Dewalt DWE4519 Support and Manuals
Get Help and Manuals for this Dewalt item
This item is in your list!
View All Support Options Below
Free Dewalt DWE4519 manuals!
Problems with Dewalt DWE4519?
Ask a Question
Free Dewalt DWE4519 manuals!
Problems with Dewalt DWE4519?
Ask a Question
Most Recent Dewalt DWE4519 Questions
9' Right Angle Grinder Dwe 4519
I am wondering if it is possible you can give me a torque value for this grinder? it is 120 V 15 A a...
I am wondering if it is possible you can give me a torque value for this grinder? it is 120 V 15 A a...
(Posted by angelcoleman 9 years ago)
Popular Dewalt DWE4519 Manual Pages
Instruction Manual - Page 3
...(corded) power tool or battery-operated (cordless) power tool.
1) WORK...parts. Unmodified plugs and matching outlets will result in electric shock, fire and/or serious injury. Water entering a power tool will increase the risk of electric shock.
1 WARNING: To reduce the risk of injury, read the manual and pay attention to rain or wet conditions. Read all safety warnings and all instructions...
Instruction Manual - Page 5
... noise may contact hidden wiring or its own cord. Prolonged exposure to your power tool serviced by insulated gripping surfaces only, when performing an operation where the cutting accessory may cause hearing loss. i) Hold power tool by a qualified repair person using only identical replacement parts. b) Do not use face shield, safety goggles or safety glasses. c) The rated speed...
Instruction Manual - Page 6
...power tool's air vents.
Pinching or snagging causes rapid stalling of powdered metal may grab the surface and pull the power tool...toothed saw blade.
Wheels for maximum control over your power tool and the specific guard designed for Grinding and
Abrasive Cutting-Off Operations... that are recommended for your hand. The side handle should always be adequately guarded and are taken. For...
Instruction Manual - Page 8
... Cord Sets
Ampere ...support the workpiece to be caught in moving parts...tool and inspect the wheel for cracks or flaws.
• Always handle and store wheels in this tool for long periods of this tool may result. • Do not operate this manual is recommended for Grinders...power boosters that would cause the tool ...Air vents often cover moving parts.
• When not in...
Instruction Manual - Page 9
... hearing protection that are described in extended use . The symbols and their definitions are factory tested; DEWALT tools are as those dust masks that conforms to the State of this manual:
DWE4517
7" Angle Grinder double insulated 8,500 rpm
DWE4519
9" Angle Grinder double insulated 6,500 rpm
7 Wear protective clothing and wash exposed areas with the nameplate marking...
Instruction Manual - Page 10
... into contact with a soft mount, enabling easy wheel installation and removal.
WARNING: Accessories must be rotated 90° left or right of its original position. Side handle D. This grinder is controlled by a trigger switch (A).
Accessories and Attachments
It is designed for information on the tool warning label. See the chart on pages 11-13...
Instruction Manual - Page 11
... ADJUSTMENTS
WARNING: To reduce the risk of the two FIG. 3
C
side handle ports (H). Remove guard and flanges from power source before installing and removing accessories, before adjusting or when making repairs. NOTE: If the gear case and motor housing become separated
by a DEWALT service center. Overtightening could cause
screws to motor
housing.
3. An accidental start -up can...
Instruction Manual - Page 12
..., or
29 guard, be done by a DEWALT Service Center. DEWALT
WHEEL SURFACE
models DWE4517 and DWE4519 are included in the off position before turning the tool off , depress and release
A
trigger. The
GUARD
same guard is designed for use with
depressed center wheels (Type 27), and
hubbed grinding wheels (Type 27). Mounting instructions for these accessory
guards are
provided...
Instruction Manual - Page 16
...setting it down .
Wheel breakage and injury may result in the work
surface. Apply minimum pressure to work surface before turning the tool off. See the chart on pages 11-13 of this manual...gouges in damage to the tool or the wheel. Remove tool from work surface, to allow the tool to operate at extra cost from your local dealer or authorized service center.
1. Place wheel against...
Instruction Manual - Page 17
... must be removed for fast, rough material removal. Remove the tool from DEWALT service centers and DEWALT dealers. NOTE: Guard may be re-installed for optimal finish. O
2. To remove the wheel, reverse the above minimum accessory speed as shown on tool. Allow the tool to stop rotating before setting it down to operate
at extra cost from work surface...
Instruction Manual - Page 18
...of the wire brush or wheel to work surface before setting it .
Maintain contact between the tool
and work surface.
6. Remove the tool from wheel
breakage and wheel contact. 1. Mounting and ...a wrench on the hub of
the wheel and the work gloves when handling wire brushes or wheels. Install the guard as accessories and include proper flange. Securely tighten the two clamping...
Instruction Manual - Page 19
... to lengthen. J
17
Apply minimum pressure to work surface,
allowing the tool to stop rotating before setting it down until the guard lug engages and rotates
freely in the groove .... Tighten the guard skirt bolts securely before using the grinder. FIG. 16
2. Push the guard down . The guard body
should be positioned between the tool and the work surface.
5˚-10˚
4.
NOTE...
Instruction Manual - Page 20
... parts of all air vents with clean, dry air at high speed.
3. Cleaning
WARNING: Blow dirt and dust out of the tool. These chemicals may result. Undetectable damage to reach full speed before turning tool off and disconnect it from work surface, allowing tool to remove the wheel. Install the clamp nut, ensuring that the wheel remains centered...
Instruction Manual - Page 21
... not cover part failure due to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE DEWALT will repair, without charge, any defects due to products sold in Latin America, see website for warranty information. This warranty gives you specific legal rights and you need assistance in the packaging, call 1-800-4-DEWALT (1-800-4339258) for a free replacement. If...
Instruction Manual - Page 68
... handgrip; and the array of the tool. Accessories
7" Type 27 Grinding Wheel
...9" Sanding
Disc
7" Type 1 Diamond or Abrasive Wheel
DWE4519 6,500 RPM
REQUIRED GUARD
7" Type 27 Guard
9" Type...DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (JUL12) Part No. N190393 DWE4517, DWE4519 Copyright © 2012 DEWALT
The following are trademarks for one or more DEWALT power tools...
Dewalt DWE4519 Reviews
Do you have an experience with the Dewalt DWE4519 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Dewalt yet.
Earn 750 points for your review!