HP SureStore 2600fx User's Guide
Page 5
About This Guide This user's guide includes: Chapter 1 set-up information for the HP SureStore Optical 2600fx optical disk drive Chapter 2 information about choosing and using optical disks Chapter 3 front panel control description, operating instructions, and troubleshooting information The Reference section includes: • optical disk library supplies • HP sales offices • safety and regulatory information • warranty information • service information Glossary of Terms Index v
About This Guide This user's guide includes: Chapter 1 set-up information for the HP SureStore Optical 2600fx optical disk drive Chapter 2 information about choosing and using optical disks Chapter 3 front panel control description, operating instructions, and troubleshooting information The Reference section includes: • optical disk library supplies • HP sales offices • safety and regulatory information • warranty information • service information Glossary of Terms Index v
HP SureStore 2600fx User's Guide
Page 12
Setting up the HP SureStore Optical 2600fx This chapter discusses the environment, hardware and procedures that are necessary to connect a 2600fx optical disk drive to the host computer: • preparing the environment • understanding the rear panel • setting up the optical disk drive address • choosing the operation mode • connecting the 2600fx drive to the host system • preparing the host computer for use with the 2600fx • troubleshooting 1-2
Setting up the HP SureStore Optical 2600fx This chapter discusses the environment, hardware and procedures that are necessary to connect a 2600fx optical disk drive to the host computer: • preparing the environment • understanding the rear panel • setting up the optical disk drive address • choosing the operation mode • connecting the 2600fx drive to the host system • preparing the host computer for use with the 2600fx • troubleshooting 1-2
HP SureStore 2600fx User's Guide
Page 18
... internal cable length of the optical disk drive and the other end into the AC line connector on the back of all peripherals on the power to the host computer for full data protection. Plug one end of the power cord into the power outlet. 5. Caution Perform a full system backup prior to connecting the optical disk drive to the host computer. 1-8 Switch on the SCSI bus. Remove inserted disks before disconnecting power...
... internal cable length of the optical disk drive and the other end into the AC line connector on the back of all peripherals on the power to the host computer for full data protection. Plug one end of the power cord into the power outlet. 5. Caution Perform a full system backup prior to connecting the optical disk drive to the host computer. 1-8 Switch on the SCSI bus. Remove inserted disks before disconnecting power...
Optical Drive and Library SCSI-2 Command Reference
Page 10
... Error Codes A-19 B. Field Replaceable Units (FRUs) HP Field Replaceable Units (FRUs C-2 D. Micro/Macro-Moves HP Surestore Optical Micro-Move IDs D-2 E. Autochanger Error Codes Chapter Overview B-2 Request Sense Error Codes B-3 Additional Sense Data Format for Error Recovery For all models, EXCEPT 40fx and 80ex B-8 Hardware Error Codes B-19 Autochanger Move Error Codes B-29 Jukebox Micro-Move Error Codes B-32 Diagnostic Tests B-40 C. Storage Slot 3-71 Element Type Code 3H - Contents Element Type Code 1H - Drive Error Codes Chapter Overview A-2 Drive Request Sense Command...
... Error Codes A-19 B. Field Replaceable Units (FRUs) HP Field Replaceable Units (FRUs C-2 D. Micro/Macro-Moves HP Surestore Optical Micro-Move IDs D-2 E. Autochanger Error Codes Chapter Overview B-2 Request Sense Error Codes B-3 Additional Sense Data Format for Error Recovery For all models, EXCEPT 40fx and 80ex B-8 Hardware Error Codes B-19 Autochanger Move Error Codes B-29 Jukebox Micro-Move Error Codes B-32 Diagnostic Tests B-40 C. Storage Slot 3-71 Element Type Code 3H - Contents Element Type Code 1H - Drive Error Codes Chapter Overview A-2 Drive Request Sense Command...
