Genie PowerMax 1200 Support Question
Genie PowerMax 1200 Support Question
Find answers below for this question about Genie PowerMax 1200.Need a Genie PowerMax 1200 manual? We have 1 online manual for this item!
Question posted by eglosser on March 30th, 2013
Powermax 1200 Carriage Assembly
I have a powermax 1200 carriag that I had to remove from the screw drive. Two parts came out of it. One looks like some sort of leaf spring and I can't figure out where it goes, Please help!!!!!
Current Answers
Related Genie PowerMax 1200 Manual Pages
Owner's Manual - Page 1
... Car2U is a registered trademark of Johnson Controls Technology Company. Need help or have questions?
GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
SCREW/BELT/CHAIN DRIVES
OPERATION & MAINTENANCE MANUAL
Includes INTELLICO®DE 2 Remote Control.
Safe...
Owner's Manual - Page 2
...Function 3
F3eatures
Safety 4 Opener 4
R4equired5Progra6mming
Introduction 5 Overview of Powerhead Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall... entsprechen, welche
von den Bestimmungen der USA und Kanadas abweichen.
5
6
7 Need help or have questions? Ninguna garantía
se da que cumplan con todas las reglamentaciones ...
Owner's Manual - Page 3
...door spring parts are NOT pinched or near moving . DO NOT allow children to play with the help of springs...Opener must be made by a trained door system technician, using proper tools and instructions.
• Remove all ropes, and disable all
moving objects, springs... Garage doors are large, heavy objects that move with the door opener. This symbol alerts you to cables, spring assembly,...
Owner's Manual - Page 4
... if anything passes through the garage. Turns ON when door is used. The door opener responds to the full open /close the
door, it will turn ON when motion is interrupted by continuously changing the access code each new code only once. 2 Features
Begin here only after completing assembly and installation of opener.
Lights will not allow manual...
Owner's Manual - Page 5
... to synch with additional remote control devices, wall consoles, keypads, and the powerhead.
3.
Remote Programs (Default menu) - These show you how to program your Genie garage door opener is used to program functions. NOTE: The 3 programming buttons are unlikely to need to follow to set up your remote control devices (remotes, wall console...
Owner's Manual - Page 6
...-Lock switch may be engaged to the beginning of time and must go back to carriage BEFORE setting limits.
PROGRAM
SET
+
HOLD
1
2 1
2 Press and hold the down arrow button (-) until
garage door is ON. Closing Garage Door (Down Limits)
1 Lift the door open by hand until the long LED comes on floor, then release. PROGRAM
PROGRAM
SET...
Owner's Manual - Page 7
... the long LED light comes on blue (round LED remains off ).
Watch carriage as it approaches the power head to avoid contact with garage door closed ) limit is programmed.
8 Press and hold the up arrow button (+) for
2 seconds until door
is fully open, then release. PROGRAM
PROGRAM
- +
SET
The DOWN (closed is programmed. PROGRAM
SET...
Owner's Manual - Page 8
... Control Button Controls door opener lights from inside garage.
8
Series III Wall Consoles with this button to turn Sure-Lock™ OFF. When Sure-Lock™ is ON, the powerhead cannot be activated by the wall console or a remote. • Press and hold for 5 seconds (or until red light goes off
Open/Close Button Use...
Owner's Manual - Page 9
... and ADJUSTMENTS, Regular Maintenance, pages 16-19.
9
Repeat this manual (pages 18-19).
10 Open and close your garage door. For further help, refer to open and close the garage door for the first time automatically sets the Force needed until door passes the Contact Reverse Test. 3 Required Programming
Force and Speed Control
These controls are factory...
Owner's Manual - Page 11
...as necessary for additional Remotes. To program the same Remote for three door openers.
NOTE: For Car2U and HomeLink, park the car outside the garage with the ignition key in the HomeLink® instruction manual.
19 ...to Genie mode. Each Remote can be programmed for other garage door openers, repeat the steps above using one of the other two Remote buttons.
PROGRAM
SET
-
Owner's Manual - Page 12
... . Opener LEDs will run. Door opener will turn o . 5. When the door has stopped moving, pressing on any key will stop fully open or closed.
To erase, follow the steps in motion. Press and hold Program Set key for 2 seconds. (The round LED turns blue and then goes o . Enter your new PIN (3-8 characters). 4. Opener LEDs will activate door until...
