Dell PowerConnect 7024 Support and Manuals
Get Help and Manuals for this Dell item
View All Support Options Below
Free Dell PowerConnect 7024 manuals!
Problems with Dell PowerConnect 7024?
Ask a Question
Free Dell PowerConnect 7024 manuals!
Problems with Dell PowerConnect 7024?
Ask a Question
Most Recent Dell PowerConnect 7024 Questions
Dell Powerconnect 7024 How To Access Usb
(Posted by fothiwa 9 years ago)
How To Export Configuration Dell Powerconnect 7024
(Posted by 8318buck 10 years ago)
Dell PowerConnect 7024 Videos
Dell PowerConnect 7024 $1950 Price Reduction
Duration: :34
Total Views: 49
Duration: :34
Total Views: 49
Popular Dell PowerConnect 7024 Manual Pages
User Manual - Page 5
... 63
Power over Ethernet (PoE) Plus Features 63 Power Over Ethernet (PoE) Plus Configuration 63 PoE Plus Support 64
Switching Features 64 Flow Control Support (IEEE 802.3x 64 Head of Line Blocking Prevention 64 Jumbo Frames Support 64 Auto-MDI/MDIX Support 64 VLAN-Aware MAC-based Switching 65 Back Pressure Support 65 Auto Negotiation 65 Broadcast Storm Control 65 Port Mirroring...
User Manual - Page 56
... IP Management When multiple switches are running an older version of the firmware than the other stack members, the firmware on page 135.
The stack operates and is added to 576 front-panel ports, if all units in the PowerConnect 7000 Series as long as all switches are connected together through the management interface (Web, CLI, or SNMP) of switches, see "Managing a Switch Stack...
User Manual - Page 90
... removed or replaced.
Ventilation System
Three fans cool the PowerConnect 7024, PowerConnect 7024F, and PowerConnect 7048. From your remote management system, you can set the LED to blink to removing the module itself. The additional external power supply (PowerConnect MPS1000) allows all 48 ports of PoE, or 24 ports of PoE. Power must not be connected prior to enable the switch locator...
User Manual - Page 847
...over an IPv4 infrastructure.
After you configure an IP address, routing is no IP address is configured, and DHCP is disabled. Enabled Enabled
When you create a loopback interface, the default values are similar to those of VLAN routing interfaces, as Table 30-1 shows. Most interface configuration parameters are configured. the show interface loopback command lists all these features and...
User Manual - Page 905
...)#ip route default 192.168.50.2
Configuring IP Routing
905 This command also enables IP routing on the switch.
console(config)#interface vlan 10 console(config-if-vlan10)#ip address 192.168.10.10 255.255.255.0 console(config-if-vlan10)#exit
3 Assign an IP address to VLAN 10. console#configure console(config)#ip routing
2 Assign an IP address to VLAN 20.
console#configure console...
User Manual - Page 909
... selected from the Web interface or specified by a service VLAN ID (S-VID), which a service provider uses to identify a customer's traffic while traversing the provider network to multiple remote sites. This allows applications to reach servers on routing interfaces.
Discard relay entries may configure relay entries that these entries match packets with any UDP port number. If the...
User Manual - Page 1198
... on VLAN routing interfaces and to configure IGMP on the switch and on the interface. The query interval determines how fast IGMP HostQuery packets are transmitted on this interface.
Enable IGMP on this interface. Set the version of queries sent out on startup -at startup on a subnet. Set the number of IGMP for the interface. Command configure ip igmp interface vlan vlan-id
ip...
User Manual - Page 1203
...: 0-65535) to wait between sending PIM hello messages on VLAN routing interfaces and to Privileged EXEC mode. Configuring and Viewing PIM-DM for IPv4 Multicast Routing
Beginning in Privileged EXEC mode, use the following commands to configure PIM-DM for IPv4 multicast routing on the switch and on the interface.
ip pim hello-interval seconds Specify the number of information about...
User Manual - Page 1204
... pim
View system-wide PIM-DM information.
Configuring and Viewing PIM-DM for IPv6 Multicast Routing
Beginning in Privileged EXEC mode, use the following commands to configure PIM-DM for IPv6 multicast routing on the switch and on the interface. ipv6 pim dense
Enable PIM-DM on the interface.
show ipv6 pimdm neighbor [interface vlan vlan-id | all]
View a summary or all...
User Manual - Page 1205
... the first 24 bits of a mask that is to be ANDed with the higher IP address is called.
ip pim sparse
Enable PIM-SM as a bootstrap router (BSR).
• vlan-id -
A valid VLAN ID.
• group-address - ip pim bsr-candidate vlan vlan-id hash-mask-length [priority]
Configure the switch to announce its candidacy as the multicast routing protocol on VLAN routing interfaces and...
User Manual - Page 1207
...
ipv6 pim register-threshold threshold
Purpose
Enter global configuration mode.
Managing IPv4 and IPv6 Multicast
1207 View the bootstrap router (BSR) information. Enable PIM-SM as the multicast routing protocol on VLAN routing interfaces and to view PIM-SM information.
Command show ip pim rphash groupaddr
show ip pim bsr show ip pim rp mapping
Purpose
View the RP router...
User Manual - Page 1210
... information on VLAN routing interfaces and to view DVMRP information. ip dvmrp
Enable DVMRP on the interface. vlan vlan-id]
show ip dvmrp neighbor View neighbor information for an interface. interface vlan vlan-id
Enter Interface Configuration mode for the specified interface. This value is used in Privileged EXEC mode, use the following commands to configure DVMRP on the switch and on...
User Manual - Page 1211
...8226; Configuring Multicast VLAN Routing With IGMP and PIM-SM • Configuring DVMRP
Configuring Multicast VLAN Routing With IGMP and PIM-SM This example describes how to control the multicast subscriptions within each VLAN. The configuration in this example takes place on the VLAN interfaces to configure a PowerConnect switch with two VLAN routing interfaces that route IP multicast traffic...
User Manual - Page 1224
..., 432
1224
Index
web-based configuration, 436
ISDP and CDP, 55 CLI configuration, 678 configuring, 679 enabling, 679 example, 683 understanding, 659 web-based configuration, 663
J
jumbo frames, 64
L
LACP adding a LAG port, 828 CLI configuration, 833 web-based configuration, 825
LAG and STP, 822 CLI configuration, 830 defaults, 823 examples, 834 guidelines, configuration, 823 interaction with...
Getting Started Guide - Page 7
...RA)
NOTE: The PowerConnect 7048R (PC7048R/PC7048R-RA) is the air-flow direction. For information about the Dell PowerConnect 7000 Series switches, including how to configure and monitor switch features, see the User's Configuration Guide, which is available on your User Documentation CD, or check the Dell Support website at support.dell.com for the latest updates on documentation and firmware.
Dell PowerConnect 7024 Reviews
We have not received any reviews for Dell yet.