Optical Drive and Library SCSI-2 Command Reference
Page 15
... Check Errors 34H 2-120 Table 2-115. Tables Table 2-95. Parameter List Data for Write Errors 2-113 Table 2-105. Parameter Codes/Structure for Byte 8 of the Log Select Command 2-110 Table 2-99. Error Counter Page for Last N Error Events Page . . . . . 2-117 Table 2-111. Parameter Pointers/Structure for Read Errors 03H 2-114 Table 2-106. Error Event Log 2-118 Table 2-112. Parameter Codes/Structure for Verify Errors 05H 2-115 Table 2-108. Mode Select (Group 2) Command...
... Check Errors 34H 2-120 Table 2-115. Tables Table 2-95. Parameter List Data for Write Errors 2-113 Table 2-105. Parameter Codes/Structure for Byte 8 of the Log Select Command 2-110 Table 2-99. Error Counter Page for Last N Error Events Page . . . . . 2-117 Table 2-111. Parameter Pointers/Structure for Read Errors 03H 2-114 Table 2-106. Error Event Log 2-118 Table 2-112. Parameter Codes/Structure for Verify Errors 05H 2-115 Table 2-108. Mode Select (Group 2) Command...
Optical Drive and Library SCSI-2 Command Reference
Page 19
Timeout Settings E-2 xviii Micro-Move Error Codes B-32 Table B-11. HP Surestore Optical Micro-Move ID Table (For models 40fx, 80ex, 125ex and 220mx D-17 Table E-1. Jukebox FRUs (For all models, EXCEPT 40fx, 80ex, 125ex and 220mx D-2 Table D-2. Diagnostic Tests (EXCEPT for models 40fx, 80ex, 125ex, and 220mx B-40 Table B-13. Sequence Tests (For models 40fx, 80ex, 125ex, and 220mx...
Timeout Settings E-2 xviii Micro-Move Error Codes B-32 Table B-11. HP Surestore Optical Micro-Move ID Table (For models 40fx, 80ex, 125ex and 220mx D-17 Table E-1. Jukebox FRUs (For all models, EXCEPT 40fx, 80ex, 125ex and 220mx D-2 Table D-2. Diagnostic Tests (EXCEPT for models 40fx, 80ex, 125ex, and 220mx B-40 Table B-13. Sequence Tests (For models 40fx, 80ex, 125ex, and 220mx...
Optical Drive and Library SCSI-2 Command Reference
Page 48
SCSI-2 Drive Commands SCSI-2 Drive Command Set Request Sense Command (03H) Table 2-7 Sense Data Format Error Code 70H or 71H Sense Data Format Byte 7 6 5 4 3 2 1 0 0 Valid Error Code (70H or 71H) 1 Reserved (0) 2 Reserved (0) ILI Rsvd (0) Sense Key 3 Information (MSByte) 4 Information Byte 5 Information Byte 6 Information (LSByte) 7 Additional Sense Length (0EH) 8 Reserved (0) 9 Reserved (0) 10 Reserved (0) 11 Reserved (0) 12 Additional Sense Code 13 Additional Sense Code Qualifier 14 Reserved (0) 15 SKSV Sense...
SCSI-2 Drive Commands SCSI-2 Drive Command Set Request Sense Command (03H) Table 2-7 Sense Data Format Error Code 70H or 71H Sense Data Format Byte 7 6 5 4 3 2 1 0 0 Valid Error Code (70H or 71H) 1 Reserved (0) 2 Reserved (0) ILI Rsvd (0) Sense Key 3 Information (MSByte) 4 Information Byte 5 Information Byte 6 Information (LSByte) 7 Additional Sense Length (0EH) 8 Reserved (0) 9 Reserved (0) 10 Reserved (0) 11 Reserved (0) 12 Additional Sense Code 13 Additional Sense Code Qualifier 14 Reserved (0) 15 SKSV Sense...
