Information Update
Page 6
...not affected. Systems that have certain flat-panel displays attached. After installing the Windows Server 2003 operating system, enter the System Setup program, and enable console redirection, if desired. Hot-add will not be supported. To correct the problem, restart the system, enter... attached, or systems that console redirection is disabled by default). Under certain conditions, the image on systems that mode. Dell™ PowerEdge™ Expandable RAID Controller (PERC) cards and the Broadcom 5721 PCI-e NIC do not support hot-plug PCI-e operation. 4 Information Update www...
...not affected. Systems that have certain flat-panel displays attached. After installing the Windows Server 2003 operating system, enter the System Setup program, and enable console redirection, if desired. Hot-add will not be supported. To correct the problem, restart the system, enter... attached, or systems that console redirection is disabled by default). Under certain conditions, the image on systems that mode. Dell™ PowerEdge™ Expandable RAID Controller (PERC) cards and the Broadcom 5721 PCI-e NIC do not support hot-plug PCI-e operation. 4 Information Update www...
Installing the 1 x 2 SCSI Backplane
Page 10
...dell.com F6590bk0.book Page 8 Tuesday, July 6, 2004 4:33 PM Completing the Installation 1 Check all cable connections that may also need to verify the correct boot order. You may have been loosened during the procedure. 2 Arrange the cables so that they do not catch on , including any attached peripherals. 7 Enter System Setup...the back of the system until the tray is configured correctly. c Use a #2 Phillips screwdriver to tighten the captive screw that the RAID or SCSI controller card is in the upright position (if applicable). 6 Reconnect the system to the chassis. 4 Close the system....
...dell.com F6590bk0.book Page 8 Tuesday, July 6, 2004 4:33 PM Completing the Installation 1 Check all cable connections that may also need to verify the correct boot order. You may have been loosened during the procedure. 2 Arrange the cables so that they do not catch on , including any attached peripherals. 7 Enter System Setup...the back of the system until the tray is configured correctly. c Use a #2 Phillips screwdriver to tighten the captive screw that the RAID or SCSI controller card is in the upright position (if applicable). 6 Reconnect the system to the chassis. 4 Close the system....
Installing the SCSI Backplane Daughter Card
Page 6
...Connect SCSI channel B on the riser card to connector SCSIB on the riser card to ensure that the RAID or SCSI controller card is in a split 2 x 4 backplane configuration: a Connect channel A on... Backplane Daughter Card To use the optional integrated ROMB controller in the operating position. www.dell.com | support.dell.com Figure 1-1. b Connect SCSI channel B (channel 1) on the controller card to... electrical outlet and turn the system on, including any attached peripherals. 12 Enter System Setup to SCSIA on the SCSI backplane. This channel controls the boot drive (drive 0)...
...Connect SCSI channel B on the riser card to connector SCSIB on the riser card to ensure that the RAID or SCSI controller card is in a split 2 x 4 backplane configuration: a Connect channel A on... Backplane Daughter Card To use the optional integrated ROMB controller in the operating position. www.dell.com | support.dell.com Figure 1-1. b Connect SCSI channel B (channel 1) on the controller card to... electrical outlet and turn the system on, including any attached peripherals. 12 Enter System Setup to SCSIA on the SCSI backplane. This channel controls the boot drive (drive 0)...
Installing the SCSI Backplane Daughter Card
Page 9
...an error message. 10 Rotate the drive bay retraction bar toward the back of the system. 11 Close the system. 12 Enter System Setup to activate the 2/4 split backplane configuration. See your system's User's Guide for more information. 13 Replace the bezel (if applicable). ...Backplane Daughter Card 1-7 b Connect SCSI channel B (channel 1) on the controller card to connector SCSIA on the SCSI backplane. To use the optional RAID controller card in a split backplane configuration: a Connect SCSI channel A (channel 0) on the controller card to connector SCSIB on the SCSI backplane. This...
...an error message. 10 Rotate the drive bay retraction bar toward the back of the system. 11 Close the system. 12 Enter System Setup to activate the 2/4 split backplane configuration. See your system's User's Guide for more information. 13 Replace the bezel (if applicable). ...Backplane Daughter Card 1-7 b Connect SCSI channel B (channel 1) on the controller card to connector SCSIA on the SCSI backplane. To use the optional RAID controller card in a split backplane configuration: a Connect SCSI channel A (channel 0) on the controller card to connector SCSIB on the SCSI backplane. This...
Activating the Integrated RAID Controller
Page 8
... for the SCSI controller has changed to secure the insulator. If you have a PowerEdge 2800 system, go to 4 hours of the RAID hardware. 21 Install and configure the RAID software. If you have a PowerEdge 2850 system, replace the riser card. 18 Close the system. 19 Reconnect the system ... www.dell.com | support.dell.com Figure 1-3. Installing the RAID Key hardware key latches (2) 17 If you have a PowerEdge 1850 system, place the plastic riser card insulator over the riser card and press down on the system, including any attached peripherals. 20 Enter the System Setup program and ...
... for the SCSI controller has changed to secure the insulator. If you have a PowerEdge 2800 system, go to 4 hours of the RAID hardware. 21 Install and configure the RAID software. If you have a PowerEdge 2850 system, replace the riser card. 18 Close the system. 19 Reconnect the system ... www.dell.com | support.dell.com Figure 1-3. Installing the RAID Key hardware key latches (2) 17 If you have a PowerEdge 1850 system, place the plastic riser card insulator over the riser card and press down on the system, including any attached peripherals. 20 Enter the System Setup program and ...