Administration Guide
Page 22
... Outbound Proxy to the LAN port is automatically changed to 192.168.1.0. Introducing Cisco Small Business Analog Telephone Adapters ATA Connectivity Requirements 1 SPA2102 Connectivity As shown in the following illustration, the SPA2102 has two FXS ports (voice lines 1 and 2). If there is a... network address 192.168.0.0 with hairpinning) or Broadband modem ISP LAN WAN Internet IP ITSP 187257 SPA2102 Administration PC By default, the device attached to forward all voice traffic when the SPA2102 is located behind a router. Cisco Small Business ATA Administration Guide 22
... Outbound Proxy to the LAN port is automatically changed to 192.168.1.0. Introducing Cisco Small Business Analog Telephone Adapters ATA Connectivity Requirements 1 SPA2102 Connectivity As shown in the following illustration, the SPA2102 has two FXS ports (voice lines 1 and 2). If there is a... network address 192.168.0.0 with hairpinning) or Broadband modem ISP LAN WAN Internet IP ITSP 187257 SPA2102 Administration PC By default, the device attached to forward all voice traffic when the SPA2102 is located behind a router. Cisco Small Business ATA Administration Guide 22
Administration Guide
Page 23
... behind a router. Cisco Small Business ATA Administration Guide 23 Administrative IVR (Line 1 or Line 2) PSTN Line 1 PSTN Line 1 Ethernet port IP Router (with hairpinning) or Broadband modem ISP LAN WAN LAN port Internet IP ITSP 187259 SPA3102 Administration PC By default, the device on... use an Outbound Proxy to forward all voice traffic when the SPA3102 is automatically changed to 192.168.1.0. Introducing Cisco Small Business Analog Telephone Adapters ATA Connectivity Requirements 1 SPA3102 Connectivity As shown in the following figure, the SPA3102 has one ...
... behind a router. Cisco Small Business ATA Administration Guide 23 Administrative IVR (Line 1 or Line 2) PSTN Line 1 PSTN Line 1 Ethernet port IP Router (with hairpinning) or Broadband modem ISP LAN WAN LAN port Internet IP ITSP 187259 SPA3102 Administration PC By default, the device on... use an Outbound Proxy to forward all voice traffic when the SPA3102 is automatically changed to 192.168.1.0. Introducing Cisco Small Business Analog Telephone Adapters ATA Connectivity Requirements 1 SPA3102 Connectivity As shown in the following figure, the SPA3102 has one ...
Administration Guide
Page 24
...NAT/PAT Internal DHCP Line 2 server Ethernet port Line 3 Line 4 AUX port IP Router (with hairpinning) or Broadband modem ISP LAN WAN Administration PC Internet IP ITSP Line 5 Line 6 187256 Line 7 Line 8 By default, the device on the AUX port is assigned the network address 192.168.0.0 ...with a device on the Ethernet port, the network address of eight voice ports (voice lines 1-8). Introducing Cisco Small Business Analog...
...NAT/PAT Internal DHCP Line 2 server Ethernet port Line 3 Line 4 AUX port IP Router (with hairpinning) or Broadband modem ISP LAN WAN Administration PC Internet IP ITSP Line 5 Line 6 187256 Line 7 Line 8 By default, the device on the AUX port is assigned the network address 192.168.0.0 ...with a device on the Ethernet port, the network address of eight voice ports (voice lines 1-8). Introducing Cisco Small Business Analog...
Administration Guide
Page 38
...browser to finish your configuration. Both privileges can be password protected. The device reboots. Click OK to install the latest firmware: a. Cisco Small Business ATA Administration Guide 38 The success window appears when the upgrade is in progress. ATA devices support two levels of the...window, verify that the correct device information and product number appear. In the next window that appears, enter the IP address of the ATA device, the default IP address is announced. Extract the Zip file, and then run the executable file to refresh your ATA device, you...
...browser to finish your configuration. Both privileges can be password protected. The device reboots. Click OK to install the latest firmware: a. Cisco Small Business ATA Administration Guide 38 The success window appears when the upgrade is in progress. ATA devices support two levels of the...window, verify that the correct device information and product number appear. In the next window that appears, enter the IP address of the ATA device, the default IP address is announced. Extract the Zip file, and then run the executable file to refresh your ATA device, you...
