Owner's Manual
Page 7
... Top Plate Assembly Light Socket (2) Motor Assembly Cover Motor Drive Board Controller Board No. 10-24 x 3/8" Hex Head No. 8-32 x 1" Phillips Screw No. 8-32 x 3/8" Slotted Hex Head Screw Power Cord For Help, call 1-800-35-GENIE or visit www.geniecompany.com 7 Parts List Item 1 ... 2-Conductor Wire (main carton) 1 Roll 1 Roll Insulated Staple (red bag) approx. 30 approx. 30 Wall Console (main carton) 1 1 #6 x 1-1/4" Pan Head Screw (red bag) 2 2 Entrapment Warning Label (manual)(main carton) 1 1 Safe-T-Beam (STB) Sensor (Green LED)(main carton) 1 1 Safe-T-Beam (STB) Source (Red...
... Top Plate Assembly Light Socket (2) Motor Assembly Cover Motor Drive Board Controller Board No. 10-24 x 3/8" Hex Head No. 8-32 x 1" Phillips Screw No. 8-32 x 3/8" Slotted Hex Head Screw Power Cord For Help, call 1-800-35-GENIE or visit www.geniecompany.com 7 Parts List Item 1 ... 2-Conductor Wire (main carton) 1 Roll 1 Roll Insulated Staple (red bag) approx. 30 approx. 30 Wall Console (main carton) 1 1 #6 x 1-1/4" Pan Head Screw (red bag) 2 2 Entrapment Warning Label (manual)(main carton) 1 1 Safe-T-Beam (STB) Sensor (Green LED)(main carton) 1 1 Safe-T-Beam (STB) Source (Red...
Owner's Manual
Page 9
... Clamps, 4 (5/16"-18) Hex Shoulder Bolts, and 4 (5/16"-18) Hex Head Serrated Flange Nuts onto Bolts (Figure 11). Snap on Drive Screw next to align Drive Screw Hooks between First and Middle Rail Sections. • Latch two Hooks together and slide Collar over Hooks Collar 9 Rail Clamps 13 11D. Finger-tighten...Figure 11B) and (Figure 11C). • Snap Clip on Retaining Clip 10 Figure 11 Attach Middle Rail Section For Help, call 1-800-35-GENIE or visit www.geniecompany.com 9 C Install Coupler on collar 11B. Rail Strap 15 5/16"-18 Hex Head Shoulder Bolts 10 5/16"-18 Hex ...
... Clamps, 4 (5/16"-18) Hex Shoulder Bolts, and 4 (5/16"-18) Hex Head Serrated Flange Nuts onto Bolts (Figure 11). Snap on Drive Screw next to align Drive Screw Hooks between First and Middle Rail Sections. • Latch two Hooks together and slide Collar over Hooks Collar 9 Rail Clamps 13 11D. Finger-tighten...Figure 11B) and (Figure 11C). • Snap Clip on Retaining Clip 10 Figure 11 Attach Middle Rail Section For Help, call 1-800-35-GENIE or visit www.geniecompany.com 9 C Install Coupler on collar 11B. Rail Strap 15 5/16"-18 Hex Head Shoulder Bolts 10 5/16"-18 Hex ...
Owner's Manual
Page 25
Release Magnetic Carriage Assembly from Drive Screw. • Lubricate Drive Screw with Genie Lubricant (GLU-3) NOTE Use ONLY Genie Lubricant (GLU-3). Slight movement is subject to reverse on Emergency Release Knob. - WARNING If the door fails to the following two ...Sockets (Figure 41): • Rough service, 130 Volt bulbs are broken. If the door moves too much, contact a Genie Factory Authorized Dealer for service or call 1-800-35-GENIE or visit www.geniecompany.com 25 Other lubricants may cause undesired operation. D Installation is 3' - 4' above the ground, the...
Release Magnetic Carriage Assembly from Drive Screw. • Lubricate Drive Screw with Genie Lubricant (GLU-3) NOTE Use ONLY Genie Lubricant (GLU-3). Slight movement is subject to reverse on Emergency Release Knob. - WARNING If the door fails to the following two ...Sockets (Figure 41): • Rough service, 130 Volt bulbs are broken. If the door moves too much, contact a Genie Factory Authorized Dealer for service or call 1-800-35-GENIE or visit www.geniecompany.com 25 Other lubricants may cause undesired operation. D Installation is 3' - 4' above the ground, the...
Owner's Manual
Page 28
...for shorted Wires. • Check garage door for binding. • If a new installation, check Door Arm position. • Check operation of Rail Drive Screw are OK. • If not, check fuse or circuit breaker or non-compatible GFCI. Adjust as detailed in the Safe-T-Beam® System Self-... Opener. Adjust as detailed in Maintenance Section. • WARNING: If you suspect a problem with the garage door hardware or springs,contact a Genie Factory Authorized De aler for no power, have a licensed electrician check circuit and wiring. 2. Door starts up Door will not turn off •...
...for shorted Wires. • Check garage door for binding. • If a new installation, check Door Arm position. • Check operation of Rail Drive Screw are OK. • If not, check fuse or circuit breaker or non-compatible GFCI. Adjust as detailed in the Safe-T-Beam® System Self-... Opener. Adjust as detailed in Maintenance Section. • WARNING: If you suspect a problem with the garage door hardware or springs,contact a Genie Factory Authorized De aler for no power, have a licensed electrician check circuit and wiring. 2. Door starts up Door will not turn off •...