Instruction Manual
Page 28
...Installation/connection Part list: A Faceplate 1) B Escutcheon 1) C Mounting sleeve 1) D Wiring harness 1) E Removal tool 2) F Flat head screw (for Nissan cars 4) G Round head screw (for Toyota cars 4) H Microphone (3 m) (KDC-X796 only)B 1) Basic procedure 1 Remove the key from the ignition switch, then ...disconnect the · terminal of the car battery. 2 Make proper input and output wire connections. \ (page 30) 3 Install the unit to your car...
...Installation/connection Part list: A Faceplate 1) B Escutcheon 1) C Mounting sleeve 1) D Wiring harness 1) E Removal tool 2) F Flat head screw (for Nissan cars 4) G Round head screw (for Toyota cars 4) H Microphone (3 m) (KDC-X796 only)B 1) Basic procedure 1 Remove the key from the ignition switch, then ...disconnect the · terminal of the car battery. 2 Make proper input and output wire connections. \ (page 30) 3 Install the unit to your car...
Instruction Manual
Page 29
... (10 m) is an obstacle between this unit during installation, consult your vehicle. Do not touch the metal part of your Kenwood dealer. ■■Reception may become hot. ■■Mounting and wiring this work to a too strong signal. ¤ CAUTION Install this unit in the console of this unit and the...
... (10 m) is an obstacle between this unit during installation, consult your vehicle. Do not touch the metal part of your Kenwood dealer. ■■Reception may become hot. ■■Mounting and wiring this work to a too strong signal. ¤ CAUTION Install this unit in the console of this unit and the...
Instruction Manual
Page 30
FM/AM antenna input (JASO) Antenna Cord Fuse (10A) Wiring harness D Rear output R L Front output Sub Woofer output Microphone H (KDC-X796 only) White White/Black Gray Gray/Black Green Green/Black Purple Purple/Black To front left speaker To front right speaker To ... control feature, you need to the antenna control terminal in the vehicle. (Max. 300mA, 12V) To connect the Kenwood navigation system, consult your car is stereo type and does not have any resistance. Wiring connection USB connector AUX input (Stereo) Use the mini-plug (3.5 mm; 1/8") cable which is required. (Not used...
FM/AM antenna input (JASO) Antenna Cord Fuse (10A) Wiring harness D Rear output R L Front output Sub Woofer output Microphone H (KDC-X796 only) White White/Black Gray Gray/Black Green Green/Black Purple Purple/Black To front left speaker To front right speaker To ... control feature, you need to the antenna control terminal in the vehicle. (Max. 300mA, 12V) To connect the Kenwood navigation system, consult your car is stereo type and does not have any resistance. Wiring connection USB connector AUX input (Stereo) Use the mini-plug (3.5 mm; 1/8") cable which is required. (Not used...
Instruction Manual
Page 31
... using the mounting sleeve (Japanese car) 1 Remove the mounting sleeve and escutcheon B from the unit. 2 Align the holes in place. T N NT T/N B 8 mm MAX. Other wiring connection has been completed earlier. (page 30) D 2 1 3 Dashboard of C your car 4 5 B Bend the appropriate tabs to the C unit. G ø5mm T: Toyota cars N: ... Installing the unit 1 3 2 1 B A 2 Before attaching, make sure the direction of the escutcheon is correct. (Wider hooks on the bottom side.) Connect the wiring harness to hold the mounting sleeve firmly in the unit (on the right.
... using the mounting sleeve (Japanese car) 1 Remove the mounting sleeve and escutcheon B from the unit. 2 Align the holes in place. T N NT T/N B 8 mm MAX. Other wiring connection has been completed earlier. (page 30) D 2 1 3 Dashboard of C your car 4 5 B Bend the appropriate tabs to the C unit. G ø5mm T: Toyota cars N: ... Installing the unit 1 3 2 1 B A 2 Before attaching, make sure the direction of the escutcheon is correct. (Wider hooks on the bottom side.) Connect the wiring harness to hold the mounting sleeve firmly in the unit (on the right.
Instruction Manual
Page 32
...positions using tape or the like. ■■Install the microphone as far away as possible from the H installation surface. 3 Install the microphone. 4 Wire the microphone cable up to the optimum level. / Check the cords and connections. "IN" flashes. "PROTECT" appears and no operations can be heard...the release coated paper of double-face adhesive tape to the radio. The tag memory of tape. Reset the unit. Installing the Microphone Unit (KDC-X796 only) 1 Check the installation position of the microphone H. 2 Remove oil and other dirt from the cell-phone. CD-R/CD-RW ...
...positions using tape or the like. ■■Install the microphone as far away as possible from the H installation surface. 3 Install the microphone. 4 Wire the microphone cable up to the optimum level. / Check the cords and connections. "IN" flashes. "PROTECT" appears and no operations can be heard...the release coated paper of double-face adhesive tape to the radio. The tag memory of tape. Reset the unit. Installing the Microphone Unit (KDC-X796 only) 1 Check the installation position of the microphone H. 2 Remove oil and other dirt from the cell-phone. CD-R/CD-RW ...