Weider 9350 Support and Manuals
Get Help and Manuals for this Weider item
Popular Weider 9350 Manual Pages
Instruction Manual - Page 1
... ordering replacement parts:
• the MODEL NUMBER of the product (WEEVSY59230)
• the NAME of the product (WEIDER® PRO 9350 weight system)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in the centre of this manual)
Part No...
Instruction Manual - Page 2
... of calf)
WEIDER is an effective way to make exercise a regular and enjoyable part of arm) D. out. • Rest for 30 seconds after each set for both your...TROUBLESHOOTING AND MAINTENANCE 24 CABLE DIAGRAMS 25 EXERCISE GUIDELINES 26 ORDERING REPLACEMENT PARTS Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are : • Rest for three minutes after each set...
Instruction Manual - Page 3
.... Proper breathing is intended for persons over the age of repetitions or sets per- Read all parts are on the foot plate when performing an exercise that the cables are properly tightened each set . The weight system is important. Make sure all instructions in this manual and in the indicated location.
6. Always stand on all...
Instruction Manual - Page 4
... correctly routed, the weight system will help us assist you have questions after the parts that are determined relative to develop every major muscle group of the High Cable (11...versatile WEIDER® PRO 9350 weight system. The model number is to tone your body, build dramatic muscle size and strength, or improve your benefit, read this manual, please call our Customer Service Department...
Instruction Manual - Page 5
...the Pulley and the Pulley Covers to a higher set of the weight system, the assembly process will...Select a Location for Yourself
Everything in this manual.
24
ASSEMBLY
Make Assembly Easier for the ...part is used in assembly, we have questions after reading the assembly instructions, please call our Customer Service Department at the weight stack in the same manner. Replace any worn parts...
Instruction Manual - Page 6
... height. Weight resistance shown for the butterfly arm station is loose, and pull it out as far as friction between the cables, pulleys, and weight guides.
Press two M10 Round Bushings (96) into an adjustment hole in the box on the floor. Slide the Carriage up through the Base (4) and the...
Instruction Manual - Page 7
... TO THE LOW CABLE
To use , and replace the 38mm Square Inner Cap (32). Remove the 38mm Square Inner Cap (32) from the Seat Frame. Attach the Support Upright (88) to the Carriage (89) with...attached to pivot easily.
Always remove the Curl Pad (24) when it will go.
Make
sure the Support Upright leans toward the
center of the Chain to the indicated Eyebolt (109) on the Upright as it...
Instruction Manual - Page 8
... an M10 x 155mm Bolt (60), two M10 Washers (9), two 15mm Spacers (61), and an M10 Nylon Locknut (21). Replace any worn parts immediately.
The weight setting of resistance at each exercise. Secure the Weight Guides (62) to see drawing 6) are properly tightened each exercise station may vary from your exercise program.
Also, refer to...
Instruction Manual - Page 9
...If the cables are not properly installed, they may be damaged when ...and between the Weight Guides (62).
Note: Make sure that all parts have been properly ...tightened. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly, find and correct the problem...If there is used. see TROUBLESHOOTING AND MAINTENANCE on page 25...
Instruction Manual - Page 11
...
83
Small
40
Tab
15
40
106
21
5
21 93
40
Small Tab
83 15 40
44.
the pulleys must be able to the first set of Pulley
Covers (40) inside the other . Locate the High Cable (11), which has a ball on one end and an eyelet on the Right
Upright...
Instruction Manual - Page 14
... and an M10 Nylon Locknut
(21). Attach the Pulley and a pair of Pulley
Covers (40) to the second set of holes from the
top of Pulley
Covers (40) to the Pulley Plates (58) with an
M10 x 52mm...and Left Upright Brackets (93, 94) between the Top Frame (55), the Carriage Upright (84) and the Support Upright (88). Rest the Cable in the bracket on
30
one end.
26. it should fit over the ...
Instruction Manual - Page 15
... Cap (44)
60mm Square Inner Cap (101)
This chart is provided to help you cannot find a part in the parts bags, check to the key number of the part from the PART LIST in the centre of this manual. The number in parenthesis below each stage is divided into four stages: 1) frame assembly, 2) arm assembly...
Instruction Manual - Page 16
PART IDENTIFICATION CHART-Model No. WEEVSY59230
R1203A
M10 Nylon Locknut (21) M8 Nylon Locknut (3)
M10 x 45mm Bolt (100) M8 x 45mm Bolt (66)
M10 x 22mm Bolt (98)
M10 x 47mm Bolt (...
Instruction Manual - Page 17
PART LIST-Model No.
Qty.
58
2
59...Upright Locking Bar Lock Bumper Support Upright Carriage Large "U"-bracket ...Manual Exercise Guide Exercise Chart Decal Grease Pack
REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL. See the back cover of the user's manual for information about ordering replacement parts.
81 SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
Note: Specifications...
Instruction Manual - Page 18
... 40
4
14
96 40
28
32
34
30
21
34 30
92
67 31
31
19
53
19
69 100
96 21 27
1 EXPLODED DRAWING-Model No.
Weider 9350 Reviews
We have not received any reviews for Weider yet.