Oki RT322SK Support and Manuals
Get Help and Manuals for this Oki Data item
Popular Oki RT322SK Manual Pages
RT322 Users Guide - Page 3
Choosing a place for the printer
2. Parts Identification and Nomenclature 2-1. Setup... 3-1. Errors... 6-3. Specifications...32 10-1. Interface...32 10-4. Parallel Interface Model...37 11-2. Installing the Printer Software... 3-4. Preventing Paper Jams...29 8-2. Cleaning the Rubber Roller...31 9-3. Environmental Requirements...34 10-6. RS-232C ...
RT322 Users Guide - Page 10
Interface Cable
(1) Make sure the printer is turned off . (2) Attach the ferrite core to the cable as shown in
the illustration
(3) Pass the cable through the cable support as shown.
3-2-4. Interface Cable (1) Make sure the printer is turned off . (2) Attach the ferrite core to the Ethernet cable.
(3)
10
3-2-3.
RT322 Users Guide - Page 15
...
Tear Bar Model When using a paper roll with an 57.5 mm width, install the paper roll holder as it will cause the paper to close. Note: Make sure that matches the printer's specification. CAUTION
Do...closed after turning on the power, the cutter operates automatically and the front end of the roll, set the paper roll into the hollow, and pull on the following page.
1) Push the cover open...
RT322 Users Guide - Page 16
...manual located in the "Documents" folders on the CD-ROM. 1 Insert the paper guide along the groove in direct contact with a width of 79.5 mm. (This is because the printer head has deteriorated as shown.
Paper Guide
2 Insert the paper guide...the setting at memory switch configuration Utility. A
Note: After using a paper roll with 57.5 mm width, install the supplied paper guide on the setting ...
RT322 Users Guide - Page 17
...thermal head heating element. 6) There is a risk of damage to the driver IC of thermal paper may become electrically charged. Please exercise caution. 8)...outlet slot. Do not touch it, as you could cause a problem if you not put your hand in the paper outlet slot while...very hot.
This can be opened when replacing the paper. To detach a connector, make sure to the ...
RT322 Users Guide - Page 19
... screws that were supplied to secure it in place.
(2) Position the printer over the screws, etc., on the wall and then slide it downward to set it in place.
(3) Push the cover open lever, and open the printer cover.
(4) Insert the roll paper as shown.
19 4.
RT322 Users Guide - Page 23
... reader or scanner is able to the printer, fire or electric shock. Model name: PS60A-24A
Input:
90 to 264 V AC, 50/60 Hz...sec. Max.)
23 Please consult the dealer for printing darkness. To change the
settings for details. 2) The print density may vary depending on the print density. ... may be able to scan a printed bar code or characters depending on the type of paper roll and ...
RT322 Users Guide - Page 25
..., turn the power OFF immediately. 2) When Power supply error occurs, there is not a recoverable error. This is a possibility that the power supply unit has
a trouble.
2) Non-recoverable errors
Error Description
POWER Lamp
Flash access error
OFF
EEPROM error
OFF
SRAM error
OFF
Head thermistor error
OFF
Power voltage error
OFF
ERROR Lamp
Flashes at 0.5second intervals
Flashes at...
RT322 Users Guide - Page 26
... printer enters the Hexadecimal Dump Mode. This function allows you to check if a control code sent to turn off the printer completely.
26 Turn the power ON while holding the FEED button. No., DIP switch settings, and memory switch settings, etc.
6-3-2. However, if the FEED button is pushed, the final line is correct...
RT322 Users Guide - Page 36
...Replace the DIP switch blind. Dip Switch Setting
Two DIP switches are provided at the bottom of the printer, and can be set as given in the illustration below . Make sure the printer is recommended to use a pointed item like a pen or flat-blade driver... screw to on DIP switches. 1. The new settings take off . 2. It is turned off the DIP ...
RT322 Users Guide - Page 37
...Model
ON
ON
OFF No. 1 2 3 4 5 6 7 8
DIP-SW 1
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 ON OFF
DIP-SW 1
The factory settings of switches 1-2 through 1-8 will change according to the command emulation that has been set using switch 1-1.
(1) Star mode
Switch
Function
1-1
Command emulation
1-2
Should not be changed (Should be set... be changed (Should be set to on)
1-4
Sensor adjustment
1-5...
RT322 Users Guide - Page 39
RS-232C Interface Model
ON
ON
OFF No. 1 2 3 4 5 6 7 8
DIP-SW 1
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 ON OFF
DIP-SW 1
The factory settings of switches 1-2 through 1-8 will change according to the command emulation that has been set using switche 1-1.
(1) Star mode
Switch
Function
1-1
Command emulation
1-2
Should not be changed (Should be set to on)
1-3
Should not...
RT322 Users Guide - Page 48
To drive them
continuously, set the duty cycle ratio to the separate Programmer's Manual for diodes D1 and D2 (Ta = 25°C) are :
Collector current IC = 2.0 A
48 It could damage the connected
device and the printer circuit. Refer to the separate Programmer's Manual for coils L1 and L2 is available as a
cash drawer) other...
RT322 Users Guide - Page 50
...*
1-6
USB mode*
1-7
Automatic status back function**
1-9
Shoild always be set to ON. Switch 1-2 on the tear model is 0. DIP SW-2
Switch
Function
ON
OFF
2-1, 2-2, 2-3. 2-4 Always ON Valid
Invalid
Note: The factory settings for DIP switch 1 in the auto cutter model are enabled only when the firmware of the USB interface board is USB 2.00 or...
RT322 Users Guide - Page 52
DIP SW-2
Switch 2-1, 2-2, 2-3. 2-4
Function Always ON
ON Valid
OFF Invalid
Note: The: factory settings for DIP switch 1 in the auto cutter model are set to ON.
Switch 1-3 on the tear model is ON.
52 Appendix B: Ethernet Interface
DIP Switch Settings
ON/ACTIVADO OFF/ DESACTIVADO
DIP SW-1
ON/ACTIVADO OFF/ DESACTIVADO
DIP SW-2
DIP SW-1
Switch
Function...
Oki RT322SK Reviews
We have not received any reviews for Oki yet.