IBM 8645 - Eserver xSeries 220 Support and Manuals
Popular IBM 8645 Manual Pages
Hardware Maintenance Manual - Page 8
...translations) . . . 127
Send us your comments 156 Problem determination tips 157 Notices 157 Trademarks 158
vi Hardware Maintenance Manual: xSeries 220 Type 8645 Symptom-to-FRU index 105
Beep symptoms 105 No beep symptoms 108 Diagnostic error codes 108 Error symptoms 111 POST error codes 112 Processor board LEDs 117 ServeRAID 117 Undetermined problems 117
Parts listing Type 8645 -
Hardware Maintenance Manual - Page 14
...v System error logging (POST)
v Upgradeable basic input/output system (BIOS) and diagnostics
v Vital product data (VPD) on the system board. and the ease with an Ethernet controller on memory, system board, and hot-swap drive backplane
6 Hardware Maintenance Manual: xSeries 220 Type 8645 The controller provides full-duplex (FDX) capability, which problems can be diagnosed and repaired...
Hardware Maintenance Manual - Page 32
... the Configuration/Setup Utility, make sure that a PCI interrupt is enabled.
24 Hardware Maintenance Manual: xSeries 220 Type 8645 Action: that Ethernet is assigned to unload the AFT.NLM module before issuing the bind command. Load the driver for the AFT module.
If the problem persists, contact your network supplier. Explanation: An unknown error has occurred when...
Hardware Maintenance Manual - Page 38
.... If you have set an administrator password through the Configuration/Setup
Utility program only if the optional system management adapter is installed in the server. The choices on some menus might appear on the BIOS version in your server. You cannot edit the fields. Product Data
30 Hardware Maintenance Manual: xSeries 220 Type 8645 You can press...
Hardware Maintenance Manual - Page 39
... select keyboard operating characteristics, such as the machine type and model, the server serial number, and the revision level or issue date of password protection: -
You must replace the system board. v Date and Time Select this choice to set the system date and time. Power-on the Configuration/Setup Utility menu only if the optional system management...
Hardware Maintenance Manual - Page 41
... the three most recent error codes and
messages that are used by PCI devices. Note: This choice is installed in your password in automatic configuration of the Configuration/Setup Utility do not save the changes and return to the server through one of the following methods: v If an administrator password has been set a power-on the main...
Hardware Maintenance Manual - Page 42
...battery. Notes: 1. You can start the Configuration/Setup Utility program and set an administrator password. See "Removing the side cover" on password to all choices on password. 4. The administrator password provides access to be changed by the user.
34 Hardware Maintenance Manual: xSeries 220 Type 8645 v Change the position of the password-override switch (switch 8 on switch block 1 on...
Hardware Maintenance Manual - Page 43
... main menu. You can use the configuration method that are available.
Turn on password. When the Would you can set of the password features.
question appears, make your server has a RAID adapter installed, use to all choices on the Configuration/Setup Utility main menu.
Note: If your selection and press Enter. 4.
v All choices are available...
Hardware Maintenance Manual - Page 71
Install the adapter:
a.
Installing options 63 Set any jumpers or switches as described by its top edge or upper corners, and align it with your adapter for you to route cables before you opened the front adapter support bracket, rotate it is fully seated, release the front adapter support bracket by pushing inward on the system...
Hardware Maintenance Manual - Page 89
... options.
2.
Read "System reliability considerations" on the server. Follow the instructions that comes with the option to access the full Configuration/Setup Utility menu. If you have set an administrator password through the Configuration/Setup Utility
program only if the optional system management adapter is installed in the server. 2.
I /O Ports choice appears only on page 87...
Hardware Maintenance Manual - Page 97
... then sets the controller to the network, the Ethernet controller automatically detects the data-transfer rate (10 Mbps or 100 Mbps) on the rear of the server. Configuring the Ethernet controller
When you connect the server to operate at both speeds.
However, you must install a device driver to enable the operating system to support...
Hardware Maintenance Manual - Page 113
...have available when servicing the computer. ...error codes 108 Error symptoms 111
POST error codes 112 Processor board LEDs 117 ServeRAID 117 Undetermined problems 117
This index supports xSeries 220 servers. The POST BIOS displays POST error codes and messages on page 1. System Board
1. Notes:
1.
Once the configuration has reset to the default, it must be saved in Setup to the manual...
Hardware Maintenance Manual - Page 119
... that comes with the
1. Replace DIMM X LED on
System Error and CPU X LED on .)
2. Diskette Drive
5. Monitor 2. Error symptoms
General
FRU/Action
CD ...manual tray-release opening. Cable
4. The diskette is installed correctly (proper orientation)
2. Run Diskette Drive Diagnostics.
3. Some IBM monitors have one.) c. If you have their own self-tests. If diagnostics pass, the problem...
Hardware Maintenance Manual - Page 125
... Board
Symptom-to the Hardware Maintenance Manual for the particular RAID adapter in slot labeled DIMM 1)
4. System Board c. 1 Microprocessor d. 1 Terminator Card in Slot 2 e. 1 Memory Module (minimum of 1 DIMM in the system being serviced. Replace the VRM
ServeRAID
For ServeRAID error codes and procedures, refer to -FRU index 117 If the problem remains, suspect the following (one...
Hardware Maintenance Manual - Page 165
... same configuration options set -up between ″working and non-working , what changes were made prior to problem resolution. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be encountered, use - Do diagnostics fail? - Are the exact machine type and models 2. Subject to...
IBM 8645 Reviews
Do you have an experience with the IBM 8645 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for IBM yet.
Earn 750 points for your review!