HP 10LC - Optical Disk Jukebox Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
Popular HP 10LC Manual Pages
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 1
... do I check the health of my data cartridge? (LTO only 16 How do I check the health of the assessment test to Support 31 How do I run the System Performance Backup Pre-test 24 How do I turn on L&TT, please see the user guide.
For much data can I write to help you follow instructions from HP support.
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 2
Follow the Technical Support & Documentation link. Where is English only. Note The user guide is the L&TT user guide?
The user guide is available from the L&TT web page at http://www.hp.com/support/tapetools.
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 3
... be the backup server, but it could be another server if you are using a SAN.
• You will need the tape driver installed to run the performance tests. How do I install L&TT?
• L&TT is available for free download from http://www.hp.com/support/tapetools and on any server that came with your drive.
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 13
... Test. Warnings should be
overwritten. 5. Select the device and click Test on the toolbar. 3. Red stop signs indicate failures. The test will take 10-15 minutes. 6. Contact HP support and send the results in the ResultLog.ltt file. Open the Test Results tab to see the results of the test. 7. How do I run...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 15
... to ensure that the test is fine. Contact support in this indicates a faulty drive. The Drive Assessment test automates HP engineering expertise to accurately determine the health of your...is okay and a problem remains, examine other system components or the overall configuration to determine the location of the problem. The test evaluates whether or not a specific drive/tape combination will...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 16
..., there may be an issue with a trusted, good quality tape to Detailed Device information > Tape at address > (loaded
tape) > Cartridge Health in the support ticket and examine the margins. c. d.
Load the data cartridge into an LTO drive of the data written on tape measures the quality of known good health. 2.
If any of...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 17
... a drive of the test. Open the Test Results tab to see the results of known good health. 2. Install and run L&TT 3. Click Start Test. How do I check the health of my data cartridge? (Non-LTO)
1. Select the device and click Test on the toolbar. 4. In the Test Execution tab, select the drive...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 18
... be suspect. Go to Detailed Device information > Tape at address > (loaded tape) > Cartridge Health in the support ticket and examine the margins. If any of the data as viewed by the drives that ...of the data written on which the backup was performed.
2. After the backup, generate a support ticket for the drive on the tape. Repeat the backup using a different drive and tape combination. Was ...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 19
How many more uses are left with this cleaning cartridge? (LTO only)
1. Perform a clean as you normally would. 2. Go to Detailed Device information > Tape at address > Ejected
Tape > Cartridge Usage section of the support ticket to see the number of cleans performed and the estimated number of cleans remaining. After the clean is finished...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 24
or as shown - See System Performance Results tab for results Select the Backup Pre-test tab 4. Select the device and click Sys Perf on the toolbar. 3. and start 5. Set parameters as preferred - How do I run L&TT 2. Install and run the System Performance Backup Pre-test?
1.
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 25
How do I run the System Performance Restore Pre-test?
• Install and run L&TT • Select the device and click Sys Perf on the toolbar. • Select the Restore Pre-test tab • Set parameters as preferred - and start • See System Performance Results tab for results or as shown -
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 26
... to a tape is set to measure a specific tape/drive combination. Note - Install and run L&TT 2. The amount of the tape/drive combination.
This test will take a long time and overwrite any data on the toolbar. 4. Set parameters as the capacity marked on the cartridge which assumes 2:1 compression ratio and reasonably good error rate. and start. Insert...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 27
Fill out the pop-up on Send
• If not then 1. Click on your details 3. How do I send a support ticket by e-mail?
• If you have e-mail set up form with your server then 1. Use Save Support Ticket to compress them) and e-mail the archive file via another computer.
• Use the email address...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 29
This log records L&TT activity and is recorded. 4. Check Add I/O History to L&TT
Support (LTT_team@hp.com). You may be asked for troubleshooting L&TT issues. Recreate the issue so that begin with EventLog and mail them to Event Log. 3. The most recent file is EventLog.ltt; Archive all ...
HP StorageWorks Library and Tape Tools FAQ - Windows GUI Version - Page 31
The file can be viewed using L&TT. Archive and e-mail this file to see the results summary. How do I send the results of all L&TT tests are automatically saved to the ResultLog.ltt file in the /logs directory. Just double-click on it. Scroll to the end to Support.
The results of the assessment test to Support?
HP 10LC Reviews
We have not received any reviews for HP yet.