Administration Guide
Page 40
...1 Start Internet Explorer, connect to the administration web server, and choose Admin access with Advanced settings. By default, the page is required. STEP 2 Click Network tab > WAN Setup. Cisco Small Business ATA Administration Guide 40 Connect an analog telephone to the Phone 1 port of the ATA device...top right corner of the ATA device. STEP 3 Direct the browser to the IP address of the page. Then click Advanced. STEP 4 The Router > Status page appears. a. Press 110# to step b.) b. c. NOTE By default, no password is in Basic User mode. STEP 1 Start Internet Explorer on ...
...1 Start Internet Explorer, connect to the administration web server, and choose Admin access with Advanced settings. By default, the page is required. STEP 2 Click Network tab > WAN Setup. Cisco Small Business ATA Administration Guide 40 Connect an analog telephone to the Phone 1 port of the ATA device...top right corner of the ATA device. STEP 3 Direct the browser to the IP address of the page. Then click Advanced. STEP 4 The Router > Status page appears. a. Press 110# to step b.) b. c. NOTE By default, no password is in Basic User mode. STEP 1 Start Internet Explorer on ...
Administration Guide
Page 41
... Gateway, and Primary DNS. Cisco Small Business ATA Administration Guide 41 Select DHCP from the Connection Type drop-down menu. In the Static IP Settings section, enter the IP address in the Static IP field, the subnet mask in the NetMask field, and the default gateway IP address in the Primary DNS and... the MAC Clone Settings. (Contact your progress, click the Router tab and then click Status. This is the correct setting for DHCP, static IP addressing, or PPPoE. If your service uses a specific PC MAC address, then select yes from the Connection Type drop-down menu. Then enter...
... Gateway, and Primary DNS. Cisco Small Business ATA Administration Guide 41 Select DHCP from the Connection Type drop-down menu. In the Static IP Settings section, enter the IP address in the Static IP field, the subnet mask in the NetMask field, and the default gateway IP address in the Primary DNS and... the MAC Clone Settings. (Contact your progress, click the Router tab and then click Status. This is the correct setting for DHCP, static IP addressing, or PPPoE. If your service uses a specific PC MAC address, then select yes from the Connection Type drop-down menu. Then enter...
Administration Guide
Page 43
Cisco Small Business ATA Administration Guide 43 Administrator account privilege is No, you upgrade the ATA device to the firmware specified by the URL, which can identify either a TFTP or HTTP server. NOTE If the value of the Upgrade URL is as follows: http://spa-ip-addr/... Rebooting, and Resyncing Your ATA Device 2 Advanced Configurations Other parameters may need to be changed from the defaults, depending on hold. See the "Network Address Translation (NAT) and Voice over IP (VoIP)," on page 61 for the upgrade operation. See the "Secure Call Implementation," on page 71 ...
Cisco Small Business ATA Administration Guide 43 Administrator account privilege is No, you upgrade the ATA device to the firmware specified by the URL, which can identify either a TFTP or HTTP server. NOTE If the value of the Upgrade URL is as follows: http://spa-ip-addr/... Rebooting, and Resyncing Your ATA Device 2 Advanced Configurations Other parameters may need to be changed from the defaults, depending on hold. See the "Network Address Translation (NAT) and Voice over IP (VoIP)," on page 61 for the upgrade operation. See the "Secure Call Implementation," on page 71 ...
Administration Guide
Page 44
...Cisco Small Business ATA Administration Guide 44 The Reboot URL is as server-name. If no parameter follows /resync?, the Profile Rule setting from the Provisioning page is typically the file name of the binary located in a directory on the TFTP or HTTP server. If no port specified, the default ...port of the Resync URL is as follows: http://spa-ip-addr/admin/resync?[[protocol://][server-name[:port]]/profilepathname] NOTE The SPA resyncs only when it is used as follows: ...
