IBM 8658 - Eserver xSeries 230 Support and Manuals
Get Help and Manuals for this IBM item
Most Recent IBM 8658 Questions
Ibm E-server Xseries 230 (type 8658) Server Title : The Sever Not Run Displa
IT can boot when start but mo display. I ant to known Trouble but I have not the use manual plea...
IT can boot when start but mo display. I ant to known Trouble but I have not the use manual plea...
(Posted by sompongtip 12 years ago)
IBM 8658 Videos
IBM NetFinity 5100 8658
Duration: 4:11
Total Views: 23
Duration: 4:11
Total Views: 23
Popular IBM 8658 Manual Pages
User Guide - Page 8
... related system shutdown . . . . 144 DASD checkout 144 Host Built-In Self Test (BIST 144 Bus fault messages 145 Undetermined Problems 145
Parts listing (Type 8658 147
Keyboards 149 Power cords 150
Related service information . . . . . 151
Safety information 152 General safety 152 Electrical safety 152
vi : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY
User Guide - Page 29
...drivers are using the correct device drivers, supplied with the connector, cable, or hub. - For example, for the problem.
v Use another device in the Configuration/Setup Utility program. v If the hub does not support auto-negotiation, manually.... Ethernet troubleshooting chart
Ethernet controller problem Suggested Action
The server stops running when loading device drivers. How ...
User Guide - Page 31
... of the driver with the Link Support Layer (LSL). Explanation: An error occurred while the driver was trying to run the diagnostic programs.
If you have an Ethernet adapter installed, make sure...that you installed an IBM Netfinity 10/100 Fault Tolerant Adapter and make sure that were not available.
Action: Restart the server. Table 2. Novell NetWare or IntraNetWare ODI driver messages for...
User Guide - Page 34
... compatible with each problem.
24 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY
Table 4. PermaNet Server:
Explanation: The failover option requires an adapter that is for PCI device.
Explanation: The specified I /O address setting in the PROTOCOL.INI file to the secondary Ethernet controller. Grouping Mode is installed. Problem Occurs on...
User Guide - Page 35
...: Verify that additional IBM Netfinity 10/100 Fault Tolerant Adapters are present or replace the Ethernet adapter that...SunSoft Solaris driver has been reset due to respond. Action: Verify that additional IBM Netfinity 10/100...driver cannot find any more devices to do. If the problem persists, run the diagnostic programs.
Device failed checksum test!
Action: Modify your hardware settings...
User Guide - Page 41
.../Setup Utility is part of the basic input/output system (BIOS) that comes with server models that have set passwords.
See "Using the Configuration/Setup Utility program" for more detailed information. The ServerGuide CDs also contain a collection of application programs, which you can install after your server is up and running. When the message Press F1 for IBM Netfinity...
User Guide - Page 43
... to be the same as the keyboard speed. You must replace the system board. See"Using passwords" on the full Configuration/Setup Utility main menu. System Owner's Name
Select this choice to set or change the system time sent to the Advanced System Management Processor (service processor) when the server is in the master boot...
User Guide - Page 45
...contains all the system error and warning messages that the system generated during POST. - v Exit Setup If you have made any combination of the following methods: v If an administrator password is corrected. Power-on password
After you to view the interrupt-request setting (IRQ) used by the Configuration/Setup Utility (system service processor). v Save Settings Select this choice...
User Guide - Page 46
...
To set the password override switch:
1. Install the server cover (see "Installing the cover" on page 48.
3.
If you want the server to ask for a password when you begin" on the server, set an administrator password. The administrator password provides access to ON.
4. You must replace the system board.
36 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY...
User Guide - Page 90
... controller supports half-duplex (HDX) and full-duplex (FDX) modes at the appropriate rate. However, you install this
80 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY
That is standard Ethernet (10BASE-T), Fast Ethernet (100BASE-TX), half duplex (HDX), or full duplex (FDX). The device drivers are provided on the network and then sets...
User Guide - Page 91
... the instructions that comes with the adapter. Note that contain the redundant pair.The integrated controller is active, then the secondary Ethernet controller cannot be loaded for each redundant pair of messages to install the AMD PCNet Ethernet Family adapter
device driver. 3. This can replace the NIC adapter without any other network operation. The setup...
User Guide - Page 97
...provides installation instructions for all Netfinity Manager systems from a system that is not attached to the managing system network:
v Serial Connection Control
Use the Serial Connection Control service to use a Netfinity Manager system modem to start services at scheduled times and dates for Web, you can also install additional copies of Client Services for you Netfinity server model, see...
User Guide - Page 102
...
later) v Critical File Monitor v DMI Browser (requires DMI Service Layer) v ECC Memory Setup (requires ECC memory) v Event Scheduler v File Transfer v Power On Error Detect
92 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY
v Update Connector Manager (NT 4.0, TCP/IP, and Web Browser Required)
Click Update Connector Manager (NT 4.0, TCP/IP, and Web Browser...
User Guide - Page 106
... services: v Alert Manager v Software Inventory v System Information Tool
96 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY This default setting might not need to be added later.
11. Shut down and restart the system for Netfinity Manager to run correctly. Microsoft SQL is supported through ODBC as well. Click either Yes or No. you...
User Guide - Page 124
... the files from the OS2/SERVICES directory into the source directory. 3.
These services are included with IBM Network Transport Services/2), Netfinity Manager can be done from the appropriate Netfinity Manager directory.
114 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY First, a source directory must be installed on your system. Create a new...
IBM 8658 Reviews
We have not received any reviews for IBM yet.