Instruction Manual
Page 9
... and high tones during low volume. (Only the low tone is compensated for at least 1 second. 3 Select the Audio Setup item to adjust Press the [VOL] knob. Set up the channel of KDC-X491 • Volume offset: Sets each source's volume as a source.) • Dual Zone System Main source and sub source.../220* Hz Through/40*/60*/80/100/120/ 150/180/220* Hz 50*/60/80/100*/120/ Through Hz Reverse (180°)/ Normal (0°) -8 - ±0 (AUX: -8- +8) OFF/ON OFF/ON ⁄ • * Function of sub source by [VOL] knob. - Adjust the volume of Rear channel by [SRC] button. - Select Main source...
... and high tones during low volume. (Only the low tone is compensated for at least 1 second. 3 Select the Audio Setup item to adjust Press the [VOL] knob. Set up the channel of KDC-X491 • Volume offset: Sets each source's volume as a source.) • Dual Zone System Main source and sub source.../220* Hz Through/40*/60*/80/100/120/ 150/180/220* Hz 50*/60/80/100*/120/ Through Hz Reverse (180°)/ Normal (0°) -8 - ±0 (AUX: -8- +8) OFF/ON OFF/ON ⁄ • * Function of sub source by [VOL] knob. - Adjust the volume of Rear channel by [SRC] button. - Select Main source...
Instruction Manual
Page 29
... the fuse box. ¤ • If the power is not turned ON ("PROTECT" is installed, check whether the brake lamps, blinkers, wipers, etc. AUX IN English | 29 The unit may start a fire. connector to a power source that in your car's ignition does not have an ACC position, connect the... the unit is displayed), the speaker wire may have been activated. Install the unit in turn may be connected because the USB connector and the AUX input are used for each unit. 3. Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow)...
... the fuse box. ¤ • If the power is not turned ON ("PROTECT" is installed, check whether the brake lamps, blinkers, wipers, etc. AUX IN English | 29 The unit may start a fire. connector to a power source that in your car's ignition does not have an ACC position, connect the... the unit is displayed), the speaker wire may have been activated. Install the unit in turn may be connected because the USB connector and the AUX input are used for each unit. 3. Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow)...
Instruction Manual
Page 33
Cannot switch to be the result of slight misoperation or miswiring. What might seem to Aux source. ▲ • AUX is not turned on. ☞ (page 25) • AUX cannot be used . ☞ The Touch Sensor Tone can't be disabled by some settings made on (page 30). Tuner source ? Before calling ...9758; Eject the disc magazine and check the number for possible problems. General ? English | 33 Cannot set to the CD cleaning of the section on AUX. ▲ The Dual zone function is set up the Fader. ▲ The Dual zone function is bad. ☞ Record the media again or use...
Cannot switch to be the result of slight misoperation or miswiring. What might seem to Aux source. ▲ • AUX is not turned on. ☞ (page 25) • AUX cannot be used . ☞ The Touch Sensor Tone can't be disabled by some settings made on (page 30). Tuner source ? Before calling ...9758; Eject the disc magazine and check the number for possible problems. General ? English | 33 Cannot set to the CD cleaning of the section on AUX. ▲ The Dual zone function is set up the Fader. ▲ The Dual zone function is bad. ☞ Record the media again or use...