...Cisco Small Business ATA Administration Guide 44 The Reboot URL is as server-name. If no parameter follows /resync?, the Profile Rule setting from the Provisioning page is typically the file name of the binary located in a directory on the TFTP or HTTP server. If no port specified, the default ...port of the Resync URL is as follows: http://spa-ip-addr/admin/resync?[[protocol://][server-name[:port]]/profilepathname] NOTE The SPA resyncs only when it is used as follows: ...
Administration Guide
Page 52
... work on your PC that could block the syslog port (port 514 by default). If another packet is sent from the same source IP address and port to a different destination, then a different IP address and port number combination is restrictive because an external host can send a...To enable SIP signalling, complete the following tasks: a. b. This method is used. From the STUN Test Enable field, choose yes. b. b. Cisco Small Business ATA Administration Guide 52 NOTE This procedure assumes that port to the external host. From the Debug level drop-down to receive syslog...
... work on your PC that could block the syslog port (port 514 by default). If another packet is sent from the same source IP address and port to a different destination, then a different IP address and port number combination is restrictive because an external host can send a...To enable SIP signalling, complete the following tasks: a. b. This method is used. From the STUN Test Enable field, choose yes. b. b. Cisco Small Business ATA Administration Guide 52 NOTE This procedure assumes that port to the external host. From the Debug level drop-down to receive syslog...
Administration Guide
Page 55
... adjustment: disable • Call Waiting: no • 3 Way Calling: no Cisco Small Business ATA Administration Guide 55 Configuring Voice Services Using a FAX Machine 4 • G.726-40 • G.729a • G.723 WRTP54G • G.711u (configured by default) • G.711a • G.726-32 • G.729a • G.... over an IP network. STEP 1 Upgrade the ATA firmware to the latest version STEP 2 Ensure that you have approximately 100Kbps. • For T.38, allocate at least 50 kbps. STEP 3 To optimize G.711 fallback fax completion rates, set the following on the SPA2102, SPA3102, ...
... adjustment: disable • Call Waiting: no • 3 Way Calling: no Cisco Small Business ATA Administration Guide 55 Configuring Voice Services Using a FAX Machine 4 • G.726-40 • G.729a • G.723 WRTP54G • G.711u (configured by default) • G.711a • G.726-32 • G.729a • G.... over an IP network. STEP 1 Upgrade the ATA firmware to the latest version STEP 2 Ensure that you have approximately 100Kbps. • For T.38, allocate at least 50 kbps. STEP 3 To optimize G.711 fallback fax completion rates, set the following on the SPA2102, SPA3102, ...
Administration Guide
Page 70
... to the Dial Plan section. STEP 4 Enter the desired values in the Dial Plan field. STEP 1 Start Internet Explorer, and then enter the IP address of this section. STEP 1 Connect to the administration web server, and choose Admin access with Advanced settings. STEP 3 Scroll down to the...Dial Plans You can edit dial plans and can use the following procedure to reset the default timer settings for a particular digit sequence or type of call, you need to the carrier. Cisco Small Business ATA Administration Guide 70 Resetting the Control Timers You can modify the control timers....
... to the Dial Plan section. STEP 4 Enter the desired values in the Dial Plan field. STEP 1 Start Internet Explorer, and then enter the IP address of this section. STEP 1 Connect to the administration web server, and choose Admin access with Advanced settings. STEP 3 Scroll down to the...Dial Plans You can edit dial plans and can use the following procedure to reset the default timer settings for a particular digit sequence or type of call, you need to the carrier. Cisco Small Business ATA Administration Guide 70 Resetting the Control Timers You can modify the control timers....
Administration Guide
Page 83
...which appears both at the top right corner of the trunks by your ITSP, or leave the default setting, unlimited (16 calls). d. In the Contact List field, modify the contact list as needed...the Subscriber Information section. • Display Name: The Caller ID that you want to configure. Cisco Small Business ATA Administration Guide 83 b. e. Trunk Group Management You can connect directly to the ...Trunk Status Page by entering the following URL: http://spa8000-ip-addr/status. See "Contact List for each trunk group that you need to use for...
