Oki LD610UPS Support and Manuals
Get Help and Manuals for this Oki Data item
View All Support Options Below
Free Oki LD610UPS manuals!
Problems with Oki LD610UPS?
Ask a Question
Free Oki LD610UPS manuals!
Problems with Oki LD610UPS?
Ask a Question
Popular Oki LD610UPS Manual Pages
Technical Reference - Page 3
... smells coming from the outlet, and contact the dealer, or Support Center. Warning
Ignoring the instructions marked by this symbol and erroneously operating the printer could result in death or serious injury.
A specific warning symbol is contained in or near the printer. What is specifically prohibited is contained in the pictograph (The symbol at left means...
Technical Reference - Page 9
... as follows:
Section 1: Introduction Section 2: Installation Section 3: Operation and Configuration Section 4: Troubleshooting Section 5: Cleaning and Maintenance Section 6: General Specifications Section 7: Interface Specifications Section 8: Appendix
It is an economical printer with numerous features making it suitable for your investment in this OKI printer product. Refer to search for...
Technical Reference - Page 11
During printer configuration setting, the ON LINE (POWER) indicator responses in the printer. LD610 User's Technical Reference
Page 1-3
1.3 PARTS IDENTIFICATION
Front view
1 2 3 4
Section ...the printer forward to open the Top cover of the printer. During printer configuration setting, the ERROR indicator responses in conjunction with the ERROR indicator to show the modes of the printer....
Technical Reference - Page 29
... described in this manual thoroughly. Some printer settings may disturb default settings on the front of the printer's buttons are used either singularly, or together, to these operations are based.
Most of the printer's settings are controlled via the POWER and FEED/LINE buttons with the ON LINE (POWER) indicator and ERROR indicator on which the instructional procedures in...
Technical Reference - Page 42
Write down its setting details or keep a copy of downloading, if ON LINE (POWER) and ERROR indicators respond differently from above mentioned procedure, an error may corrupt the firmware and prevent the printer from starting the printer in the "Wait to receive data" status (ERROR indicator: blinking red light) before you manually turn off the printer. • During the process of...
Technical Reference - Page 43
... Configuration
3.7 FONT DOWNLOAD MODE
In this mode, the printer is in the "Wait to receive data" status (ERROR indicator: blinking red light) before
you restart the printer. • When not receiving reboot command, manually reboot the printer and restart in Font Download Mode
Start-up
Activation via operation setting mode or download command. ON LINE (POWER) indicator...
Technical Reference - Page 46
... 1/2 bit READY/BUSY control (single item buffer), READY/BUSY control (multi buffer), Xon/Xoff, Protocol for driver(STATUS4), STATUS3
Page 3-18
LD610 User's Technical Reference
Section 3: Operation and Configuration
3.11 PRINTER CONFIGURATIONS SETTING
You can set the printer configuration by sending SBPL commands from the host computer or by using the Utilities Tool application provided...
Technical Reference - Page 47
... Download
Firmware download
31
Reboot mode *5
Setting contents
Protocol for driver(STATUS4)Cyclic response *3 Protocol for driver(STATUS4)ENQ response *3 1 port connection/ENQ response(STATUS3) Multi/ 1 item 010 to 200 (1=50ns) Standard code/Nonstandard code
Nonstandard code settings for IEEE1284+USB specification only. *5.
Section 3: Operation and Configuration
No. The printer will...
Technical Reference - Page 52
Damaged platen gear. Data input error.
Defective main circuit board. Ribbon stock and media are only applicable to the next section.
Set media and media guide correctly Set the sensor correctly by printer setting tool.
Troubleshoot interface - Ensure correct data stream. Replace platen roller. Use only OKI-certified media. Use only OKI-certified media. Section 4: ...
Technical Reference - Page 54
... be a hardware problem.
Systematically perform checks and tests to verify. UNIVERSAL SERIAL BUS (USB) INTERFACE
If nothing prints during a test print, verify the device drivers have been successively installed by connecting from the host computer. Reinstall as required. Reboot the PC and the printer. Ensure the serial cable (Null Modem) meets specifications and is turned...
Technical Reference - Page 55
... documentation for details.
Ensure the host's peripheral settings are set for Centronics output for instructions. CENTRONICS INTERFACE
CHK
TROUBLESHOOTING STEP
Ensure the interface module is connected to that procedure within this manual for faster throughput. Ensure the printer cable is correctly installed. If using a Windows printer driver, ensure the correct port is correctly...
Technical Reference - Page 76
... below, received data may be incorrect. 1) When the printer is Offline 2) When an error has occurred in the printer
Pin Assignments
1ĎHost with DB-25P terminal
Printer
CD
1
RD...problem, it is on. 2) Turning the printer on after the printer receives a request from the printer to the host Data terminal READY Signal ground Data set READY Send request READY to print the first print data...
Technical Reference - Page 82
... Settings
Installation of USB port should be established depending on the manufacturers or models. Notes • OS environment corresponding to the USB interface is necessary to install the USB driver in the printer driver installation specifications. As for the USB driver installation procedure, refer to [How to Install the USB Standard Print Support] in addition to the printer driver...
Technical Reference - Page 84
...; Send the print data by LPR and FTP of TCP/IP and dedicated socket protocol. (STATUS3, Protocol for
driver (STATUS4)) • Use socket connection to get the printer status. Section 7: Interface Specifications 7.5 LOCAL AREA NETWORK (LAN) ETHERNET (cont'd)
Communication configuration
Maximum receive buffer capacity
The following settings can be configured via the Printer configuration tool or...
Technical Reference - Page 86
...)] and enter user name and password to advance to the display below.
To change and refer internal setup and to Section 7.5.7 Setting/Displayed Items.
7.5.7 Setting/Displayed Items The following table shows the settings and referable sections as well as various variables. In MS-DOS command prompt, type in
No. Copyright 2011(C) OKI Data Americas, Inc. TCP/IP related...
Oki LD610UPS Reviews
We have not received any reviews for Oki yet.