Optical Drive and Library SCSI-2 Command Reference
Page 49
... Error Code of 71H indicates that the CHECK CONDITION status returned is set to 04/04-(Logical Unit Not Ready, Format in bytes, as determined by the command, when the ILI bit is the result of the data on page 2-14. 2-12 Chapter 2 A Valid bit of 0 indicates that returned CHECK CONDITION status. Sense Key Specific Information If the Sense Key is set to...
... Error Code of 71H indicates that the CHECK CONDITION status returned is set to 04/04-(Logical Unit Not Ready, Format in bytes, as determined by the command, when the ILI bit is the result of the data on page 2-14. 2-12 Chapter 2 A Valid bit of 0 indicates that returned CHECK CONDITION status. Sense Key Specific Information If the Sense Key is set to...
Optical Drive and Library SCSI-2 Command Reference
Page 128
... SCSI-2 Drive Command Set Write and Verify (Group 1) Command (2EH) DPO EBP Transfer Length PBA ErsCntl Rel Adr A Disable Page Out bit of 0 indicates an erase automatically performs before writing the data. An Erase By-Pass bit of 1 instructs the target not to store the data in the cache after it has been transferred to the optical disk. An EBP bit of 0 indicates that logical block addressing...
... SCSI-2 Drive Command Set Write and Verify (Group 1) Command (2EH) DPO EBP Transfer Length PBA ErsCntl Rel Adr A Disable Page Out bit of 0 indicates an erase automatically performs before writing the data. An Erase By-Pass bit of 1 instructs the target not to store the data in the cache after it has been transferred to the optical disk. An EBP bit of 0 indicates that logical block addressing...
Optical Drive and Library SCSI-2 Command Reference
Page 151
SCSI-2 Drive Command Set Log Sense Command (4DH) Table 2-105 Table 2-106 Error Counter Page for Read Errors 03H Byte 7 6 5 4 3 2 1 0 0 Rsvd (0) Page Code (03H) 1 Reserved (0) 2 Page Length (n-3) (MSByte) 3 Page Length (n-3) (LSByte) 4 Parameter Code (MSByte) (See Table 2-104 on page 2-113 or Table 2-106 on page 2-114) 5 Parameter Code (LSByte) 6 Reserved (0) 7 Parameter Length (n-7) 8 Parameter Value n Parameter Value Parameter Codes/Structure for all pages 2-114 Chapter...
SCSI-2 Drive Command Set Log Sense Command (4DH) Table 2-105 Table 2-106 Error Counter Page for Read Errors 03H Byte 7 6 5 4 3 2 1 0 0 Rsvd (0) Page Code (03H) 1 Reserved (0) 2 Page Length (n-3) (MSByte) 3 Page Length (n-3) (LSByte) 4 Parameter Code (MSByte) (See Table 2-104 on page 2-113 or Table 2-106 on page 2-114) 5 Parameter Code (LSByte) 6 Reserved (0) 7 Parameter Length (n-7) 8 Parameter Value n Parameter Value Parameter Codes/Structure for all pages 2-114 Chapter...
Optical Drive and Library SCSI-2 Command Reference
Page 175
... for this command is performed before writing the data. If a written block is used . The sense key/additional sense code will return a CHECK CONDITION status. A Physical Block Address bit of 1 suppresses the erase operation. The 9.1 and 5.2 Gbyte capacity drives cannot Format, Erase, Write, or Write and Verify 650 Mbyte and 1.3-Gbyte optical disks. For write-once optical disks, blank checking is issued with the Sense Key/Additional Sense Code set to BLANK CHECK/Overwrite...
... for this command is performed before writing the data. If a written block is used . The sense key/additional sense code will return a CHECK CONDITION status. A Physical Block Address bit of 1 suppresses the erase operation. The 9.1 and 5.2 Gbyte capacity drives cannot Format, Erase, Write, or Write and Verify 650 Mbyte and 1.3-Gbyte optical disks. For write-once optical disks, blank checking is issued with the Sense Key/Additional Sense Code set to BLANK CHECK/Overwrite...
