Dewalt D28065 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt D28065 manuals!
Problems with Dewalt D28065?
Ask a Question
Free Dewalt D28065 manuals!
Problems with Dewalt D28065?
Ask a Question
Most Recent Dewalt D28065 Questions
Dewalt D28065 Videos
máy mài góc dewalt d28065
Duration: 2:00
Total Views: 0
Duration: 2:00
Total Views: 0
DeWalt D28065 szlifierka 125 mm z chwytem dwur?cznym
Duration: 2:00
Total Views: 3,538
Duration: 2:00
Total Views: 3,538
DEWALT D28065 grinder unboxing
Duration: 6:43
Total Views: 1,280
Duration: 6:43
Total Views: 1,280
Popular Dewalt D28065 Manual Pages
Instruction Manual - Page 3
... Please read the instruction manual. NOTICE: Indicates a practice not related to follow the warnings and instructions may ignite the dust...1 Keep cord away from heat, oil, sharp edges or moving parts.
c) Keep children and bystanders away while operating a power tool.... QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). b) Do not ...
Instruction Manual - Page 4
... less likely to a rotating part of drugs, alcohol or medication. Check for operations different from those intended could result in a hazardous situation.
5) SERVICE a) Have your application. f)...qualified repair person using only identical replacement parts. This enables better control of the power tool in the hands of dust extraction and collection facilities, ensure these instructions to...
Instruction Manual - Page 5
...instructions, illustrations and specifications provided with arbor holes that do not match the mounting hardware of the power tool will normally break apart during this power tool.
Incorrectly sized accessories cannot be attached to function as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush...a grinder, sander, wire brush, ...instructions listed...
Instruction Manual - Page 7
...loading and susceptibility to spin freely. When the wheel, at you.
Proper wheel flanges support the wheel thus reducing the possibility of cut for larger power tool is binding or ... reach full speed and carefully reenter the cut " into existing walls or other blind areas. Supports must be used only for Sanding Operations
a) Do not use undamaged wheel flanges that can entangle...
Instruction Manual - Page 8
...manual is recommended for long periods of power and overheating. Minimum Gauge for Grinders
WARNING: The grinding wheel or accessory may be caught in doubt, use the next heavier gauge.
Additional Safety Rules for Cord Sets
Ampere Rating
Volts
Total Length of the wire wheel or brush...securely. If in moving parts and should always be ...support the workpiece to the brush.
Instruction Manual - Page 10
... Ring
G1. These heavy-duty angle grinders are professional power tools. Lock On Button
(D28065, D28115 only) C. An accidental startup can cause injury.
English
COMPONENTS (Fig. 1)
WARNING: Never modify the power tool or any part of it from power source before installing and removing accessories, before adjusting or when making repairs. Dust Ejection System™
(DES...
Instruction Manual - Page 13
... 27 and 29) and wire brushes. The tool may be serviced and re-assembled by more than Type 27 and 29 require different accessory guards not included with tool. Re-install guard and correct flanges for at least the speed recommended on pages 9-11 of this manual. Mounting instructions for these accessory guards are provided...
Instruction Manual - Page 14
...adjusting or when making repairs. Allow the grinder to stop before touching... tool and guard to a service center to the guard or ...conditions.
Undetectable damage to repair
or replace the guard.
Accessory ratings...operate the grinder with the grinder accessories. Lift the tool from power source before installing and removing...You should not be above listed minimum wheel speed as ...
Instruction Manual - Page 15
...Thread of accessory must be used with
included flanges. Backing flange is retained to the grinder by pulling and twisting flange away form the machine.
2. Depress the spindle lock button...The stamped steel quick-change backing flange (G1) for more information.
1. Install the stamped steel quick-change backing flange (G2) (D28065, D28065N
N
only) for Type 27 6" (152 mm) wheels or
the ...
Instruction Manual - Page 16
...730; angle between the tool and work
surface, allowing the tool to do not
change the angle of the backing flange.
3. Changing
the angle will ...twist while the tool is installed with the pilot on the raised section (pilot) of the...against the wheel.
4. Remove the tool from your local dealer or authorized service
center. 1. Allow the tool to the work surface.
Edge grinding wheels ...
Instruction Manual - Page 17
...approximately one inch of sanding disc and backing pad.
4. Allow
the tool to 15˚ angle between the tool and work
5˚-10˚
surface.
5. Place or appropriately thread backing pad...for grinding wheel, sanding flap disc, wire brush or wire wheel applications after sanding applications are snug.
5. Apply minimum pressure to 10˚ angle between the tool and work surface.
15 ...
Instruction Manual - Page 18
....
1.
Move the tool constantly in a straight line FIG. 13
to 10˚ angle between the edge of grinder may result in
the work surface.
2. A Type 27 guard is greatest when the ...
Maintain contact between the tool and work surface before setting it down . To remove the wheel, reverse the above procedure. CAUTION: Wheel or brush must not touch guard when mounted or while in ...
Instruction Manual - Page 20
... the angle will allow us to bend and may weaken the plastic materials used with your product now for use identical replacement parts. To minimize the risk of purchase.
• FOR YOUR SAFETY: Registering your local dealer or authorized service center.
Use a cloth dampened only with this . Apply minimum pressure to work surface before setting...
Instruction Manual - Page 21
...America, see country specific warranty information contained...DEWALT tools are covered by our:
1 YEAR FREE SERVICE DEWALT will repair,...repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-4339258) for any defects due to normal wear or tool abuse. Three Year Limited Warranty
DEWALT will maintain the tool and replace worn parts caused by others. FREE WARNING LABEL REPLACEMENT...
Instruction Manual - Page 72
... Co., 701 East Joppa Road, Baltimore, MD 21286 (OCT12) Part No. N234380 D28065, D28065N, D28115, D28115N Copyright © 2007, 2012 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and...
Dewalt D28065 Reviews
We have not received any reviews for Dewalt yet.