Owner's Manual - Page 13
...is pressed the round LED will flash blue but will not activate the door opener. PROGRAM
- +
3 Press up arrow button (+) and down arrow...LEDs flash blue and then go OFF. NOTE: The garage door opener will clear ALL programmed Remotes and wireless Keypads.
G999-...(continued next page) 13
7/13/12 10 17 AM
Your opener will no longer recognize any signal received from the Powerhead memory...
Owner's Manual - Page 14
... ON).
The LED color displayed on the Remote turn the RED LED on your Genie® instructions for this Intellicode® 1 model of Genie® garage door openers .The default Intellicode® 2 setting must be changed to Intellicode® 1. (Follow these same steps to change Intellicode® 1 back to Intellicode® 2.)
NOTE: The...
Owner's Manual - Page 16
... the console.
Door Balance (Spring Tension) Perform the check as follows:
1. Start the door closing. 2. Pass an object through the beam. The door MUST reverse on the floor. A.
This indicates the system is completely closed , pull manual emergency release handle DOWN and let go to release door carriage assembly from door to the fully open . The door should stop and...
Owner's Manual - Page 17
...engaged to door opener. • Open powerhead light cover. • Remove light bulb(s). • Replace light bulb(s).
- DO NOT use light bulbs with a CR 2032 coin cell battery. 1. Close powerhead light cover. 2.
To disengage shuttle from carriage, pull relaese handle down on relaese hanfle.
Replace battery. 3. Screw Drive
Opener
Belt/Chain Drive
Opener
Disengaged
Engaged...
Owner's Manual - Page 19
...)
Sun
Red Green
LED
LED
One Door Garage
Green LED
Red Red LED LED
Two Door Garage
Green LED
Green
Red Red
Green Green
Red
LED
LED LED
LED LED
LED
Three Door Garage
Single Garage Door • Determine which side of door components and tracks.
Note: PowerLift® 900, GPower™ 900 openers DO NOT have the option to...
Owner's Manual - Page 21
...from remote.
• Make certain carriage is closed . • Check for reversed, broken or cut insulation and short wires. See page 17. • Reposition door opener antenna.
• Remote LED does not come ON with the garage door hardware or springs, contact
The Genie Company at 1-800-35GENIE. replace battery. Door opener starts for normal operation.
Check connections...
Owner's Manual - Page 22
... are tight. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is lowest speed setting. • If carriage travel .
Program remote, see page 10. No response from unit. Check power supply.
Safe-T-Beam® physical obstruction.
Check alignment of door. Check door spring, track, rollers, hinges and fixtures. Contact...
Owner's Manual - Page 23
... original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ("Product"), subject to Seller at purchaser's expense) Seller may use new or reconditioned parts, or a new or reconditioned Product of the same or...
Owner's Manual - Page 24
....
can open door without remote • Lighted keypad with flip-up cover • Controls up to 3 openers • Large, easy to door - Garage Door Opener Accessories
Looking for activation...1200 and 1000 Models)
• Sleek and compact design
• Beeps and flashes green when garage door closes. enables safe parking in garage
Universal Wall Push Button • Easy to mount inside garage...
Similar Questions
The Garage Door Stopped Working,one Sensor Is Green The Other Is Blinking Red,
i tried re aligning the sensor with no luck. Any suggestions?Thanks Mar
i tried re aligning the sensor with no luck. Any suggestions?Thanks Mar
(Posted by Bigassneal 7 years ago)
Garage Door Opener Not Working
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
(Posted by scanty5 9 years ago)
Genie Garage Door Opener Powermax 1200 Will Not Work
(Posted by EpiNiaddisk 9 years ago)
Garage Door Does Not Function At All.
Unit has power. Unit responds to both remotes and keypad with 4 clicks (one set and then another) bu...
Unit has power. Unit responds to both remotes and keypad with 4 clicks (one set and then another) bu...
(Posted by tysonlemka 10 years ago)
Where Is The Learn Code Button Situated On The 3060l-07 Genie Garage Door Opener
Where is the learn code button situated on the 3060L-07 Genie garage door opener. Trying to intregat...
Where is the learn code button situated on the 3060L-07 Genie garage door opener. Trying to intregat...
(Posted by katiaella 10 years ago)