Optoma W401 Support and Manuals
Get Help and Manuals for this Optoma item
Most Recent Optoma W401 Questions
Optoma W401 Motherboard Is To Be Change As Hdmi Not Searching ....where It Could
(Posted by anshulsingh07 9 years ago)
Popular Optoma W401 Manual Pages
User's Manual - Page 1
... 56 OPTIONS | Filter Settings 57
Appendices 58 Troubleshooting 58
Image Problems 58 Other Problems 61 Remote Control Problems 61 LED Lighting Messages 62 On Screen Messages 63 Replacing the Lamp 65 Compatibility Modes 67 RS232 Commands and Protocol Function List 69 RS232 Pin Assignments 69 RS232 Protocol Function List 70 Ceiling Mount Installation 74 Optoma Global Offices 75...
User's Manual - Page 3
... or point the laser pointer on until the lamp module has been replaced. Do not look into the projector's lens when the lamp is on -screen display "OPTIONS | Lamp Settings" menu after replacing the lamp module. To reduce the risk of the lamp itself. When the lamp is in this user's guide. When replacing the lamp, please allow the unit to the end of...
User's Manual - Page 6
...
▀■ Avoid staring/facing directly into the projector beam at all times. Product Features
▀■ XGA (1024x768) / WXGA (1280x800) Native resolution ▀■ HD compatible - 720p and 1080p supported ▀■ BrilliantColorTM Technology ▀■ Security Bar and Kensington Lock ▀■ RS232 control ▀■ Rapid shutdown ▀■ Built...
User's Manual - Page 7
... ensure all parts listed below are in each Country, some regions may have different accessories.
2 × AAA Batteries
Documentation :
User's Manual Warranty Card Quick Start Card WEEE Card
(for EMEA only)
IR Remote Control (Remote may vary de- pending on model)
7 English If something is missing, please contact Optoma customer service.
Introduction...
User's Manual - Page 10
... (Connect to model's specifications.
9.
12V Trigger Relay (12V, 250mA)
™™ VGA dongle is 8. Composite Video Input Connector
YPbPr.
7. 3D Sync Out (5V)
™™ The interface is a 10. Power Socket
optional accesso- 11. VGA2-IN/YPbPr Connector
ry. RS-232 Connector (9-pin)
for Remote Mouse func- Audio1 Input for firmware upgrade)
3. RJ45
2. HDMI...
User's Manual - Page 14
... Devices
Once you have updated your console to the latest software ver- yy Go to the 3D channel. yy Launch the game. yy Once enabled, switch to the "Settings menu -> Display settings -> Video output -> HDMI". Installation
NOTE
™™ The 3D video source device must be necessary to use the projector's 3D Sync-Invert option...
User's Manual - Page 31
...User Off / CC1 / CC2 On / Off
On / Off
Yes / No
On / Off On / Off On / Off On / Off
Input Source Source Lock High Altitude Information Hide Keypad Lock Test Pattern 12V Trigger IR Function Background Color Advanced
Lamp Settings
Filter Settings...to the
signal type selected and the projector model you are using.
™™ (#1) "Color" and "Tint" are only supported in Video mode.
™™ ...
User's Manual - Page 48
Control Settings Refer to next page. User Controls
SETUP Network
LAN Settings
SETUP | Network
Control Settings
Exit
LAN Settings Refer to page 52.
English 48
User's Manual - Page 49
...projector from an external DHCP server automatically. `` Off: Assign an IP address manually.
IP Address Select an IP address. DNS Select DNS number. If you change the setting from one to another, when you exit the OSD menu, the new setting...Address Display an MAC address. User Controls
SETUP | Network | LAN Settings
Network Status
SETUP Network : LAN Settings
MAC Address
DHCP
IP Address
...
User's Manual - Page 52
... network function. Telnet Use this function to select the network function.
HTTP Use this function to select the network function. English 52 User Controls
SETUP | Network | Control Settings
SETUP Network : Control Settings
Creston
On
Extron
On
PJ Link
On
AMX Device Discovery
On
Telnet
On
HTTP
On
Apply
Exit
Creston Use this function to select...
User's Manual - Page 57
... Reset Reset the dust filter counter after 500 hours of use. Appendices
OPTIONS | Filter Settings
Filter Usage Hours
OPTIONS Filter Settings
Optional Filter Installed
Filter Reminder
Filter Reset
Yes 1000 hr
Exit
Filter Usage Hours Display the filter time. Filter Reminder Choose this function to display warning message after replacing or cleaning the dust filter.
57 English Select...
User's Manual - Page 58
... -screen `` Ensure all devices". Select the "Settings" tab. 3. Verify that the resolution setting of connectors are not crooked or broken. `` Check if the projection lamp has been securely installed. English 58 choose the resolution mode you experience a problem with your projector, please refer to the following steps. 5.
If the projector is lower than or equal to WUXGA...
User's Manual - Page 65
... or service center to prevent any loose parts from falling out of projector." Allow it is hot!
When the lamp life is recommended to cool down for at least 30 minutes before changing lamp! Warning: Lamp compartment is dropped.
65 English "Caution must be used to change the lamp as soon as possible.
Appendices
Replacing the Lamp
The projector automatically...
User's Manual - Page 66
...; (ii) Select "OPTIONS" (iii) Select
"Lamp Settings" (iv) Select "Lamp Reset" (v) Select "Yes". English 66 Unscrew the two screws on the projector.
™™ Do not touch the glass area of the lamp. Lift up the lamp handle and remove the lamp module slowly and carefully. 4 To replace the lamp module, reverse the previous steps. 8. Appendices...
User's Manual - Page 73
.../HDMI
dddd: FW version
e : Display mode 0/1/2/3/4/5/6/7/8
None/Presentation/Bright/Movie/sRGB/
User/Blackboard/DICOM SIM./3D
~XX151 1
7E 30 30 31 35 31 20 31 0D Model name
OKn
n : 1/2=X401/W401
~XX108 1
7E 30 30 31 30 38 20 31 0D Lamp Hours
OKbbbb
bbbb: LampHour
~XX108 2
7E 30 30 31 30 38 20...
Optoma W401 Reviews
We have not received any reviews for Optoma yet.