Oki LE840Ts Support and Manuals
Get Help and Manuals for this Oki Data item
Popular Oki LE840Ts Manual Pages
Users Guide - Page 8
......E2-29 2.6.9 System Mode ...E2-30 2.6.10 Interface Setting ...E2-31 2.6.11 Real Time Clock (RTC E2-38 2.6.12 Copying Data to/from USB Memory E2-39
2.7 Installing the Printer Drivers E2-41 2.7.1 Introduction...E2-41 2.7.2 General Description E2-41 2.7.3 Installing the Printer Driver E2-42 2.7.4 Installation under Windows XP/Server 2003/Vista/ Server 2008/7/Server2008...
Users Guide - Page 15
PRINTER SETUP
2. Setup Flow
Procedure
Reference
Installation
After referring to the Safety Precautions in this manual, install the printer in the system mode. 2.6 Printer Setting
Installing the printer driver
Print test Position and Print Tone Fine
adjustment Automatic threshold setting
Manual threshold setting
If necessary, install the printer driver on your host computer.
2.7 Installing...
Users Guide - Page 35
... end is detected in the middle of error, use the printer as a web printer. PRINTER SETUP
2.6.2 Parameter Setting (Cont.)
NOTE: Since detecting the remaining...specification of printing, the printer prints the half-finished label as far as a guide. When the web printer is enabled, the status of this parameter. For details, refer to the External Equipment Interface Manual.
2.6 Printer Setting...
Users Guide - Page 58
....
(9) If the [Connect cable] screen appears, connect the PC and printer, and then turn the printer's power on [Next].
2.7 Installing the Printer Drivers
(8) A screen appears indicating that the installation is complete. PRINTER SETUP
(7) If the [Printer name] screen appears, set the default printer and printer name if necessary, and then click on .
(10) When the...
Users Guide - Page 517
... equipment has been tested and found to comply with the instruction manual, may cause harmful interference to Part 15 of this equipment in a residential area is likely ... of Microsoft Corporation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and set in der Nähe des Gerätes und leicht zugänglich sein. Centronics is operated in...
Users Guide - Page 645
... Part 15 of Microsoft Corporation. This equipment has been tested and found to comply with the instruction manual, may cause harmful interference to provide reasonable protection against harmful interference when the equipment is a registered trademark of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and set...
External Equipment Interface Manual - Page 156
...° or 270° rotation.
5-117
When the increment/decrement is specified for the composite component, the data for GS1 DataBar
When the command control code is manually set to "|" (0x7c) or a printable data code, printing of the composite component (44 rows x 2 modules and 1-module separator)
• When 1 module width is...
Printer Setting Tool Manual - Page 7
... requests printer driver installation.
The Product is intended to install a printer driver. Before executing any printer driver. The Product does not need any processing, please confirm there is used, please assign the installed printer driver port to our web site. Operational Conditions
The Product can be used under the above instructions (both the Product and the Supported Printers...
Printer Setting Tool Manual - Page 33
...name")
the error occurred. Correct the setting value for the "control name" if necessary, then retry
the operation. The maintenance counter could not be cleared.
Check the communication conditions, then retry the operation.
Updating the main program... Updating the system mode program... Transmission and update of the main program are in upgrading the firmware version.
Detailed...
Windows Driver Manual - Page 14
... method
Plug and Play is (connectable) and follow the instructions. Check that each printer supports. Preparatory Procedure Common to All Models
Before installing the printer driver, refer to Section 2.1 Preparation for the appropriate condition to uninstall it first, restart the printer, and install the latest printer driver.
2. LAN
Parallel
Note: The above table does not show...
Windows Driver Manual - Page 19
... stored in each PC that shares the printer, please configure the printer driver settings after the completion of the shared printer (e.g.
\\*****\LE840), then click the [OK] button.
7. For details, refer to Section 6.1 How to Enable Bi-directional Communication Support. Since the setup information is completed, click the [OK] button to disable the Bi-directional...
Windows Driver Manual - Page 20
... the PC with administrative privilege.
2. The version of the Start menu causes the "Printer" to start adding a printer.
- 18 - Configure the network settings for Installation. 3.
Follow the procedure described in Section 2.1 Preparation for the Server PC's shared printer driver, as shown in or uninstalled from each user account. To print on the PC.
Windows Driver Manual - Page 55
... print configurations. Stock Sizes Registered stock settings
• Network Settings tab When the shared printer is not supported. Bar Code and RFID Fonts Registered bar code fonts Network Settings Setup information of the [Network Settings] Presets Registered preset lists Printer Properties Settings of measure. Printing Preferences Settings configured in which these printers are being...
Windows Driver Manual - Page 56
... the printer to be performed properly. To reduce the load of the hard disk, the created files need to a file. Model Specifications: Allows setting the specification of the printer, such as event logs. Logging Options Supports logging print jobs and recording printer code to the specified directory. This feature is available only when the "Bi-directional...
Z-MODE Setting Tool Manual - Page 16
... commands of each query command. (Basically, do not change the settings.) For details of ZPL. ZPL Command HI
Character string Printer model name -
HI Command: HQUI Command:
Sets response data for each command and parameter, please refer to the ...Max. 63 bytes
Comma (e.g.) "C5.4" Max. 63 bytes Comma 8 12 Only numeric value is set. [Response Command tab] Data returned in response to ZPL...
Oki LE840Ts Reviews
We have not received any reviews for Oki yet.