IBM 8487 - eServer xSeries 206 Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 8487 Manual Pages
User Manual - Page 24
... server. 8.
Go to -FRU index," on page 19). 2. If an error is displayed, look up the first error (see "Diagnostic LEDs" on page 86.
14 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide Note: The system-error log is available on page 80). 9. b. If the error log does not indicate a damaged FRU, check the operating-system...
User Manual - Page 25
... a user password set, you must type the password and press Enter,
when prompted, before the operating system will be resolved the next time you turn on the server, the power on the IBM Enhanced Diagnostics CD. v One short beep indicates the successful completion of the installed options. If POST detects a problem (more information. A single problem might sound...
User Manual - Page 26
...problem is not installed). In this case, the server displays more than one of the server configuration.
Failed This test discovered an error. These programs are not intended to be performed by trained service personnel. Error codes that is an error code or other information about the error.
16 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide...
User Manual - Page 28
... that have definite symptoms (see "Diagnostic error codes" on page 83. Save the test log to a file on a diskette or to the hard disk if you want to refer to the information that the BIOS code is not installed.
18 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide Insert the IBM Enhanced Diagnostics diskette into the external USB...
User Manual - Page 29
... the cause of BIOS code for the server is available at http://www.ibm.com/pc/support/. Updating BIOS code
You can update the BIOS code for the server through one of an error. v Installing an update package for the Linux or Microsoft® Windows operating
system, if available.
DIMM 3 error LED
DIMM 2 error LED
DIMM 4 error LED
DIMM 1 error LED
Microprocessor fan error LED
System fan...
User Manual - Page 30
... and monitor. 12. Insert the POST/BIOS update (flash) diskette into the diskette drive. Review the safety information beginning at "Safety information" on page 107 and "Handling static-sensitive devices" on the server to restart the operating system.
20 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide Locate the boot block recovery jumper (JP1...
User Manual - Page 31
... the jumper. Select Save Settings and press Enter. then, replace the support bracket and replace the side cover (see the User's Guide. Turn on page 24.
2.
Erasing a lost or forgotten password (clearing CMOS memory)
This section applies to set a new user password. Complete the following steps to lost or forgotten passwords, see "Removing and installing the support bracket" on page 28...
User Manual - Page 41
.../CD-RW combo
For information on replacing a CD-ROM drive or diskette drive, see "Removing and installing the support bracket" on page 36. otherwise, replace the support bracket (see "Replacing the CD-ROM drive in bay 2" on page 35 and "Replacing the diskette drive in bay 7. Some simple-swap Serial ATA models come with an IDE CD-ROM...
User Manual - Page 45
... installing the support bracket" on page 28), replace the bezel (see "Removing the side cover" on page 50. Drive clip
6. If you are installing a new CD-ROM drive, read the instructions that the blue side of the clip is facing outward and the arrow on the drive, and whether a SCSI ID needs to be set. To install...
User Manual - Page 49
...instructions. In the typical configuration, the standard hard disk drives and backplane are connected to make sure that the hard disk drive is printed on page 50. Before you install...from the server. Installing options 39 SCSI...models come with the drive for each hot-swap hard disk drive is operating correctly. Unlock and remove the side cover (see "Removing and installing the support...
User Manual - Page 51
... memory. 14. Route the signal cable so that the other options to connect the new drive. 13. The connectors are attached to the drive tray (use these cables to install or remove, do so now. Otherwise, close the door hatch, close the drive-bay lock bar, replace the support bracket (see "Removing and installing the support...
User Manual - Page 56
... documentation for complete instructions for additional information about SCSI adapters. then, rotate the bracket to control the internal hard disk drives. Expansion-slot cover
Rear adapter- Install the SCSI adapter (see "Removing and installing the support bracket" on page 44).
46 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide
Connect required...
User Manual - Page 102
...controller. 2. ServeRAID controller.
92 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide Error code/symptom
FRU/action
1xxx (Microcode checksum error)
1. ServeRAID-5i controller. 4. Install download jumpers, flash latest level BIOS and firmware for controller. ServeRAID controller.
3200 (Code DRAM error)
1. then, remove jumpers.
2.
ServeRAID...
User Manual - Page 155
... connectors 70
CD-ROM drive activity LED 4 eject button 4 installing 31 problems 86
© Copyright IBM Corp. 2004, 2007
CD-ROM drive (continued) removing 35
chart, troubleshooting 18 checkout, general 13 checkout, procedure 14 components 25
system board 69 configuration
parallel port 54 updating 51 Configuration/Setup Utility 9 connector battery 69 microprocessor 69 connectors adapter 69...
User Manual - Page 158
... controller 3
W
Web site compatible options 23
weight 3
T
tape drive, installing 31 test log 18
viewing diagnostic 17, 18 trademarks 142 troubleshooting
chart 18
U
Ultra320 SCSI connector 55 undetermined problems 97 universal serial bus (USB)
cables 56 connectors 56 front connector assembly, removing 64
148 xSeries 206 Type 8482 and 8487: Hardware Maintenance Manual and Troubleshooting Guide
IBM 8487 Reviews
We have not received any reviews for IBM yet.