IBM RS6000 - 7026 - H70 Support and Manuals
Get Help and Manuals for this IBM item
Most Recent IBM RS6000 Questions
Rs6000 -7024 Error On Led
Getting a error code 021600964 on LED display IBM RS6000 7024 SERVER.
Getting a error code 021600964 on LED display IBM RS6000 7024 SERVER.
(Posted by tiripanoshamba 13 years ago)
IBM RS6000 Videos
RS/6000 Startup Chime
Duration: :14
Total Views: 1,655
Duration: :14
Total Views: 1,655
Selling Used Tested, Working IBM RS-6000 43p-140 Server on eBay
Duration: 1:27
Total Views: 43
Duration: 1:27
Total Views: 43
IBM RS6000 #10 - AIX 5.1 Graphical Install Part 4
Duration: 21:49
Total Views: 848
Duration: 21:49
Total Views: 848
IBM RS6000 #3 - IBM P70 CRT Monitor
Duration: 4:16
Total Views: 295
Duration: 4:16
Total Views: 295
Popular IBM RS6000 Manual Pages
Service Guide - Page 3
... Analysis Procedures (MAPs 2-35 MAP 2010: SSA Hot-Swap Disk Drive-Start 2-37
Chapter 3. viii Canadian Department of Communications Compliance Statement viii VCCI Statement viii Radio Protection for RS/6000 7025 F50 Series 1-9 Specifications 1-10 Power Cables 1-12 Service Inspection Guide 1-13
Chapter 2. Contents
Communications Statements vii Federal Communications Commission (FCC...
Service Guide - Page 25
Typical Boot Sequence for RS/6000 7025 F50 Series
After the A/C power is pressed. Built-In-Self-Test (BIST)
The Service Processor initiates Built-In-Self-Test (BIST) on the Central Electronics Complex (CEC) chips when the POWER Button is turned on, the System Support Controller (SSC) startup begins, and releases reset to start the On-line...
Service Guide - Page 31
..." in fixing the problem.
The AIX error log and SMIT are only available when diagnostics are run Online Diagnostics in the IBM RS/6000 Diagnostic Information for Multiple Bus Systems.
You need to enable system startup. Online Diagnostics perform additional functions, compared to "MAP 410: Repair Checkout" in Service Mode. If more than eight digits are location codes that the...
Service Guide - Page 36
... Setup Menu and set by the customer or you are asked to the Surveillance Setup Menu and disable surveillance. It is a good idea to MAP 0020 in the IBM RS/6000 Diagnostic Information for restoration before proceeding (see Service Processor System Information Menu). From the System Power Control Menu, go to examine that error log before you diagnose and service the system...
Service Guide - Page 47
... Setup Menu, go to examine that error log before you should make notes of your interest. If you disable them .
2. It is installed and connected to the icons (graphic display) or device mnemonics (ASCII terminal) that a CD-ROM drive is a good idea to the Serial Port Selection Menu and disable call-out on a minimally-configured system. If a failure...
Service Guide - Page 75
... Codes. system locked.
The Machine Model is enabled.
1. Retry installing the password.
Consult the system's User's Guide for errors 2BA00050, 2BA00051. Turn off , then turn on the system unit, then enter the password correctly.
Replace battery, restore NVRAM data (passwords, startup data).
2. If no tampering evident:
1.
Action / Possible Failing FRU
Contact you service support...
Service Guide - Page 80
... normal system usage. Firmware Error Codes. Data corruption detected, some data partitions may have been preserved.
Action / Possible Failing FRU
NVRAM problem resolution:
1. boot device list) information has been lost, the system may need to Action under error code 25A80xxx. Refer to Action under error code 25A80xxx. Refer to Action under error code 25A80xxx.
3-8 Service Guide...
Service Guide - Page 296
... personnel will respond to problem calls from your server.
You may be set or change the telephone numbers for :
Service Center Telephone Number: - The telephone number of the local system support provider's computer. Customer System Telephone Number: -
The Service Processor allows setting or changing telephone numbers for reporting a system failure. The telephone number of the...
Service Guide - Page 327
...Enable responses (Numeric), # Limit response codes. # Confirm commands successful. # Set AutoAnswer OFF # Confirm command successful. When used as required.
# 7=busy; 6=no dial tone; 4=error; 3=no op to maintain program synchronization
#
when modem may/will work for early vintage # modems which respond to your modem manual. # # ᑍ Trademark of IBM # # US Government Users Restricted...
Service Guide - Page 329
.... Refer to your modem # manual. # # ᑍ Trademark of IBM # # US Government Users Restricted Rights - Use, duplication or # disclosure restricted by GSA ADP Schedule Contract with IBM Corp. # # # If the modem has configuration switches, they should be set to command mode S =2 Answer on second ring
# H Hang-up
X = Limit modem response codes
#
T = Tone mode. Select profile # Ignore modem...
Service Guide - Page 331
...setup Z or Z is preferred for modems with IBM Corp. # # # If the modem has configuration switches, they should be set up
X = Limit modem response codes
#
T = Tone mode. Property of modems:
# 16, 15, 12, 1 , 5 and 1 are common responses from Call Home setup...When used as required.
# 7=busy; 6=no dial tone; 4=error; 3=no op to maintain program synchronization
#
when modem may/will ...
Service Guide - Page 334
.... Sample File modem_f0.cfg
# # COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP F # # FUNCTIONS: Modem configuration file for modems with extended (&) commands. Select profile # Ignore modem response. # Initialize modem: Echo OFF, # Enable responses (Numeric), # Limit response codes. # Confirm commands successful. # Set AutoAnswer OFF # Confirm command successful. # Detect carrier and DTR...
Service Guide - Page 337
... File modem_f1.cfg
# # COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP F1 # # FUNCTIONS: Modem configuration file for modems with extended (&) commands and which do not work # properly with IBM Corp. # # # If the modem has configuration switches, they should be set up
X = Limit modem response codes
#
T = Tone mode. For early vintage modems, setup Z or Z is for many recent Hayes...
Service Guide - Page 348
... processor serial port
selection B-17 service processor serial port speed
setup B-18 service processor setup B-8 service processor system
information B-13 service processor system power
control B-12 service processor telephone
setup B-18 Set Service Mode service aid 3-67 SSA Service Aids 3-65 support menus
service processor menus B-2 service processor service
aids B-2 SMS B-2
X-4 Service Guide
Service Guide - Page 351
... setup C-1 service processor setup checklist C-1 service processor test C-1 service provider B-19 service request numbers (SRNs)
description of A-3 software and microcode errors A-5 table A-6 Set Service Mode service aid 3-67 software and microcode errors A-5 sp checklist C-1 SP checkpoints 3-29 sp installation checklist C-1 SP operational phases E-1 sp setup C-1 sp test C-1 specifications, system...
IBM RS6000 Reviews
We have not received any reviews for IBM yet.