Optical Drive and Library SCSI-2 Command Reference
Page 190
... media at the source element address with the destination element address. Write Buffer Command Writes data to perform predefined diagnostic test/exerciser routines. Jukebox SCSI-2 Commands Table 3-1 Jukebox SCSI-2 Command Set Numerical List of Commands Numerical List of the storage slots, mailslot, drives, and picker. 3-35 3-37 3-38 3-39 3-43 3-47 3-64 3-66 3-68 Chapter 3 3-3 Read Element Status Retrieves the status of Commands Code (hex.) Name Description Page Number 1DH 1EH 2BH 3BH 3CH...
... media at the source element address with the destination element address. Write Buffer Command Writes data to perform predefined diagnostic test/exerciser routines. Jukebox SCSI-2 Commands Table 3-1 Jukebox SCSI-2 Command Set Numerical List of Commands Numerical List of the storage slots, mailslot, drives, and picker. 3-35 3-37 3-38 3-39 3-43 3-47 3-64 3-66 3-68 Chapter 3 3-3 Read Element Status Retrieves the status of Commands Code (hex.) Name Description Page Number 1DH 1EH 2BH 3BH 3CH...
Optical Drive and Library SCSI-2 Command Reference
Page 240
... last hard error Total number of soft errors since last hard error Array of hard error Chapter 3 3-53 Jukebox SCSI-2 Commands Soft errors are recoverable with page code 31H. The Move Success Log is ONLY supported on page 3-53 Hard errors are recorded. NOTE Table 3-51 NOTE Table 3-52 Jukebox SCSI-2 Command Set Log Sense Command (4DH) Move Success Log Table Format This log is intended for use during normal jukebox operation, not diagnostic operation. Move Success Logs...
... last hard error Total number of soft errors since last hard error Array of hard error Chapter 3 3-53 Jukebox SCSI-2 Commands Soft errors are recoverable with page code 31H. The Move Success Log is ONLY supported on page 3-53 Hard errors are recorded. NOTE Table 3-51 NOTE Table 3-52 Jukebox SCSI-2 Command Set Log Sense Command (4DH) Move Success Log Table Format This log is intended for use during normal jukebox operation, not diagnostic operation. Move Success Logs...
Optical Drive and Library SCSI-2 Command Reference
Page 281
... the maximum sector number 70 A Parameter List was not prepared 71 A sector number of the Parameter List was greater than the maximum sector number 72 A sector count of the Parameter List is set to 0 in the W/R/S 73 Undefined condition is set in the DTS, DLS command 7D Setup command was issued while executing the Identify operation 7E A command was issued while executing another command 7F Undefined command...
... the maximum sector number 70 A Parameter List was not prepared 71 A sector number of the Parameter List was greater than the maximum sector number 72 A sector count of the Parameter List is set to 0 in the W/R/S 73 Undefined condition is set in the DTS, DLS command 7D Setup command was issued while executing the Identify operation 7E A command was issued while executing another command 7F Undefined command...
Optical Drive and Library SCSI-2 Command Reference
Page 302
Autochanger Error Codes Autochanger Error Codes Additional Sense Data Format for the most likely Field Replacable Unit to be the actual cause of the failure. Hardware Error Code Determined by fault isolation, this error code indicates the cause of a problem. First FRU The most likely Field Replacable Unit to be the cause of the failure. (See Table A-2 on page A-4) Second FRU The second most likely Field Replacable Unit...
Autochanger Error Codes Autochanger Error Codes Additional Sense Data Format for the most likely Field Replacable Unit to be the actual cause of the failure. Hardware Error Code Determined by fault isolation, this error code indicates the cause of a problem. First FRU The most likely Field Replacable Unit to be the cause of the failure. (See Table A-2 on page A-4) Second FRU The second most likely Field Replacable Unit...