...which appears both at the top right corner of the trunks by your ITSP, or leave the default setting, unlimited (16 calls). d. In the Contact List field, modify the contact list as needed...the Subscriber Information section. • Display Name: The Caller ID that you want to configure. Cisco Small Business ATA Administration Guide 83 b. e. Trunk Group Management You can connect directly to the ...Trunk Status Page by entering the following URL: http://spa8000-ip-addr/status. See "Contact List for each trunk group that you need to use for...
Administration Guide
Page 86
... page 88 Using the Internal Music Source for Music On Hold An internal music source with a default music file (Romance de Amor). It plays an internally stored music file repeatedly. STEP 1 Use... the phone menu to configure Music on Hold using TFTP. Cisco Small Business ATA Administration Guide 86 Press the Setup button on page 87 Using the .... Press 9 - 5 Configuring Music on Hold This chapter explains how to find the IP address of the phone: a. Current IP Address. This chapter includes the following topics: • "Using the Internal Music Source,"...
... page 88 Using the Internal Music Source for Music On Hold An internal music source with a default music file (Romance de Amor). It plays an internally stored music file repeatedly. STEP 1 Use... the phone menu to configure Music on Hold using TFTP. Cisco Small Business ATA Administration Guide 86 Press the Setup button on page 87 Using the .... Press 9 - 5 Configuring Music on Hold This chapter explains how to find the IP address of the phone: a. Current IP Address. This chapter includes the following topics: • "Using the Internal Music Source,"...
Administration Guide
Page 87
...the Internal Music Source The following resources are using as the TFTP server • port: The port number used by the TFTP server (default 69) Cisco Small Business ATA Administration Guide 87 The Telephone Configuration page appears in the MOH Server field: imusic STEP 7 Click Submit All Changes. STEP... at 8000 samples/sec, up to 65.5 seconds in the Internal Music URL field: tftp://server_IPaddress:portpath • server_IPaddress: The local IP address of the computer you are required to change the music file for the internal music source: • TFTP server software • The...
...the Internal Music Source The following resources are using as the TFTP server • port: The port number used by the TFTP server (default 69) Cisco Small Business ATA Administration Guide 87 The Telephone Configuration page appears in the MOH Server field: imusic STEP 7 Click Submit All Changes. STEP... at 8000 samples/sec, up to 65.5 seconds in the Internal Music URL field: tftp://server_IPaddress:portpath • server_IPaddress: The local IP address of the computer you are required to change the music file for the internal music source: • TFTP server software • The...
Administration Guide
Page 97
...gateway • nat: Enable or disable NAT mapping when calling the gateway The following table lists some examples. In general, you can specify any IP address that can specify Gateways 1 to use gwx (x = 0,1,2,3,4) when making certain calls. You can be routed to any gateway address in ...the dial plan to 4 in a dial plan by default. In addition, three parameters are added that the user enters. Also, gw0 represents the internal PSTN gateway via the FXO port. These settings are ...
...gateway • nat: Enable or disable NAT mapping when calling the gateway The following table lists some examples. In general, you can specify any IP address that can specify Gateways 1 to use gwx (x = 0,1,2,3,4) when making certain calls. You can be routed to any gateway address in ...the dial plan to 4 in a dial plan by default. In addition, three parameters are added that the user enters. Also, gw0 represents the internal PSTN gateway via the FXO port. These settings are ...
Administration Guide
Page 103
The default VoIP caller dial plan is used in this case, you must select the PIN ..., using one of the VoIP Access List patterns. On SPA8800, the same parameters are set to two-stage dialing. Cisco Small Business ATA Administration Guide 103 Call Forwarding to PSTN Gateway (SPA3102 and SPA8800) This section describes a number of the...need to authenticate the VoIP caller in this scenario. Authentication is performed when the method is none or when the source IP address of a VoIP-ToPSTN call. Forward-On-No-Answer to the PSTN Gateway. The scenario is implemented by setting ...
The default VoIP caller dial plan is used in this case, you must select the PIN ..., using one of the VoIP Access List patterns. On SPA8800, the same parameters are set to two-stage dialing. Cisco Small Business ATA Administration Guide 103 Call Forwarding to PSTN Gateway (SPA3102 and SPA8800) This section describes a number of the...need to authenticate the VoIP caller in this scenario. Authentication is performed when the method is none or when the source IP address of a VoIP-ToPSTN call. Forward-On-No-Answer to the PSTN Gateway. The scenario is implemented by setting ...
