Dewalt DW758 Support Question
Dewalt DW758 Support Question
Find answers below for this question about Dewalt DW758.Need a Dewalt DW758 manual? We have 2 online manuals for this item!
Question posted by flojo2 on February 21st, 2014
Dewalt Dw758 Grinder Wiring
I have a Dewalt DW758 grinder that the hot wire burnt up to the switch. Am replacing wiring need to know witch wires go where??
Current Answers
Related Dewalt DW758 Manual Pages
Instruction Manual - Page 3
...Page 4
English
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT:
1-800-4-DEWALT (1-800-433-9258)
Important Safety Instructions
WARNING: When using your unit is ...lit. Never connect the green (or green and yellow) wire to rain. An adapter, sketches B and C, is available for use tool for better and safer performance. No adapter is available for...
Instruction Manual - Page 4
... good condition. Use only 3-wire extension cords that have repaired by authorized service facility.
Check for Cord Sets
Volts
Total Length of checking to determine that purpose.
• Do not overtighten wheel clamp nut. Additional Safety Instructions for that it on switch. Replace or repair damaged cords. Have defective switches replaced by an authorized service...
Instruction Manual - Page 5
... Grinder 1/2"(13mm) Arbor, 3450 RPM DW758 - 8" Heavy Duty Bench Grinder 5/8"(16mm) Arbor, 3600 RPM
Installing Spark Guards and Eye Shield Brackets
TURN OFF TOOL ...switch. DW756,758/385498 8/20/01 7:43 AM Page 2
English
SAVE THESE INSTRUCTIONS
Motor
Be sure your power supply agrees with the nameplate marking. 120 Volts, 50/60 Hz means alternating current only should be used . All DeWalt tools...
Instruction Manual - Page 6
...side, marked "ON". To turn the tool on depress the side of the rocker switch, marked "OFF".
3 Tighten screws securely. EYE SHIELDS ARE NOT DESIGNED TO REPLACE SAFETY GLASSES. Turn on safety glasses. As... tool rest. Tighten the shields in place by removing the two screws. Before turning the grinder on, put on the grinder and allow it to the brackets, as shown in the bracket assembly. DW758)....
Instruction Manual - Page 7
...must fit within the confines of wire cup brushes may be rated higher than the RPM shown on production or heavy-duty jobs and tools exposed to remove and replace an accessory.
1. Users and ...5. DW756,758/385498 8/20/01 7:43 AM Page 4
English
Installing Tool Rests
TURN OFF AND UNPLUG THE BENCH GRINDER
Remove the tool rests from your distributor or local service center. Use clean, dry rag...
Instruction Manual - Page 10
... not apply to install buffing wheels and wire wheel brushes as well as before and tighten the nut firmly but do not overtighten.
Inspect the blotter for a full refund. Install the new wheel or other qualified service organizations, These service organizations service DeWalt tools always using DeWalt replacement parts.
Proof of thin cardboard or blotter...
Parts Diagram - Page 2
... 286068-00 761341-00 761344-00 761338-00 761340-00 761336-00
Parts List for DW758 Type 1
Description
Qty Required
ROTOR
1
STATOR
1
STATOR HOUSING
1
BASE
1
WASHER,...(R)
1
WASHER,CLAMP
4
NUT
1
NUT
1
GUARD COVER (L)
1
GUARD COVER (R)
1
SCREW
6
REST,TOOL
2
BRACKET,TOOL
2
SCREW
4
BUSHING,CORD
1
PLATE,CORD
1
CAPACITOR
1
CLIP,CAPACITOR
1
CORD/10'/18-3
1
www....
Parts Diagram - Page 3
... 5130830-00 286068-00 385531-00 761361-00 94593-03 143331-00 761370-00 5130830-00 286061-00
Parts List for DW758 Type 1
Description
Qty Required
WASHER,STAR
1
SCREW,GUARD
6
PLATE,SWITCH
1
SWITCH
1
SCREW
6
PLATE,BASE
1
RUBBER,FOOT
4
WASHER
4
SCREW
4
KNOB
2
BRACKET,R.
1
EYESHIELD
2
PLATE,FLAT
2
BOLT,CARRIAGE
2
RIVET
4
SCREW
4
BRACKET,L. MTG.
1
BRACKET,R. MTG...
Parts Diagram - Page 4
...-00 761358-00 429678-00 429691-00 761834-00 286049-00 286048-00 429600-00 429601-00
Parts List for DW758 Type 1
Description
Qty Required
WRENCH
1
CLIP,WRENCH
1
SCREW
1
SPACER
2
NUT,WIRE
3
WASHER
1
BUSHING
1
STAR WASHER
4
JAM NUT
2
BAG,HARDWARE
1
BAG,HARDWARE
1
BAG,HARDWARE
1
8IN WHEEL
1
8 IN. WHEEL A60
1
www.toolpartspro.com...
Similar Questions
Dwe43244n Problems
my grinder shuts off after 3 or 4 seconds. I can unplug and plug it back in but it does the same thi...
my grinder shuts off after 3 or 4 seconds. I can unplug and plug it back in but it does the same thi...
(Posted by rkba1911 5 months ago)
Power Cord Replacement
I have a dw758 grinder and need the power cord replaced. The old one was disconnected by someone els...
I have a dw758 grinder and need the power cord replaced. The old one was disconnected by someone els...
(Posted by marcusmiles1973 4 years ago)
Wiring Diagram For The Switch Wire Positions On A Dewalt Dw130v Drill
Red, blue, white and black wires. What positions do they connect in?
Red, blue, white and black wires. What positions do they connect in?
(Posted by Timdzeigler77 4 years ago)
9' Right Angle Grinder Dwe 4519
I am wondering if it is possible you can give me a torque value for this grinder? it is 120 V 15 A a...
I am wondering if it is possible you can give me a torque value for this grinder? it is 120 V 15 A a...
(Posted by angelcoleman 9 years ago)
