Cisco WAP200E-EU - Small Business Wireless-G Exterior Access Point Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WAP200E-EU manuals!
Problems with Cisco WAP200E-EU?
Ask a Question
Free Cisco WAP200E-EU manuals!
Problems with Cisco WAP200E-EU?
Ask a Question
Most Recent Cisco WAP200E-EU Questions
How Can I Connect 3 Wap200e Devices To Client Wireless
I have 3 SB 200E how do i use it to link three buildings together. My computers are already running ...
I have 3 SB 200E how do i use it to link three buildings together. My computers are already running ...
(Posted by tasminor 12 years ago)
Popular Cisco WAP200E-EU Manual Pages
User Guide - Page 1
Wireless-G Exterior Access Point with Power Over Ethernet
Model: WAP200E
USER GUIDE BUSINESS SERIES
User Guide - Page 3
...Setup 8 Wireless 8 AP Mode 9 Administration 9 Status 9
Chapter 6: Advanced Configuration
10
Web-Based Utility 10 Setup > Basic Setup 10
Setup 10 Network Setup 10 Setup > Time 11 Time 11 Wireless > Basic Wireless Settings 11 Basic Settings 11 Wireless > Wireless Security 12 Wireless Security 12 Wireless > Wireless Connection Control 15
Wireless-G Exterior Access Point with Power...
User Guide - Page 7
... you can communicate with each other . Network Layout
The Access Point has been designed for use of an access point. This network will greatly enhance performance.
Roaming
Infrastructure mode also supports roaming capabilities for your desktop PCs, and USB Adapters.
An infrastructure configuration extends the accessibility of a wireless PC to the switch. Example of a Simple...
User Guide - Page 13
... the VLAN and QoS related settings for the Access Point. Enter admin in 192.168.1.0/24 subnet.
The following steps:
1. Setup
Basic Setup Enter the Host Name and IP Address settings on this screen. wireless-G), wireless channel, and SSID configuration on your Injector to assign the IP address in the User Name field. Advanced Wireless Settings Use this screen to change default...
User Guide - Page 14
.... Firmware Upgrade Upgrade the Access Point's firmware on this screen. Status
You will use the Administration tabs to customize the password and Simple Network Management Protocol (SNMP) settings. Wireless This screen displays wireless network settings including SSID, network mode, and wireless channel. Log Configure the Log settings for the Access Point on this screen. Factory Default...
User Guide - Page 15
... if the Access Point is configured to acquire the IP address through the network if DNS has been set on the LAN that your router.
10
Address Bar
NOTE: The default IP address is WAP200E. You can be the same as
that case, Linksys recommends to the Access Point. • LocalIPAddress TheIPaddressmustbeuniquetoyour
network.
Wireless-G Exterior Access Point with Power Over Ethernet
Setup...
User Guide - Page 16
... can be connected at Wireless-G data rates. Auto channel selection will start when you are in using the Access Point in this screen. Automatic Configuration - Setup > Time
Time
You can set the date and time manually. Default is to set the time either manually or automatically from a time server if the Access Point can be connected to the Access Point, the select this option...
User Guide - Page 19
... IEEE 802.11.
A RADIUS server is used by the Access Point and RADIUS server. The default is used by the RADIUS server.
Chapter 6
Advanced Configuration
Wireless > Wireless Security > WPA2-Enterprise
RADIUS Server IP Address Enter the RADIUS server's IP address. The default is 3600 seconds. Encryption Mixed Mode automatically chooses TKIP or AES for data encryption. RADIUS Server...
User Guide - Page 20
... hex digits).
Chapter 6
Advanced Configuration
Wireless > Wireless Connection Control
This screen allows you to configure the Connection Control List to either Open System or Shared Key. Each WEP key can connect to the Access Point. The default is available on the right side of each client, the Access Point provides a convenient way to select a specific client device from the table...
User Guide - Page 21
... can be decoded by the Access Point to configure the advanced settings for transmitting control frames, broadcast/ multicast frames, or ACK frames.
Keep the default setting, Auto, so the Access Point can use the All (G-only mode) setting to other wireless devices as needed, when the Wireless-G products are recommended. Select Disabled if you can support.
A beacon is picked from...
User Guide - Page 22
... can set default VLAN (PVID) to 1 untagged, while General port mode can limit the maximum data rate used in your environment. Chapter 6
Advanced Configuration
Wireless > VLAN & QoS
This screen allows you to configure the VLAN and QoS related settings for the default VLAN ID. VLAN Select Enabled if you want to your Access Point will be accessible from the wired LAN. Your Access Point...
User Guide - Page 23
... will have its signal. Wireless Repeater When set to Wireless Repeater mode, the Wireless Repeater is set to a wired network.
Desktop Laptop
Access Point - MAC Address
The MAC address of your wireless PCs to Access Point by default. In most cases, no change the Access Point's mode of the access point manually. AP Mode
The Access Point offers three modes of this option if...
User Guide - Page 26
...are experiencing problems with Power Over Ethernet
21 Help information is available on the right side of the screen. Wireless-G Exterior Access Point with the Access Point or the new firmware has a feature you upgrade the Access Point's firmware, note all of the firmware upgrade file in a few seconds. Restore Factory Defaults To restore the Access Point's factory default settings, click...
User Guide - Page 33
...to intruders than a network encrypted with specific MAC addresses. Wireless-G Exterior Access Point with WPA/WPA2 is admin. Wi-Fi Protected Access (WPA/WPA2) and Wired Equivalency Privacy (WEP) offer different levels of security for wireless networks.
2.
Change the default wireless network name or SSID
Wireless devices have a default password set by the factory. To protect the...
User Guide - Page 38
... (QoS priority), 802.1Q (VLAN), 802.1X (Security Authentication), 802.11i - Ready (Security WPA2), 802.11e - TKIP/AES
WPA2 bits & params 256 - Ready (WMM & U-APSD), 802.11F (Wireless Roaming) 1 Ethernet, 1 External Antenna Reset UTP CAT 5 Power, Ethernet, Wireless Linux
1, 2 and 2c
Access Point Mode, point-to-point Bridge Mode, point-to-multipoint Bridge Mode, Repeater Mode
802.11b/DSSS, 11g...
Cisco WAP200E-EU Reviews
We have not received any reviews for Cisco yet.