Service Manual
Page 3
... must be replaced with all foreign materials. CAUTION: Please use a high impedance high voltage meter, connect (-) to chassis and (+) to the CDT anode cap. • Set the brightness control to maximum point at the factory recommended level. • If the meter indication exceeds the maximum level, immediate service is required to...
... must be replaced with all foreign materials. CAUTION: Please use a high impedance high voltage meter, connect (-) to chassis and (+) to the CDT anode cap. • Set the brightness control to maximum point at the factory recommended level. • If the meter indication exceeds the maximum level, immediate service is required to...
Service Manual
Page 5
... or exit the on screen display. 4. The Brightness and Contrast functions are also available in DPMS (Energy Saving) mode, - Press the buttons to adjust the settings and then the MENU button to turn the monitor ON or OFF. 2. MENU Button Use this button to save all changes. Brightview Button(To apply...
... or exit the on screen display. 4. The Brightness and Contrast functions are also available in DPMS (Energy Saving) mode, - Press the buttons to adjust the settings and then the MENU button to turn the monitor ON or OFF. 2. MENU Button Use this button to save all changes. Brightview Button(To apply...
Service Manual
Page 7
A(Width) : 5.0~15.0mm B(Depth) : 0.6~0.9mm C(Height) : 12.0mm C Tip AB (b) 1 3 3 2 2 -7- DISASSEMBLY 1. TILT/SWIVEL & BACK COVER REMOVAL 1) Set the monitor face downward. 2) Carefully remove the Tilt/Swivel by pulling it upward. 3) Pressing the latch (b), Back cover by pushing it upward. 4) Release the latch (c). (See Tip Spec.) 5) Slide the Back Cover away from the Front Cabinet of the monitor. Back Cover (c) Cabinet (a) Tip Spec.
A(Width) : 5.0~15.0mm B(Depth) : 0.6~0.9mm C(Height) : 12.0mm C Tip AB (b) 1 3 3 2 2 -7- DISASSEMBLY 1. TILT/SWIVEL & BACK COVER REMOVAL 1) Set the monitor face downward. 2) Carefully remove the Tilt/Swivel by pulling it upward. 3) Pressing the latch (b), Back cover by pushing it upward. 4) Release the latch (c). (See Tip Spec.) 5) Slide the Back Cover away from the Front Cabinet of the monitor. Back Cover (c) Cabinet (a) Tip Spec.
Service Manual
Page 9
... used for control of the screen brightness by supplying the saw -tooth wave to the anode, focus, and screen voltage of H and V sync. 3) The Micom sets operating mode and offers the controlled data. (H-size, H-position, V-size, ... Horizontal and Vertical Oscillation. This circuit generates the horizontal pulse and the vertical pulse by...
... used for control of the screen brightness by supplying the saw -tooth wave to the anode, focus, and screen voltage of H and V sync. 3) The Micom sets operating mode and offers the controlled data. (H-size, H-position, V-size, ... Horizontal and Vertical Oscillation. This circuit generates the horizontal pulse and the vertical pulse by...
Service Manual
Page 11
...compatible PC. 3) EEPROM → ALL CLEAR → Y(Yes) command. Luminance Meter. - But a monitor is changed. Programmable Signal Generator. (eg. Set external Brightness and Contrast volume to 0.4±0.1FL of the raster luminance. 10) Adjust repeat number 8). 11) After push the "ENTER" key. 11-1) COMMAND...DIST.ADJ→CTRL PWM → High Voltage Command. 3) Adjust High Voltage to 150(96) at Mode 1. 2) Run alignment program for T710BH on the White Balance Meter with saved each mode data. - Adjustment for Factory Mode (Preset Mode). 1) Display cross hatch pattern at DRIVE ...
...compatible PC. 3) EEPROM → ALL CLEAR → Y(Yes) command. Luminance Meter. - But a monitor is changed. Programmable Signal Generator. (eg. Set external Brightness and Contrast volume to 0.4±0.1FL of the raster luminance. 10) Adjust repeat number 8). 11) After push the "ENTER" key. 11-1) COMMAND...DIST.ADJ→CTRL PWM → High Voltage Command. 3) Adjust High Voltage to 150(96) at Mode 1. 2) Run alignment program for T710BH on the White Balance Meter with saved each mode data. - Adjustment for Factory Mode (Preset Mode). 1) Display cross hatch pattern at DRIVE ...
Service Manual
Page 12
... "EDID Write OK!!" message of monitor. 3) Exit from the alignment program. 4) Power switch OFF/ON for Focus. 1) Set the Brightness and Contrast to max position. 2) Display H character in full screen at Mode 4. 20) Set Brightness and Contrast to Max position. 21) COLOR ADJ. → LUMINANCE → ABL command. 22) Adjust ABL to...
... "EDID Write OK!!" message of monitor. 3) Exit from the alignment program. 4) Power switch OFF/ON for Focus. 1) Set the Brightness and Contrast to max position. 2) Display H character in full screen at Mode 4. 20) Set Brightness and Contrast to Max position. 21) COLOR ADJ. → LUMINANCE → ABL command. 22) Adjust ABL to...