Owner's Manual
Page 6
...switch may be engaged to complete each step. Closing Garage Door (Down Limits) 1 Lift the door open by hand until the shuttle/bullet engages the carriage on the rail. 4 Press and hold the down arrow button (-) until the long LED comes on the Powerhead, you see two solid red or flashing... have 30 seconds to the beginning of the step and start over. Severe damage to the opener can restart as many times as necessary to carriage BEFORE setting limits. PROGRAM SET + NOTE: If shuttle/bullet has NOT been engaged to property. • DO NOT operate this unit from wall console ...
...switch may be engaged to complete each step. Closing Garage Door (Down Limits) 1 Lift the door open by hand until the shuttle/bullet engages the carriage on the rail. 4 Press and hold the down arrow button (-) until the long LED comes on the Powerhead, you see two solid red or flashing... have 30 seconds to the beginning of the step and start over. Severe damage to the opener can restart as many times as necessary to carriage BEFORE setting limits. PROGRAM SET + NOTE: If shuttle/bullet has NOT been engaged to property. • DO NOT operate this unit from wall console ...
Owner's Manual
Page 7
... PROGRAM - + ET G999-393 Manual-ScrewBeltChain-EN indd 7 The UP (open , then release. BOTH DOOR LIMITS ARE NOW PROGRAMMED. 7 7/13/12 10 17 AM Watch carriage as it approaches the power head to avoid contact with garage door closed ) limit is programmed. HOLD Opening Garage Door (Up Limits) NOTE: Beginning with...
... PROGRAM - + ET G999-393 Manual-ScrewBeltChain-EN indd 7 The UP (open , then release. BOTH DOOR LIMITS ARE NOW PROGRAMMED. 7 7/13/12 10 17 AM Watch carriage as it approaches the power head to avoid contact with garage door closed ) limit is programmed. HOLD Opening Garage Door (Up Limits) NOTE: Beginning with...
Owner's Manual
Page 15
... Doors Attaching door bracket to door 1 Using bracket, mark holes on door as high as possible, preferably top edge. 2 Secure bracket with 5/16" x 2" or 5/16" x 4-1/2" carriage bolts and nuts or drill 1/8" pilot holes and secure with clevis pin and cotter pin. Door bracket Cotter pin Straight door arm G999-393 Manual...
... Doors Attaching door bracket to door 1 Using bracket, mark holes on door as high as possible, preferably top edge. 2 Secure bracket with 5/16" x 2" or 5/16" x 4-1/2" carriage bolts and nuts or drill 1/8" pilot holes and secure with clevis pin and cotter pin. Door bracket Cotter pin Straight door arm G999-393 Manual...
Owner's Manual
Page 16
...from another Safe-T-Beam® unit (for obstruction. - This indicates the system is closed. Verify wire routing from STBs to release door carriage assembly from children. 3. Door should remain stationary or move freely and smoothly. • Raise door manually about 3' to 4' feet and...PROPERLY BALANCED. NEVER let children operate or play with a 1-1/2" high object (or a 2" x 4" board laid flat) at : 1-800-35-GENIE or visit www.geniecompany.com Important Safety Instructions WARNING TO REDUCE THE RISK OF SEVERE injury or death, READ AND FOLLOW ALL INSTRUCTIONS. 1. B. Check...
...from another Safe-T-Beam® unit (for obstruction. - This indicates the system is closed. Verify wire routing from STBs to release door carriage assembly from children. 3. Door should remain stationary or move freely and smoothly. • Raise door manually about 3' to 4' feet and...PROPERLY BALANCED. NEVER let children operate or play with a 1-1/2" high object (or a 2" x 4" board laid flat) at : 1-800-35-GENIE or visit www.geniecompany.com Important Safety Instructions WARNING TO REDUCE THE RISK OF SEVERE injury or death, READ AND FOLLOW ALL INSTRUCTIONS. 1. B. Check...
Owner's Manual
Page 17
.../Close Travel Limit Performing all eleven (11) Limits/Force setting steps (see pages 6-8) erases previous Limits/Force settings. Reconnect power to carriage. To disengage shuttle from a ladder or step stool. • When replacing light cover, make sure wires are programmed. Replace battery.... 3. CORRECTIVE MAINTENANCE Changing Light Bulbs WARNING • Use extreme caution when working from carriage, pull down and toward the door. Door will not close the door automatically unless the Safe-T-Beam® System is engaged to...
.../Close Travel Limit Performing all eleven (11) Limits/Force setting steps (see pages 6-8) erases previous Limits/Force settings. Reconnect power to carriage. To disengage shuttle from a ladder or step stool. • When replacing light cover, make sure wires are programmed. Replace battery.... 3. CORRECTIVE MAINTENANCE Changing Light Bulbs WARNING • Use extreme caution when working from carriage, pull down and toward the door. Door will not close the door automatically unless the Safe-T-Beam® System is engaged to...
Owner's Manual
Page 21
... to the store. See pages 10-11. Erase all remotes. • Replace remote battery with the garage door hardware or springs, contact The Genie Company at 1-800-35GENIE. See page 17. • Eliminate possible competing signals (satellite radio, FiOS® TV). OR Safe-T-Beam® ...: Press and hold the wall console button until door is completely closed. • Check for interference from remote. • Make certain carriage is closed . • Check if limits are properly set . Door starts down , then STOPS before it is engaged into outlet used for...
... to the store. See pages 10-11. Erase all remotes. • Replace remote battery with the garage door hardware or springs, contact The Genie Company at 1-800-35GENIE. See page 17. • Eliminate possible competing signals (satellite radio, FiOS® TV). OR Safe-T-Beam® ...: Press and hold the wall console button until door is completely closed. • Check for interference from remote. • Make certain carriage is closed . • Check if limits are properly set . Door starts down , then STOPS before it is engaged into outlet used for...
Owner's Manual
Page 22
...? Check door spring, track, rollers, hinges and fixtures. Normal speed for a one -piece door is lowest speed setting. • If carriage travel is in UP or DOWN travel. Remote NOT programmed. Program remote, see page s 6-7. Door contact in good repair. Remove obstruction, recheck... and balanced. • Be sure opener is less than 6-feet, opener configures programming for one -piece door. • Contact The Genie Company at 1-800-35GENIE concerning door speed. No response from unit. Contact a trained door system technician. Component failure. Safe-T-Beam®...
...? Check door spring, track, rollers, hinges and fixtures. Normal speed for a one -piece door is lowest speed setting. • If carriage travel is in UP or DOWN travel. Remote NOT programmed. Program remote, see page s 6-7. Door contact in good repair. Remove obstruction, recheck... and balanced. • Be sure opener is less than 6-feet, opener configures programming for one -piece door. • Contact The Genie Company at 1-800-35GENIE concerning door speed. No response from unit. Contact a trained door system technician. Component failure. Safe-T-Beam®...