XE-A202 Operation Manual in English and Spanish
Page 2
... accessible. Model Number Serial Number Date of Purchase Place of the FCC Rules. Note: This equipment has been tested and found to comply with the instruction manual, may cause harmful interference to Part 15 of Purchase
... accessible. Model Number Serial Number Date of Purchase Place of the FCC Rules. Note: This equipment has been tested and found to comply with the instruction manual, may cause harmful interference to Part 15 of Purchase
XE-A202 Operation Manual in English and Spanish
Page 11
... 1" section (Job code 6) for changing the printing style. 5 Programming date, time and tax The cash register provides text languages of the inner cover, and F replace the printer cover. Before you can proceed with registration of the arm as instructed above. 5. 4. Press the key to take -up excess slack in "Various Function Selection Programming...
... 1" section (Job code 6) for changing the printing style. 5 Programming date, time and tax The cash register provides text languages of the inner cover, and F replace the printer cover. Before you can proceed with registration of the arm as instructed above. 5. 4. Press the key to take -up excess slack in "Various Function Selection Programming...
XE-A202 Operation Manual in English and Spanish
Page 67
.... 2. The paper will be convenient to a position other than OFF with the paper positioning guides. 6. While holding down the paper, slowly close the arm as instructed above. 7. Insert the end of receipts. Replace the printer cover. Installing the journal paper roll: 1. F 7. Make sure securely you push down the center of the...
.... 2. The paper will be convenient to a position other than OFF with the paper positioning guides. 6. While holding down the paper, slowly close the arm as instructed above. 7. Insert the end of receipts. Replace the printer cover. Installing the journal paper roll: 1. F 7. Make sure securely you push down the center of the...
XE-A202 Operation Manual in English and Spanish
Page 70
...;C) Electronics: LSI (CPU) etc. Use these labels with the department keys. diam.: 3.15 in (57.5 ± 0.5 mm) Max. Write department names on the labels and attach them to the department keys by 7.7 W Operating 30 W (max.) Working temperature: 32 °F to 104 °F (0 °C to change without notice for improvement. SPECIFICATIONS Model: XE-A202...
...;C) Electronics: LSI (CPU) etc. Use these labels with the department keys. diam.: 3.15 in (57.5 ± 0.5 mm) Max. Write department names on the labels and attach them to the department keys by 7.7 W Operating 30 W (max.) Working temperature: 32 °F to 104 °F (0 °C to change without notice for improvement. SPECIFICATIONS Model: XE-A202...
Quick Installation Guide
Page 1
... be placed. • Peel off the adhesive tape on the display will sound 3 times. Important Notice The cash register will operate correctly only after pulling out the plug, and insert the plug again. Model XE-A202 For quick set the mode switch to REG position. • Lift the rear of the...using the fixing angle bracket provided with the power cord connected and set -up, follow the steps. For further information, please read the instruction manual. NOTE: If the buzzer does not sound when the plug is located at least one minute after the following PGM procedure. •...
... be placed. • Peel off the adhesive tape on the display will sound 3 times. Important Notice The cash register will operate correctly only after pulling out the plug, and insert the plug again. Model XE-A202 For quick set the mode switch to REG position. • Lift the rear of the...using the fixing angle bracket provided with the power cord connected and set -up, follow the steps. For further information, please read the instruction manual. NOTE: If the buzzer does not sound when the plug is located at least one minute after the following PGM procedure. •...
Quick Installation Guide
Page 2
... take up the print roller release lever to make sure the paper end comes out of the paper along with the paper positioning guides as instructed above. 2. 3. 5. Example: Time (2:30pm) 1 4 2 0 #/TM/ST . Press the key to unlock and open the arm, and close the print roller arm, and push down the...
... take up the print roller release lever to make sure the paper end comes out of the paper along with the paper positioning guides as instructed above. 2. 3. 5. Example: Time (2:30pm) 1 4 2 0 #/TM/ST . Press the key to unlock and open the arm, and close the print roller arm, and push down the...
Quick Installation Guide
Page 4
...OPX/Z MGR X1/Z1 X2/Z2 PGM Mode Lock 10 Reporting The cash register has two reporting types. The reports can be taken in the X1/...stage to finalise. • Return to the REG position. Use the resetting function (Z) when you need to clear the registers memory. message and press #/TM/ST . • Press 3 (for line 2) followed by . • Type ...2 (for line 3) followed by . • Type in your 24 character max. For further information please refer to the instruction manual. 9 Programming A Receipt Message Insert the manager (MA) key into the Mode Lock and turn to X1/Z1. •...
...OPX/Z MGR X1/Z1 X2/Z2 PGM Mode Lock 10 Reporting The cash register has two reporting types. The reports can be taken in the X1/...stage to finalise. • Return to the REG position. Use the resetting function (Z) when you need to clear the registers memory. message and press #/TM/ST . • Press 3 (for line 2) followed by . • Type ...2 (for line 3) followed by . • Type in your 24 character max. For further information please refer to the instruction manual. 9 Programming A Receipt Message Insert the manager (MA) key into the Mode Lock and turn to X1/Z1. •...