Processor Upgrade Installation Guide (.pdf)
Page 3
...reflect the presence of the card. disclaims any manner whatsoever without notice. © 2004 Dell Inc. You should see options for virtual disk for the RAC displays. When the system boots, the Remote Access Control Detected message displays and the option ROM and firmware information for... Press to change without the written permission of Dell Inc. is subject to enter the configuration screen for the Boot Sequence has changed to either the entities claiming the marks and names or their products. Dell Inc. www.dell.com | support.dell.com Figure 2. Installing a RAC Card RAC card...
...reflect the presence of the card. disclaims any manner whatsoever without notice. © 2004 Dell Inc. You should see options for virtual disk for the RAC displays. When the system boots, the Remote Access Control Detected message displays and the option ROM and firmware information for... Press to change without the written permission of Dell Inc. is subject to enter the configuration screen for the Boot Sequence has changed to either the entities claiming the marks and names or their products. Dell Inc. www.dell.com | support.dell.com Figure 2. Installing a RAC Card RAC card...
Installing the 1 x 2 SCSI Backplane
Page 8
... 8 cable routing slot 2 1 x 2 module top filler plate peripheral drive bay Connecting the SCSI and Backplane Power Cables NOTE: The 1 x 2 drive 0 functions as the boot drive. b Connect one SCSI cable, use the existing power cable and complete step b and step c. 1-6 Installing the 1 x 2 SCSI Module If your system is already configured...the cable length may vary. 1 Connect the power cable harness connectors to the power connector on the power cable to the 1 x 2 backplane. www.dell.com | support.dell.com F6590bk0.book Page 6 Tuesday, July 6, 2004 4:33 PM Figure 1-3. See Figure 1-4.
... 8 cable routing slot 2 1 x 2 module top filler plate peripheral drive bay Connecting the SCSI and Backplane Power Cables NOTE: The 1 x 2 drive 0 functions as the boot drive. b Connect one SCSI cable, use the existing power cable and complete step b and step c. 1-6 Installing the 1 x 2 SCSI Module If your system is already configured...the cable length may vary. 1 Connect the power cable harness connectors to the power connector on the power cable to the 1 x 2 backplane. www.dell.com | support.dell.com F6590bk0.book Page 6 Tuesday, July 6, 2004 4:33 PM Figure 1-3. See Figure 1-4.
Installing the 1 x 2 SCSI Backplane
Page 10
... User's Guide for the latest firmware updates. 9 Replace the bezel (if applicable). 1-8 Installing the 1 x 2 SCSI Module See the Dell Support website at support.dell.com for more information. 8 Update the system firmware. b Rotate the drive tray release lever toward the back of the system until the ... the operating position. a Grasp both sides of the front panel and slide the drive tray towards the back of the system. www.dell.com | support.dell.com F6590bk0.book Page 8 Tuesday, July 6, 2004 4:33 PM Completing the Installation 1 Check all cable connections that may also need ...
... User's Guide for the latest firmware updates. 9 Replace the bezel (if applicable). 1-8 Installing the 1 x 2 SCSI Module See the Dell Support website at support.dell.com for more information. 8 Update the system firmware. b Rotate the drive tray release lever toward the back of the system until the ... the operating position. a Grasp both sides of the front panel and slide the drive tray towards the back of the system. www.dell.com | support.dell.com F6590bk0.book Page 8 Tuesday, July 6, 2004 4:33 PM Completing the Installation 1 Check all cable connections that may also need ...
Installing the SCSI Backplane Daughter Card
Page 6
... to tighten the captive screw that the RAID or SCSI controller card is in the operating position. This channel controls the boot drive (drive 0) and drives 1, 2, and 3. www.dell.com | support.dell.com Figure 1-1. This channel controls drives 4, 5, 8, and 9. See your system's User's Guide for more information. 13 Replace the bezel (if applicable...
... to tighten the captive screw that the RAID or SCSI controller card is in the operating position. This channel controls the boot drive (drive 0) and drives 1, 2, and 3. www.dell.com | support.dell.com Figure 1-1. This channel controls drives 4, 5, 8, and 9. See your system's User's Guide for more information. 13 Replace the bezel (if applicable...
Installing the SCSI Backplane Daughter Card
Page 8
... the retention peg facing the retention lever. See Figure 1-2. 9 To use the optional integrated ROMB controller in the open position. www.dell.com | support.dell.com 6 The daughter card fits between the sides of the system. See Figure 1-2. Figure 1-3. b Connect SCSI channel B on the... SCSI backplane. See Figure 1-2. 7 Rotate the drive bay retraction bar toward the front of the card guide. This channel controls the boot drive (drive...
... the retention peg facing the retention lever. See Figure 1-2. 9 To use the optional integrated ROMB controller in the open position. www.dell.com | support.dell.com 6 The daughter card fits between the sides of the system. See Figure 1-2. Figure 1-3. b Connect SCSI channel B on the... SCSI backplane. See Figure 1-2. 7 Rotate the drive bay retraction bar toward the front of the card guide. This channel controls the boot drive (drive...
Installing the SCSI Backplane Daughter Card
Page 9
This channel controls the boot drive (drive 0) and drive 1. Otherwise, the system will display an error message. 10 Rotate the drive bay retraction bar toward the back of the system. ...
This channel controls the boot drive (drive 0) and drive 1. Otherwise, the system will display an error message. 10 Rotate the drive bay retraction bar toward the back of the system. ...