Datasheet
Page 2
Wireless N Hot Spot Access Point TEW-636APB (V1.0R) SPECIFICATIONS Hardware Standards Interface Reset Button Config Button LED Indicator Power Adapter Dimension (L x W x H) Weight Temperature Humidity ...Wireless: IEEE 802.11b, IEEE 802.11g, IEEE 802.11n (draft 2.0) • 1 x 10/100Mbps Auto-MDIX LAN Port • Reset To Factory Default Settings • Reserved For WPS Function Use • WPS, Power, WLAN, Status • 12V DC, 1A External Power ...72dBm (Typical) @ 54Mbps • 802.11n (Draft 2.0) : -70dBm (Typical) with HT20 & HT40 • 1~ 11 (US), 1~13 (EU) TEW-636APB rev:08.15.2008
Wireless N Hot Spot Access Point TEW-636APB (V1.0R) SPECIFICATIONS Hardware Standards Interface Reset Button Config Button LED Indicator Power Adapter Dimension (L x W x H) Weight Temperature Humidity ...Wireless: IEEE 802.11b, IEEE 802.11g, IEEE 802.11n (draft 2.0) • 1 x 10/100Mbps Auto-MDIX LAN Port • Reset To Factory Default Settings • Reserved For WPS Function Use • WPS, Power, WLAN, Status • 12V DC, 1A External Power ...72dBm (Typical) @ 54Mbps • 802.11n (Draft 2.0) : -70dBm (Typical) with HT20 & HT40 • 1~ 11 (US), 1~13 (EU) TEW-636APB rev:08.15.2008
User's Guide
Page 8
...and restore ALL settings to Factory Defaults. When pressed and released, the Wireless Access Point will reboot (restart). • Reset to the factory default values. Release the Reset Button. Use a standard LAN cable (RJ45 connectors) to connect this port to a 10BaseT or 100BaseT hub/switch on your.... 5 To Clear All Data and restore the factory default values: 1. Hold the Reset Button until the Status (Red) LED blinks TWICE, usually more than 5 seconds. 2. Rear Panel Introduction WPS Button LAN Reset Button Power port Figure 3: Rear Panel Push the WPS button on the device and ...
...and restore ALL settings to Factory Defaults. When pressed and released, the Wireless Access Point will reboot (restart). • Reset to the factory default values. Release the Reset Button. Use a standard LAN cable (RJ45 connectors) to connect this port to a 10BaseT or 100BaseT hub/switch on your.... 5 To Clear All Data and restore the factory default values: 1. Hold the Reset Button until the Status (Red) LED blinks TWICE, usually more than 5 seconds. 2. Rear Panel Introduction WPS Button LAN Reset Button Power port Figure 3: Rear Panel Push the WPS button on the device and ...
Quick Installation Guide
Page 8
...the WLAN light on the Access Point is wireless 0. Click on the reset button for 15 seconds, and then let go. If you still encounter problems or have enabled any questions regarding the TEW-636APB, please contact TRENDnet's Technical Support Department. 6 Then open up your hardware settings again by...the Access Point, make sure to the access point configuration page from a wired computer. Click Wireless -> Virtual AP. Fourth, perform a factory reset. Copy the last six digits of the access point. Second, power cycle the Access Point. Wait 15 seconds, then plug the power back in...
...the WLAN light on the Access Point is wireless 0. Click on the reset button for 15 seconds, and then let go. If you still encounter problems or have enabled any questions regarding the TEW-636APB, please contact TRENDnet's Technical Support Department. 6 Then open up your hardware settings again by...the Access Point, make sure to the access point configuration page from a wired computer. Click Wireless -> Virtual AP. Fourth, perform a factory reset. Copy the last six digits of the access point. Second, power cycle the Access Point. Wait 15 seconds, then plug the power back in...