Optical Drive and Library SCSI-2 Command Reference
Page 306
... elimination for the most likely cause of an error, but may not fix the associated problem. Autochanger Error Codes Hardware Error Codes Autochanger Error Codes NOTE Table B-7 Hardware Error Codes Hardware Errors are indicators for various FRUs runs automatically. Simply changing the FRU listed may or may not be the actual cause of RAM checksum error 05 RAM test error 06 SCSI chip error 07 Jukebox controller chip error 0F Configuration module failure Appendix B B-19
... elimination for the most likely cause of an error, but may not fix the associated problem. Autochanger Error Codes Hardware Error Codes Autochanger Error Codes NOTE Table B-7 Hardware Error Codes Hardware Errors are indicators for various FRUs runs automatically. Simply changing the FRU listed may or may not be the actual cause of RAM checksum error 05 RAM test error 06 SCSI chip error 07 Jukebox controller chip error 0F Configuration module failure Appendix B B-19
Optical Drive and Library SCSI-2 Command Reference
Page 310
... loopback data did not match what was sent (not supported) 2A Timed out waiting for RS-232 loopback data (not supported) 2B Timer A did not count down as expected (not supported) MOTOR CONTROL IC ERROR CODES 2C Failed read\write test to Motor control IC 2D Motor control IC loopback test failed 2E Motor control IC RAM test failed POWER SUPPLY ERROR CODES 33 Low voltage power supply failed 34 High voltage power supply failed DRIVE CONNECT ERROR CODES 38 Drive 1 not connected Appendix...
... loopback data did not match what was sent (not supported) 2A Timed out waiting for RS-232 loopback data (not supported) 2B Timer A did not count down as expected (not supported) MOTOR CONTROL IC ERROR CODES 2C Failed read\write test to Motor control IC 2D Motor control IC loopback test failed 2E Motor control IC RAM test failed POWER SUPPLY ERROR CODES 33 Low voltage power supply failed 34 High voltage power supply failed DRIVE CONNECT ERROR CODES 38 Drive 1 not connected Appendix...
Optical Drive and Library SCSI-2 Command Reference
Page 334
... slot to be empty. 17 Mailslot I /O Test Performs a combination of the speed factor as the first Utility parameter given. Returns an error code #57H Invalid Configuration if there are no cartridges loaded into the unit. Log 20 Set Speed Factor to Allows the mechanics to the mailslot with its original orientation. Quarter Speed Appendix B B-47 It moves a cartridge from the SCSI Interface. 19 Zero Maximum...
... slot to be empty. 17 Mailslot I /O Test Performs a combination of the speed factor as the first Utility parameter given. Returns an error code #57H Invalid Configuration if there are no cartridges loaded into the unit. Log 20 Set Speed Factor to Allows the mechanics to the mailslot with its original orientation. Quarter Speed Appendix B B-47 It moves a cartridge from the SCSI Interface. 19 Zero Maximum...
Optical Drive and Library SCSI-2 Command Reference
Page 338
... is run by SCSI command, set Byte 1 to be empty.) The autochanger requires a disk in Test 67. Autochanger Error Codes Autochanger Error Codes Jukebox Micro-Move Error Codes Table B-13 Sequence Tests (For models 40fx, 80ex, 125ex, and 220mx ONLY) No. Test Name 60 FRU Isolation Test 65 Calibrate Magazines 66 Clear Magazine Min/ Max 67 Calibrate Mailslot 68 Clear Mailslot Max/ Min 75 UPS...
... is run by SCSI command, set Byte 1 to be empty.) The autochanger requires a disk in Test 67. Autochanger Error Codes Autochanger Error Codes Jukebox Micro-Move Error Codes Table B-13 Sequence Tests (For models 40fx, 80ex, 125ex, and 220mx ONLY) No. Test Name 60 FRU Isolation Test 65 Calibrate Magazines 66 Clear Magazine Min/ Max 67 Calibrate Mailslot 68 Clear Mailslot Max/ Min 75 UPS...