Dewalt D28402N Support and Manuals
Get Help and Manuals for this Dewalt item
This item is in your list!
View All Support Options Below
Free Dewalt D28402N manuals!
Problems with Dewalt D28402N?
Ask a Question
Free Dewalt D28402N manuals!
Problems with Dewalt D28402N?
Ask a Question
Popular Dewalt D28402N Manual Pages
Instruction Manual - Page 2
...parts. An undersized cord will draw.
The following table shows the correct size to follow all instructions listed... whether the outlet is properly grounded. Replace damaged cords
immediately. If in the presence...install a polarized outlet. The smaller the gage number,
the heavier the cord.
Check with all instructions. Double insulation eliminates
the need for Cord Sets...
Instruction Manual - Page 3
... of this manual. If damaged, have the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on another tool.
Accessories that have the tool serviced before using. SERVICE
• Tool service must be performed only by hand or against your model. Use of unauthorized parts or failure to follow maintenance instructions may be suitable...
Instruction Manual - Page 4
... injury to fingers, hands, and arms. Use... may be above listed minimum wheel speed ...brush or flap disc causing an uncontrolled cut into area that may cause serious personal injury.
• Always use proper guard with a "live " and shock the operator.
• Do not use Type...brush has loose wires, they will make exposed metal parts... replacement wheel, or a new or replacement wire brush installed,...
Instruction Manual - Page 5
...Support large panels to hearing loss. COMPONENTS (Fig. 1)
A. Paddle Switch
H. Threaded Clamp Nut
(D28402, D28402N...respiratory or other construction activities. Guard
B. Spindle (not shown)...WARNING: Use of this type of the panel.
Lock-...hands on both sides, near the line of cut for the dust exposure. Lock On Button (D28402... movement of the grinder may promote absorption ...
Instruction Manual - Page 6
...switch to ensure that
the handle is important to choose the correct guards, backing pads and flanges to use with grinder accessories. NOTE: If the gear case and motor housing become separated by a DEWALT service... 1
C
D28402 D28402N
F
D28110
D28112
S
IA
B
J
K
(D28402)
L
L
K
G H
K
ASSEMBLY AND ADJUSTMENTS
ATTACHING SIDE HANDLE
The side handle (E) can be serviced and re-assembled...
Instruction Manual - Page 7
... unthreaded accessory must be rated for use with sanding flap discs (Type 27 and 29) and wire brushes. Mounting Guard
MOUNTING AND REMOVING GUARD (D28112, D28402, D28402N)
CAUTION: Turn off . Some DEWALT models are included in the accessory package.
6 Mounting instructions for these accessory guards are provided with a guard intended for at least the speed recommended on the tool warning...
Instruction Manual - Page 8
... the
slots (O) on the gear case. Do not operate the grinder with clamp lever in open , rotate
the guard (I
7 If, after a period of the gear case hub at the factory. 4-1/2" Cutting Wheels
Sanding Discs
4-1/2" Sanding Flap Discs
English
Type 1 guard backing flange
Type 1 guard backing flange
abrasive cutting wheel diamond cutting wheel
clamp nut
clamp nut...
Instruction Manual - Page 9
... a complete stop rotating before turning the tool off A by hand.
Turn the tool off . Push the guard down . PADDLE SWITCH (D28402, D28402N)
CAUTION: Before connecting the tool to use tool and take the tool and guard to a service center to rotate the guard by releasing the paddle switch.
MOUNTING AND REMOVING GUARD (D28110)
O N
1.
Make sure the wheel has come to...
Instruction Manual - Page 10
...Thread the wheel on may result in extended use a wrench to the grinder by pressing the rear part of the switch
and releasing.
This will continue to A
B
J
run after any ... Remove backing flange by hand.
3. CAUTION: Failure to properly seat the wheel before making any
adjustments or removing or installing attachments or accessories. Ensure the switch is in power supply...
Instruction Manual - Page 11
...service center.
1. Apply minimum pressure to the work surface, allowing the tool to operate at high speed.
3. ton, thread the clamp nut (H) on the raised sec-
Maintain a 20˚ to 30˚ angle..., Type 1 guard. If the wheel you
are installing is 1/8" (3.31mm) thick or less, place the threaded clamp nut on page 7 for more information. See
page 6 of this manual for...
Instruction Manual - Page 13
... brush must not touch guard when mounted
or while in a straight
5˚-15˚
line to prevent burning and swirling
of the wire wheel or brush to 10˚ angle between the edge of grinder ... or installing attachments or accessories. mately one inch of flanges. Mounting and Using Wire Brushes
and Wire Wheels
Wire cup brushes or wire wheels screw directly on the grinder
spindle without...
Instruction Manual - Page 14
... tool, turn the switch on and off as previously described to provide
maximum operator protection.
4. Push the guard down until the guard lug engages and rotates freely in injury resulting from the wheel.
4. Install the threaded clamp nut with a wrench.
5. Open the guard latch (M). To remove the guard, open the guard latch, rotate the guard so that the...
Instruction Manual - Page 15
... date of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com. Use a clean, dry cloth only.
For further detail of purchase. English
USING CUTTING WHEELS
WARNING: Do not use identical replacement parts. Changing the angle will repair, without charge, any accessory, please contact...
Instruction Manual - Page 16
... or see country specific warranty information contained either in Latin America. For products sold in the packaging, call 1-800-4-DEWALT for warranty information. no questions asked. LATIN AMERICA: This warranty does not apply to the warranty, DEWALT tools are covered by our: 1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal...
Instruction Manual - Page 52
Especificaciones
D28402, D28402N
Tensión de alimentación:
120 V AC/DC (
)
Consumo de corriente:
10 A
Frecuencia de ... Joppa Road, Baltimore, MD 21286 (MAR06) Form No. 641881-00 D28110, D28112, D28402, D28402N Copyright © 2005, 2006 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the kit box configuration; the array...
Dewalt D28402N Reviews
Do you have an experience with the Dewalt D28402N that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Dewalt yet.
Earn 750 points for your review!