Administration Guide
Page 106
... the ATA device. for example, 25 days and 18:12:36. WAN Connection Type The connection type: DHCP or Static IP. Current IP The current IP address assigned to the ATA device. Current Netmask The network mask assigned to the ATA device. MAC address of the ATA ... Version MAC Address Client Certificate Customization Model number of the system; Current Gateway The default router assigned to the ATA device. Primary DNS The primary DNS server assigned to the ATA device. Cisco Small Business ATA Administration Guide 106 Router tab > Status page > System Status section...
... the ATA device. for example, 25 days and 18:12:36. WAN Connection Type The connection type: DHCP or Static IP. Current IP The current IP address assigned to the ATA device. Current Netmask The network mask assigned to the ATA device. MAC address of the ATA ... Version MAC Address Client Certificate Customization Model number of the system; Current Gateway The default router assigned to the ATA device. Primary DNS The primary DNS server assigned to the ATA device. Cisco Small Business ATA Administration Guide 106 Router tab > Status page > System Status section...
Administration Guide
Page 108
... Status page A Router tab > WAN Setup page > Static IP Settings section Static IP NetMask Gateway Static IP address of ATA device, which takes effect if DHCP is 255.255.255.0. The default is disabled. PPPoE Login Password The password assigned by ATA device when DHCP is disabled. Cisco Small Business ATA Administration Guide 108 The...
... Status page A Router tab > WAN Setup page > Static IP Settings section Static IP NetMask Gateway Static IP address of ATA device, which takes effect if DHCP is 255.255.255.0. The default is disabled. PPPoE Login Password The password assigned by ATA device when DHCP is disabled. Cisco Small Business ATA Administration Guide 108 The...
Administration Guide
Page 109
...DNS server. When DHCP is disabled, enter the primary DNS server. Cisco Small Business ATA Administration Guide 109 The default is 0.0.0.0. Sets the secondary DNS server to DHCP-supplied DNS servers. Secondary NTP Server The IP address or name of the ATA device. NOTE: With parallel DNS ...enabled, you can enter the IP address of a primary or secondary DNS server in addition to take over if problems are discovered with the Primary DNS server. The mode of the ATA device. DNS Service Order DNS Query Mode The default is 0.0.0.0. ATA Routing Field Reference...
...DNS server. When DHCP is disabled, enter the primary DNS server. Cisco Small Business ATA Administration Guide 109 The default is 0.0.0.0. Sets the secondary DNS server to DHCP-supplied DNS servers. Secondary NTP Server The IP address or name of the ATA device. NOTE: With parallel DNS ...enabled, you can enter the IP address of a primary or secondary DNS server in addition to take over if problems are discovered with the Primary DNS server. The mode of the ATA device. DNS Service Order DNS Query Mode The default is 0.0.0.0. ATA Routing Field Reference...
Administration Guide
Page 111
...Status page You can use the LAN Status page to a switch that uses VLAN tagging. Bridge-The unit acts as a router and provides IP addresses to PCs attached to the LAN port. ATA Routing Field Reference LAN Status page A Maximum Uplink Speed The maximum bandwidth for the VLAN ... > VLAN Settings section Enable VLAN VLAN ID Allows (yes) or prevents (no) VLAN access. Cisco Small Business ATA Administration Guide 111 NOTE: Choose yes if your ATA device is 128 kbps. The default is connected to view the LAN settings. This page includes the following sections: • "Networking ...
...Status page You can use the LAN Status page to a switch that uses VLAN tagging. Bridge-The unit acts as a router and provides IP addresses to PCs attached to the LAN port. ATA Routing Field Reference LAN Status page A Maximum Uplink Speed The maximum bandwidth for the VLAN ... > VLAN Settings section Enable VLAN VLAN ID Allows (yes) or prevents (no) VLAN access. Cisco Small Business ATA Administration Guide 111 NOTE: Choose yes if your ATA device is 128 kbps. The default is connected to view the LAN settings. This page includes the following sections: • "Networking ...