Installing the 1 x 2 SCSI Backplane
Page 8
... cable to the riser card or RAID controller. Depending on your kit contains more than one of the 4-pin connectors on the power cable to the 1 x 2 backplane. See Figure 1-4. See Figure 1-4. See Figure 1-4. If your system is not configured with a tape backup unit, use... power connector on the 1 x 2 backplane. If your system is already configured with a tape backup unit: a Connect the 14-pin connector on the power cable to the peripheral bay power connector on the 1 x 2 backplane. www.dell.com | support.dell.com F6590bk0.book Page 6 Tuesday, July 6, 2004 4:33 PM Figure 1-3....
... cable to the riser card or RAID controller. Depending on your kit contains more than one of the 4-pin connectors on the power cable to the 1 x 2 backplane. See Figure 1-4. See Figure 1-4. See Figure 1-4. If your system is not configured with a tape backup unit, use... power connector on the 1 x 2 backplane. If your system is already configured with a tape backup unit: a Connect the 14-pin connector on the power cable to the peripheral bay power connector on the 1 x 2 backplane. www.dell.com | support.dell.com F6590bk0.book Page 6 Tuesday, July 6, 2004 4:33 PM Figure 1-3....
Installing the 1 x 2 SCSI Backplane
Page 10
...attached peripherals. 7 Enter System Setup to ensure that may also need to verify the correct boot order. See the Dell Support website at support.dell.com for more information. 8 Update the system firmware. You may have a standalone system, reinstall the stabilizers and ...for the latest firmware updates. 9 Replace the bezel (if applicable). 1-8 Installing the 1 x 2 SCSI Module www.dell.com | support.dell.com F6590bk0.book Page 8 Tuesday, July 6, 2004 4:33 PM Completing the Installation 1 Check all cable connections that the RAID or SCSI controller card is configured correctly.
...attached peripherals. 7 Enter System Setup to ensure that may also need to verify the correct boot order. See the Dell Support website at support.dell.com for more information. 8 Update the system firmware. You may have a standalone system, reinstall the stabilizers and ...for the latest firmware updates. 9 Replace the bezel (if applicable). 1-8 Installing the 1 x 2 SCSI Module www.dell.com | support.dell.com F6590bk0.book Page 8 Tuesday, July 6, 2004 4:33 PM Completing the Installation 1 Check all cable connections that the RAID or SCSI controller card is configured correctly.
Installing the SCSI Backplane Daughter Card
Page 6
www.dell.com | support.dell.com Figure 1-1. See your system's User's Guide for more information. 13 Replace the bezel (if applicable). 1-4 Installing the SCSI Backplane Daughter Card Installing the SCSI Daughter Card SCSI backplane board SCSI daughter card standoffs (2) 8 To use an optional RAID controller card in a split 2 x 4 backplane configuration: a Connect SCSI ...drives 1, 2, and 3. This channel controls the boot drive (drive 0) and drives 1, 2, and 3. c Use a #2 Phillips screwdriver to tighten the captive screw that the RAID or SCSI controller card is configured correctly.
www.dell.com | support.dell.com Figure 1-1. See your system's User's Guide for more information. 13 Replace the bezel (if applicable). 1-4 Installing the SCSI Backplane Daughter Card Installing the SCSI Daughter Card SCSI backplane board SCSI daughter card standoffs (2) 8 To use an optional RAID controller card in a split 2 x 4 backplane configuration: a Connect SCSI ...drives 1, 2, and 3. This channel controls the boot drive (drive 0) and drives 1, 2, and 3. c Use a #2 Phillips screwdriver to tighten the captive screw that the RAID or SCSI controller card is configured correctly.
Installing the SCSI Backplane Daughter Card
Page 9
... controller card to activate the 2/4 split backplane configuration. NOTE: If a cable is configured correctly. See your system's User's Guide for more information. 13 Replace the bezel (if applicable). To use the optional RAID controller card in a split backplane configuration: a Connect SCSI channel A (channel 0) on... the controller card to ensure that the RAID or SCSI controller card is connected to the SCSIB backplane connector, ...
... controller card to activate the 2/4 split backplane configuration. NOTE: If a cable is configured correctly. See your system's User's Guide for more information. 13 Replace the bezel (if applicable). To use the optional RAID controller card in a split backplane configuration: a Connect SCSI channel A (channel 0) on... the controller card to ensure that the RAID or SCSI controller card is connected to the SCSIB backplane connector, ...
Activating the Integrated RAID Controller
Page 8
...controller has changed to step 18. www.dell.com | support.dell.com Figure 1-3. Installing the RAID Key hardware key latches (2) 17 If you have a PowerEdge 2800 system, go to reflect the presence of system operation before you have a PowerEdge 2850 system, replace the riser card. ...18 Close the system. 19 Reconnect the system to its electrical outlet and turn on the two plastic rivets to 4 hours of the RAID hardware. 21 Install and configure the RAID...
...controller has changed to step 18. www.dell.com | support.dell.com Figure 1-3. Installing the RAID Key hardware key latches (2) 17 If you have a PowerEdge 2800 system, go to reflect the presence of system operation before you have a PowerEdge 2850 system, replace the riser card. ...18 Close the system. 19 Reconnect the system to its electrical outlet and turn on the two plastic rivets to 4 hours of the RAID hardware. 21 Install and configure the RAID...