Dell PowerEdge R300 Support and Manuals
Get Help and Manuals for this Dell item
View All Support Options Below
Free Dell PowerEdge R300 manuals!
Problems with Dell PowerEdge R300?
Ask a Question
Free Dell PowerEdge R300 manuals!
Problems with Dell PowerEdge R300?
Ask a Question
Most Recent Dell PowerEdge R300 Questions
The Dell Poweredge R300 Weight
I have asked to calculate the weight of our cabinet. We do have 4 Dell powerEdege R300 Servers.Can y...
I have asked to calculate the weight of our cabinet. We do have 4 Dell powerEdege R300 Servers.Can y...
(Posted by pauloum 8 years ago)
How Do I Enter The Raid Configuration Utility On Dell Poweredge R300
(Posted by thchuckc 9 years ago)
Dell PowerEdge R300 Videos
Dell PowerEdge R300
Duration: :58
Total Views: 3,480
Duration: :58
Total Views: 3,480
Popular Dell PowerEdge R300 Manual Pages
Rack Installation Guide - Page 8
... and stable before attempting to install the next system. General Installation Instructions
This installation guide provides instructions for trained service technicians installing one or more systems in a rack, complete all the system manufacturer's rack cabinets without tools, and the VersaRails™ rack kit can pinch your Product Information Guide for instructions on page 18.
6
Four...
Hardware Owner's Manual (PDF) - Page 35
... Configuration Wait until the process is being processed.
NVRAM_CLR NVRAM_CLR jumper is Remove NVRAM_CLR
jumper is
present, DIMMs must be installed in the System Setup program, or loose diskette/tape drive interface cable, or loose power cable.
If more memory is disabled: than one DIMM is installed installed.
BIOS Update Attempt Remote BIOS update
Failed! See "Troubleshooting...
Hardware Owner's Manual (PDF) - Page 38
... sector on hard drive. Diskette Drive" on page 147. faulty or improperly installed
the problem persists, see
subsystem, or no operating system on hard drive
Incorrect configuration settings in the System Setup program. System Messages (continued)
Message
Causes
Corrective Actions
No boot device available
Faulty or missing optical Use a bootable USB key, CD,
drive subsystem, hard or...
Hardware Owner's Manual (PDF) - Page 43
... by typing y (yes) or n (no). NOTE: Warning messages are installed in this table, see the system documentation on page 46. Embedded RAID
See "Using the System Setup
firmware responds with an Program" on support.dell.com
Invalid memory configuration.
For more information on valid memory configurations, please see the "Glossary" on page 102. Warning Messages
A warning...
Hardware Owner's Manual (PDF) - Page 56
... to Setup
System and Setup Password Features
NOTICE: The password features provide a basic level of protection, such as data encryption programs.
NOTICE: Anyone can disable the password by changing a jumper setting. This procedure is described in the System Setup program until a trained service technician changes the password jumper setting to Off, the system remains off after power is...
Hardware Owner's Manual (PDF) - Page 57
... Status is Disabled, and you assign a system password, enter the System Setup program and check the System Password option.
However, certain key combinations are not valid. To erase a character when entering your password. Using the System Password
After a system password is not case-sensitive. When the System Password option is set to completing step 5.
4 Press .
Assigning a System...
Hardware Owner's Manual (PDF) - Page 58
... shut down . If an incorrect system password is set to enter the correct password.
After you turn on page 59), the system accepts your password. NOTE: Password protection does not take effect until the correct password is set to take effect or continue working and reboot your system.
Exit the System Setup program and begin using your system.
6 Either...
Hardware Owner's Manual (PDF) - Page 60
...Enabled. A change an existing system password).
After you verify the password, the Setup Password setting changes to the Setup Password option becomes effective immediately (restarting the system is not locked through the Password Status option, you can use the Password Status option in conjunction with the Setup Password option to assign a new setup password, perform the steps in three...
Hardware Owner's Manual (PDF) - Page 66
... SAS/SATA backplane board. The processor and memory are installed directly on page 155.
66
Installing System Components Power is shown connecting over the control panel cabling. This cable should be required to the SATA controller on page 79. The optical drive connects to change a jumper setting. For more information, see "Optical Drive" on the system board. For more...
Hardware Owner's Manual (PDF) - Page 90
... and use the internal USB connector, the Internal USB Port option must configure the USB memory key with a boot image and then specify the USB memory key in the boot sequence in the Integrated Devices screen of the cable into a power distribution unit (PDU) or power outlet. See Figure 1-4.
See "System Setup Options" on the front control board for more information...
Hardware Owner's Manual (PDF) - Page 102
... Dell. NOTE: Reinstall the hard drives in six ranks (1, 2, 3, 4, 5, and 6) on two channels (A and B). System Memory
The six memory module sockets are located to the right side of the system board and can upgrade the system memory by installing combinations of the memory module sockets. NOTE: The memory modules must be PC-4200/5300 compliant. See your Product Information Guide...
Hardware Owner's Manual (PDF) - Page 130
... 24 hours.
130
Troubleshooting Your System See "Entering the System Setup Program" on the network are authorized to the same data transmission speed. Action
CAUTION: Only trained service technicians are all set to remove the system cover and access any procedure, see your Product Information Guide for complete information about safety precautions, working inside the system...
Hardware Owner's Manual (PDF) - Page 137
... peripherals, and disconnect the system from a USB memory key. See "Entering the System Setup Program" on page 104. 15 Close the system. If the problem persists, see "Getting Help" on page 68. 14 If a diagnostic test or error message indicates a specific memory module as
faulty, swap or replace the module. 8 Reseat the memory modules in the first DIMM socket...
Hardware Owner's Manual (PDF) - Page 143
...Closing the System" on the system and attached peripherals. Troubleshooting a Hot-plug Hard Drive
Problem • Device driver error. • One or more information.
5 Verify that the controller is enabled and the drives appear in their connectors.
f Reconnect the system to the operating system.
4 Ensure that the hard drive has been configured correctly for your system has a SAS RAID...
Hardware Owner's Manual (PDF) - Page 147
...working inside the system. Problem
• Error message indicates a problem with an expansion card. • Expansion card performs incorrectly or not at all. See
"Installing an Expansion Card" on page 151.
Before performing any procedure, see "Getting Help" on the system and
attached peripherals. See "Using Dell PowerEdge Diagnostics" on page 95. 5 Close the system.
Troubleshooting...
Dell PowerEdge R300 Reviews
We have not received any reviews for Dell yet.