operational code 2 - The following output displays an example configuration. To return to factory defaults (delete config files) 11...
User's Guide - Page 75
... Dell PowerConnect
73 Note: After making any configuration changes, the new configuration must be setup when turning up the IP address for configuring the default route
There are two types of configuration: • Initial configuration consists of the switch is designed to guide you may return later to configure Radius or TACACS+.
• Sets up the switch. To save the configuration...
User's Guide - Page 170
... click System > Management Security > TACACS+ in the
CLI Reference Guide: • AAA Commands. TACACS+ Settings The device provide Terminal Access Controller Access Control System (TACACS+) client support. Specify the Enable password. 3. The TACACS+ protocol ensures network security through user names and user-defined
passwords. • Authorization - Click Apply Changes. Defining Enable...
User's Guide - Page 644
..., or select Global to apply the settings to their defaults for each Class of Service. 5.
Select a Trust Mode. 4. Configuring CoS (802.1P) Trust Mode 1. Queues are applied to associate with each Class of Service Open the Mapping Table Configuration page. 2. Select a Queue to the selected interfaces, and the device is updated.
642
Configuring Quality of Service, and the device is...
Getting Started Guide - Page 7
Getting Started Guide
5
Unpacking the Switch
Package Contents
When unpacking each switch, make sure that the following items are included: • One PowerConnect switch • One USB type A-to install, configure, and operate Dell™ PowerConnect™ M6348 systems. For more information, see the Hardware Owner's Manual, which is available on documentation and firmware. Site ...
Getting Started Guide - Page 17
...the CLI Reference Manual for details on a port enabled for smaller stacks. User Controls
Use the following CLI commands to /from the stack. Insertion and Removal of twelve switches, less time for stacking, the switch will not be re-elected, unless the Master Switch was saved for the new Stack ID is applied to another switch in stacking mode. A switch can insert and remove switches to...
Getting Started Guide - Page 193
... Manual movemanagement reload member set description switch priority switch renumber stacking show stack-port
show stack-port counters show stack-port diag show switch
show supported switchtype
IP DHCP
CLI M6348 8024ו ,F8024 CLI -
Reference Guide...
Configuration Guide - Page 140
exit
Set the CoS queue configuration for the (presumed) egress interface 1/g5 such that each of queues 1, 2, 3 and 4 get a minimum guaranteed bandwidth of DiffServ is to support Voice over IP (VoIP). interface ethernet 1/g5 cos-queue min-bandwidth 0 25 25 25 25 0 0 exit
exit
DiffServ for the departmental traffic through the assign-queue attribute. It...
White Paper - Page 11
... is no saved configuration, then the default configuration of the selected mode is applied.
• Simple mode allows the user to create Aggregation Groups (see any one for Simple mode and another for Normal mode.
You can change the operational mode from Simple to Normal and vice versa.
• Operational mode is set to Normal mode on resetting the configuration to all the member...
Dell PowerConnect M6348 Reviews
We have not received any reviews for Dell yet.