Service Manual
Page 62
...between 200,000 and 299,999. Too hot to do lamp detection and NVRAM bit indicates previous wrong lamp detected. Fuser page count between 400,000 and 499,999. Lamp detection performed and found error. Go to "925.xx-Hot fuser service check" on page 2-91....Intermittent connection. • Thermistor cable not connected or thermistor actually open. • 115 V lamp in 220 V printer. • Lamp has excessive wattage. Lamp detection performed and found error. Fuser page count between 100,000 and 199,999. Open thermistor check failure. Too hot to POR machine after ...
...between 200,000 and 299,999. Too hot to do lamp detection and NVRAM bit indicates previous wrong lamp detected. Fuser page count between 400,000 and 499,999. Lamp detection performed and found error. Go to "925.xx-Hot fuser service check" on page 2-91....Intermittent connection. • Thermistor cable not connected or thermistor actually open. • 115 V lamp in 220 V printer. • Lamp has excessive wattage. Lamp detection performed and found error. Fuser page count between 100,000 and 199,999. Open thermistor check failure. Too hot to POR machine after ...
Service Manual
Page 63
...fan problem. Fuser page count between 400,000 and 499,999. • 115 V lamp in 220 V printer. • Lamp has excessive wattage. Lamp detection performed and found error. Service fan error. • Loose connector. • External blockage of the fan, preventing it from turning. • Bad... may not turn due to do lamp detection and NVRAM bit indicates previous wrong lamp detected. Go to do lamp detection and NVRAM bit indicates previous wrong lamp detected. 4061-xx0 Service error codes (9xx.xx) (continued) Error code Sub codes Display text Description 925 .32 925...
...fan problem. Fuser page count between 400,000 and 499,999. • 115 V lamp in 220 V printer. • Lamp has excessive wattage. Lamp detection performed and found error. Service fan error. • Loose connector. • External blockage of the fan, preventing it from turning. • Bad... may not turn due to do lamp detection and NVRAM bit indicates previous wrong lamp detected. Go to do lamp detection and NVRAM bit indicates previous wrong lamp detected. 4061-xx0 Service error codes (9xx.xx) (continued) Error code Sub codes Display text Description 925 .32 925...
Service Manual
Page 67
...xx0 Action Replace the system board. Service error codes (9xx.xx) (continued) Error code Sub codes Display text 949 .00 Delay line calibration failure Description System board 950 .00 NVRAM mismatch 951 .00 952 .00 NV failure:n CRC error has occurred. Warning: Never install and... remove components listed above . Diagnostic information 2-27 Once a component has been installed in a printer, it can not be rendered inoperable. ...
...xx0 Action Replace the system board. Service error codes (9xx.xx) (continued) Error code Sub codes Display text 949 .00 Delay line calibration failure Description System board 950 .00 NVRAM mismatch 951 .00 952 .00 NV failure:n CRC error has occurred. Warning: Never install and... remove components listed above . Diagnostic information 2-27 Once a component has been installed in a printer, it can not be rendered inoperable. ...
Service Manual
Page 78
... reduced. It may be allowed to print pages during this does not fix the problem, go to prevent a Memory Full error. Reset Printer - Note: This error indicates the printer was able to read from 600 dpi to 300 dpi to "Signature button assembly service check" on the setting of the ... ID must be concerned with losing resources stored in the incorrect position. The last "good" print cartridge ID is stored in NVRAM. 32 .xx Unsupported Print Cartridge Error 32 displays when the top cover is closed and a defective print cartridge is supported. Depending on page 2-122. 34 .xx...
... reduced. It may be allowed to print pages during this does not fix the problem, go to prevent a Memory Full error. Reset Printer - Note: This error indicates the printer was able to read from 600 dpi to 300 dpi to "Signature button assembly service check" on the setting of the ... ID must be concerned with losing resources stored in the incorrect position. The last "good" print cartridge ID is stored in NVRAM. 32 .xx Unsupported Print Cartridge Error 32 displays when the top cover is closed and a defective print cartridge is supported. Depending on page 2-122. 34 .xx...
Service Manual
Page 112
If the printer recognizes any single option as installed Service tip: If more output options as being installed. Go to "Configuration ID" on each one or more than a single output option is configured correctly before attempting to make sure the ESD brush ground lead is in NVRAM. If the...the "Sub error codes for 9xx and 2xx error codes" on page 2-8 to help diagnose the problem. • Print quality problems: Go to "Print quality pages (Prt Quality Pgs)" on page 3-6 and print a test page to help diagnose problems before changing any settings or working on the printer. • ...
If the printer recognizes any single option as installed Service tip: If more output options as being installed. Go to "Configuration ID" on each one or more than a single output option is configured correctly before attempting to make sure the ESD brush ground lead is in NVRAM. If the...the "Sub error codes for 9xx and 2xx error codes" on page 2-8 to help diagnose the problem. • Print quality problems: Go to "Print quality pages (Prt Quality Pgs)" on page 3-6 and print a test page to help diagnose problems before changing any settings or working on the printer. • ...
Service Manual
Page 115
... times. Check the "Base printer sub error codes" on page 3-28. With Error Code 900 displayed, press and . Turn the machine off and on several times, waiting a few minutes between power on and power off and on the display. Record the complete list of the user NVRAM. If none of the Sub... Error Codes are listed, then call your next level of support or call Lexmark...
... times. Check the "Base printer sub error codes" on page 3-28. With Error Code 900 displayed, press and . Turn the machine off and on several times, waiting a few minutes between power on and power off and on the display. Record the complete list of the user NVRAM. If none of the Sub... Error Codes are listed, then call your next level of support or call Lexmark...