Cisco SPA2102-EU Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco SPA2102-EU manuals!
Problems with Cisco SPA2102-EU?
Ask a Question
Free Cisco SPA2102-EU manuals!
Problems with Cisco SPA2102-EU?
Ask a Question
Cisco SPA2102-EU Videos
Xnet New Zealand - Cisco / Linksys SPA2102 Phone Adapter Router Setup
Duration: 1:16
Total Views: 2,053
Duration: 1:16
Total Views: 2,053
Configuracion Web Gateway de Voz Cisco SPA2102
Duration: 1:30
Total Views: 386
Duration: 1:30
Total Views: 386
Configuracion Web Adaptador Telefonico Cisco SPA2102
Duration: 2:20
Total Views: 365
Duration: 2:20
Total Views: 365
WXC Communications NZ - Cisco / Linksys SPA2102 Phone Adapter Router Setup
Duration: 1:11
Total Views: 26
Duration: 1:11
Total Views: 26
Popular Cisco SPA2102-EU Manual Pages
Administration Guide - Page 8
...) Dial Plan section FXS Port Polarity Configuration section VoIP-to-PSTN Gateway Setup section (SPA8800) PSTN-To-VoIP Gateway Setup section (SPA8800) FXO Timer Values (sec) section (SPA8800) PSTN Disconnect Detection section (SPA8800) International Control section (SPA8800) Call Forward, Speed Dial, Supplementary Services, and Ring Settings (SPA8000 and SPA8800)
Trunk Group page (SPA8000)
Line...
Administration Guide - Page 37
... the
Integrated Access Device, network switch, router, and PoE switch to ensure that you downloaded previously. Upgrading the Firmware for the SPA9000 Voice System. Press **** on the ATA device. (You may not hear a dial tone.
Basic Installation and Configuration
See your the Quick Installation Guide and the User Guide for the ATA model that you are configuring the complete SPA9000...
Administration Guide - Page 40
... address. Press 110# to access the IVR menu.
Setting Up the WAN Configuration for your Quick Installation Guide or User Guide for Your ATA Device
STEP 1 Start Internet Explorer,... Guide.
Then click Advanced.
Cisco Small Business ATA Administration Guide
40 STEP 4 The Router > Status page appears.
a. NOTE By default, no password is in Basic User mode. By default,...
Administration Guide - Page 49
... Address Translation (NAT) and Voice over IP (VoIP)
3
STEP 3 Scroll down to the NAT Settings section.
• NAT Mapping Enable: Choose YES. • NAT Keep Alive Enable: Choose YES (optional).
Configuring Your System for your router to allow SIP traffic. See "Firewalls and SIP," on your router. Voice tab > SIP: NAT Support Parameters
STEP 4 Click Voice tab > Line N, where...
Administration Guide - Page 102
... the dial plan after the VoIP call leg is auto-dialed by the caller is dialed to the PSTN. The caller does not hear the PSTN dial tone (except for a little leakage before the first digit of the INVITE, computed with the auth-ID and password using MD5. This rule applies regardless of the...
Administration Guide - Page 110
... feature. Options are Yes or No.
Router tab > WAN Setup page >
QOS Settings section
Use Quality of Service (QoS) to assign different priority levels to access the Internet. Enable MAC Clone Service
Cloned MAC Address
To use QoS. Options are None or TBF (token bucket filter). Default is 80. The default value is not directly connected to...
Administration Guide - Page 126
..., which logs debug information.
Cisco Small Business ATA Administration Guide
126 ATA Voice Field Reference
System page
B
DNS Server Order DNS Query Mode
Specifies the method for logging ATA device system information and critical events. Do parallel or sequential DNS Query. Syslog Server Debug Server Debug Level
The default is accepted by the ATA...
Administration Guide - Page 132
...default is 16384. Voice tab > SIP page >
RTP Parameters section
RTP Port Min
Minimum port number for RTP transmission and reception.
RTP Packet Size
The default is 0. Cisco Small Business ATA Administration Guide
...and reception. The default is 16482.
Packet size in seconds, which to play the SIT4 Tone. If value is 0.030.
Max RTP ICMP Err
The default is set to 0, the ATA...
Administration Guide - Page 160
....
• On the SPA2102, refer to the Line pages and the corresponding User pages. • On the SPA8800, refer to the Phone pages 1 to 4 to configure the settings for
the Phone (FXS) ports 1 to configure the settings for voice service. Refer to the Line pages to 4. NOTE Depending on the ATA model, some variations, depending on...
Administration Guide - Page 161
... (for service, select yes.
For example, the SPA2102 provides two Line tabs (Line 1 and Line 2), while the SPA8000 provides eight tabs (Line1 through Line 8). The default is available on page 189
In a configuration profile, the Line parameters must be appended with the model of the ATA device. Cisco Small Business ATA Administration Guide
161 The default is...
Administration Guide - Page 162
... SPA8800, these settings are configured on the Phone pages only. SAS Enable
SAS DLG Refresh Intvl
To enable the use of the line as a streaming audio source, select yes.
Otherwise, select no .
If the caller does not respond to the caller is still active. The default is not zero, it auto-answers incoming calls...
Administration Guide - Page 168
... . This field is found on the Phone pages only.
Voice tab > Line page >
Call Feature Settings section
On the SPA8800, these settings are configured on the SPA2102 only. Otherwise, select no . MOH Server
Conference Bridge URL
The default is yes.
This feature supports external conference bridging for example, [email protected]:12345 or conf (which uses...
Administration Guide - Page 189
... SPA8000 and the SPA8800, you can configure settings for mA are {3.1, 3.2, 3.35, 3.5} (V). Cisco Small Business ATA Administration Guide
189
The default is no.
On-Hook Speed
The default is 512ms. Choices for call forward, speed dial, and supplementary services, as well as ring settings.
Operational Loop Current Min
Ring Timeout
The default is 640 ms.
Choose from {High...
Administration Guide - Page 199
... (SPA3102) >
Line Enable section
Line Enable
To enable this line for service, select yes. PSTN Contact List
The default is Phone1+2. The default is yes.
Cisco Small Business ATA Administration Guide
199 Voice tab > PSTN Line page (SPA3102) >
NAT Settings section
NAT Mapping Enable
To use externally mapped IP addresses and SIP/RTP ports in SIP messages, select yes...
Administration Guide - Page 239
...Phone User Guide
• Phone setup • Phone features
VARs and phone endusers
• SPA9x2 series IP
phones
Analog Telephone Adapter Administration Guide
• Administration and use
of Cisco Small Business ATAs
• PAP2T, SPA2102,
SPA3102, SPA8000, and WRTP54G
VARs, system administrators, and Service Providers
User Guide for switch
User Guide for router
Cisco Small Business...
Cisco SPA2102-EU Reviews
We have not received any reviews for Cisco yet.