Instruction Manual
Page 5
... the wheel is in a well ventilated area, a nd work in motion or kickback may be placed under their own weight. Threaded Clamp Nut (D28402, D28402N) I. Lock-Off Lever J. Never attempt to filter out microscopic particles. • Avoid prolonged contact with both sides, near the line of cut...dust from chemically-treated lumber (CCA). Paddle Switch H. If wheel is restarted. • Support large panels to eliminate the cause of the grinder may occur. WARNING: Use of use, noise from face and body. Always use . Under some conditions and duration of this product may walk...
... the wheel is in a well ventilated area, a nd work in motion or kickback may be placed under their own weight. Threaded Clamp Nut (D28402, D28402N) I. Lock-Off Lever J. Never attempt to filter out microscopic particles. • Avoid prolonged contact with both sides, near the line of cut...dust from chemically-treated lumber (CCA). Paddle Switch H. If wheel is restarted. • Support large panels to eliminate the cause of the grinder may occur. WARNING: Use of use, noise from face and body. Always use . Under some conditions and duration of this product may walk...
Instruction Manual
Page 6
... to strip. NOTE: If the gear case and motor housing become separated by a DEWALT service center. Overtightening could cause screws to motor housing. 90˚ 90˚ ... reconnecting the tool, depress and release the trigger switch to use with grinder accessories. Accessories It is important to choose the correct guards, backing pads... ./lbs. See pages 6-7 for information on choosing the correct accessories. 5 English FIG. 1 C D28402 D28402N F D28110 D28112 S IA B J K (D28402) L L K G H K ASSEMBLY AND ADJUSTMENTS ATTACHING SIDE HANDLE The side handle (E) can be...
... to strip. NOTE: If the gear case and motor housing become separated by a DEWALT service center. Overtightening could cause screws to motor housing. 90˚ 90˚ ... reconnecting the tool, depress and release the trigger switch to use with grinder accessories. Accessories It is important to choose the correct guards, backing pads... ./lbs. See pages 6-7 for information on choosing the correct accessories. 5 English FIG. 1 C D28402 D28402N F D28110 D28112 S IA B J K (D28402) L L K G H K ASSEMBLY AND ADJUSTMENTS ATTACHING SIDE HANDLE The side handle (E) can be...
Instruction Manual
Page 9
...AND REMOVING GUARD (D28110) O N 1. Rotate guard (I) into desired working position. OPERATION Guards and Flanges It is reconnected. Allow the grinder to stop before turning the tool off A by adjusting clamp, do not switch the tool on tool nameplate. Lift the tool from the ...damage to a power source depress and release the paddle switch (A) once [D28402: without depress- Every unthreaded accessory must be above after any inter- If the paddle switch is depressed. PADDLE SWITCH (D28402, D28402N) CAUTION: Before connecting the tool to the guard or the mounting hub ...
...AND REMOVING GUARD (D28110) O N 1. Rotate guard (I) into desired working position. OPERATION Guards and Flanges It is reconnected. Allow the grinder to stop before turning the tool off A by adjusting clamp, do not switch the tool on tool nameplate. Lift the tool from the ...damage to a power source depress and release the paddle switch (A) once [D28402: without depress- Every unthreaded accessory must be above after any inter- If the paddle switch is depressed. PADDLE SWITCH (D28402, D28402N) CAUTION: Before connecting the tool to the guard or the mounting hub ...
Instruction Manual
Page 10
... off and unplug the tool before turning the tool on the spindle. ing in continuous mode, press the rear part of spindle. 1. LOCK-ON BUTTON (D28402) The lock-on when the power is released. This will continue to A B J run after any interruption in power supply to the tool, such as previously... is in the off . English SLIDER SWITCH (D28110, D28112) CAUTION: Before connecting the tool to a power supply, be sure the switch is retained to the grinder by an O-ring on may result in damage to the tool or the wheel.
... off and unplug the tool before turning the tool on the spindle. ing in continuous mode, press the rear part of spindle. 1. LOCK-ON BUTTON (D28402) The lock-on when the power is released. This will continue to A B J run after any interruption in power supply to the tool, such as previously... is in the off . English SLIDER SWITCH (D28110, D28112) CAUTION: Before connecting the tool to a power supply, be sure the switch is retained to the grinder by an O-ring on may result in damage to the tool or the wheel.
