Owner's Manual
Page 7
... Light Socket (2) Motor Assembly Cover Motor Drive Board Controller Board # 10-24 x 3/8" Hex Head # 8-32 x 1" Phillips Screw # 8-32 x 3/8" Slotted Hex Head Screw Power Cord For Help, call 1-800-35-GENIE or visit www.geniecompany.com 7 Parts ...only Emergency Release Knob (green bag) 1 1 Emergency Release Tag (carriage) 1 1 Header Bracket (orange bag) 1 1 Door Bracket (orange bag) varies1/m ode l 1 1/4" x 2" Lag Screw (orange bag) 8 Straight Door Arm (main carton) 1 1 Clevis Pin, 3/8" x 15/16" (yellow bag) 2 2 Cotter Pin, .073" dia. (yellow bag) 2 2 Curved...
... Light Socket (2) Motor Assembly Cover Motor Drive Board Controller Board # 10-24 x 3/8" Hex Head # 8-32 x 1" Phillips Screw # 8-32 x 3/8" Slotted Hex Head Screw Power Cord For Help, call 1-800-35-GENIE or visit www.geniecompany.com 7 Parts ...only Emergency Release Knob (green bag) 1 1 Emergency Release Tag (carriage) 1 1 Header Bracket (orange bag) 1 1 Door Bracket (orange bag) varies1/m ode l 1 1/4" x 2" Lag Screw (orange bag) 8 Straight Door Arm (main carton) 1 1 Clevis Pin, 3/8" x 15/16" (yellow bag) 2 2 Cotter Pin, .073" dia. (yellow bag) 2 2 Curved...
Owner's Manual
Page 9
...on Motor Shaft (Figure 9). B Install Coupler on collar 11B. Keep Rail Sections level until later. (Middle Rail Section looks the same on Drive Screw next to Collar (Figure11D). Finger-tighten until the Opener is needed, attach it per instructions supplied with 2 (1/4"-20) (yellow) Hex Head Shoulder...Arrange arrows on Retaining Clip Figure 11 Attach Middle Rail Section For Help, call 1-800-35-GENIE or visit www.geniecompany.com 9 Snap on Rail Sections to point in step A & B. CAUTION The Drive Screw and Rail Liner can slide out of Rail Sections. Connect with kit. 11A.
...on Motor Shaft (Figure 9). B Install Coupler on collar 11B. Keep Rail Sections level until later. (Middle Rail Section looks the same on Drive Screw next to Collar (Figure11D). Finger-tighten until the Opener is needed, attach it per instructions supplied with 2 (1/4"-20) (yellow) Hex Head Shoulder...Arrange arrows on Retaining Clip Figure 11 Attach Middle Rail Section For Help, call 1-800-35-GENIE or visit www.geniecompany.com 9 Snap on Rail Sections to point in step A & B. CAUTION The Drive Screw and Rail Liner can slide out of Rail Sections. Connect with kit. 11A.
Owner's Manual
Page 23
..., the door should stay open. Operation is acceptable. For Help, call Customer Service at 1-800-35-GENIE. • Balance Door. Release Magnetic Carriage Assembly from Drive Screw. • Lubricate Drive Screw with Part 15 of Motor Cover MAINTENANCE A Monthly Door springs and door hardware: - B Install Lens into...See Check Step 2 on page 21. NOTE When the door is now complete. If the Opener still fails, contact a Genie Factory Authorized Dealer for service or call Customer Service at that may cause undesired operation. GLU-3 Lubricant FCC AND IC CERTIFIED All...
..., the door should stay open. Operation is acceptable. For Help, call Customer Service at 1-800-35-GENIE. • Balance Door. Release Magnetic Carriage Assembly from Drive Screw. • Lubricate Drive Screw with Part 15 of Motor Cover MAINTENANCE A Monthly Door springs and door hardware: - B Install Lens into...See Check Step 2 on page 21. NOTE When the door is now complete. If the Opener still fails, contact a Genie Factory Authorized Dealer for service or call Customer Service at that may cause undesired operation. GLU-3 Lubricant FCC AND IC CERTIFIED All...
Owner's Manual
Page 26
...Switch for a short circuit and for proper wiring. B. Check condition (not cracked, split, or broken) and placement of Rail Drive Screw are turning when Motor runs. If Opener is connected to a wiring box: • Check that all Remote Control codes from Remote...for service, or contact Customer Service at Wall Console Terminals, tighten any loose connection. • Check connections at 1-800-35-GENIE. Check Force adjustment (see Set Limit Switches and Force Controls on page 18). General Troubleshooting (Always Check the Status LED Light...
...Switch for a short circuit and for proper wiring. B. Check condition (not cracked, split, or broken) and placement of Rail Drive Screw are turning when Motor runs. If Opener is connected to a wiring box: • Check that all Remote Control codes from Remote...for service, or contact Customer Service at Wall Console Terminals, tighten any loose connection. • Check connections at 1-800-35-GENIE. Check Force adjustment (see Set Limit Switches and Force Controls on page 18). General Troubleshooting (Always Check the Status LED Light...