Epson ActionPrinter 4000 - ActionPrinter-4000 Impact Printer Support and Manuals
Get Help and Manuals for this Epson item
View All Support Options Below
Free Epson ActionPrinter 4000 manuals!
Problems with Epson ActionPrinter 4000?
Ask a Question
Free Epson ActionPrinter 4000 manuals!
Problems with Epson ActionPrinter 4000?
Ask a Question
Popular Epson ActionPrinter 4000 Manual Pages
Product Support Bulletin(s) - Page 3
The printer's internal program could not be set incorrectly.
1 beep:
BEL code
5 beeps:
Abnormal voltage-
5 beeps:
Abnormal carriage movement (.5 sec. pause between beeps)
LQ-2500 LCD Codes:
00
Invalid ID request to troubleshoot problems.
A blank LCD screen with the Power-on LED lit can be caused by a bent pin on one of problems. The following messages will help...
Product Support Bulletin(s) - Page 4
... 'Verify After Write" check to ensure proper paper handling and prevent paper jams, which can result in the Service Manual (page A-54, figure A-52) and on . Errors 0,2, 3, 10, and 20 may require a repair, adjustment or replacement. Friction/Tractor feed switching error d. Physical obstruction such as a jammed ribbon
11 Skewed paper detect error.
Platen gap motor HP not detected correctly...
User Manual - Page 34
... time you pressed the
ON LINE button. Setting Up the Printer 1-21 If paper is printed. The test did not print when you are turning on the printer. Solution
The ribbon may be installed properly. Try the self test again. Replace the ribbon cartridge.
Turn off the printer. Testing the Printer
Checking the Operation If the self test...
User Manual - Page 47
Paper Handling 2-9
CAUTION: Make sure that your paper has a clean, straight edge before inserting it into the printer. Open both sprocket covers.
0t. Using Continuous Paper 5. Move the paper support midway between the two sprocket
units.
6.
User Manual - Page 55
... Before switching to continuous paper, make sure that the single sheet is ejected and the printer is also easy to switch back to Continuous Paper It is off line. 1. Lower the paper guide onto the printer. Switching Between Continuous and Single Sheets
Switching Back to printing with
continuous paper feeding.
2.
Slide the edge guides apart so they do...
User Manual - Page 59
Printing on Special Paper To change the paper thickness setting, follow these steps. 1. Allow it to the middle of the printer.
Then remove the printer
cover.
Slide the print head to cool before touching it. 2. bl WARNING: If the printer has just been in use, the print head may be hot. Make sure that the printer is turned off. Paper Handling 2-21
User Manual - Page 62
... load multi-part paper the same way as single sheets because labels on a shiny backing sheet almost always slip a little.
2-24 Paper Handling Do not try to print labels, always use with a tractor. Printing on Special Paper Except for use labels mounted on a continuous backing sheet with sprocket holes for the paper thickness lever setting, you...
User Manual - Page 127
Using the Printer Options 5-5 Paper Handling 1.
Turn on .
7. Turn on the cut sheet feeder mode is turned on with DIP
switch 1-8 and turn on the printer. Make sure that the cut sheet feeder mode by setting DIP switch 1-8 to
on the printer. The Cut Sheet Feeder 6.
User Manual - Page 133
... especially useful because it allows you turn on the printer and make sure that the ON LINE light is discarded.
Paper out condition When the printer is sent to a different type or size of paper (for one sheet only) without replacing the stack of paper loads automatically whenever a printable character or line feed command is on...
User Manual - Page 138
Replace the clear plastic part of the cut sheet feeder mode). 4. Removal of the printer cover with the clear
plastic part that was on it originally. Set DIP switch 1-8 to off (to store the removed cut sheet feeder in its original box and packing materials.
5-16 Using the Printer Options Be sure to turn off the cut sheet feeder is now completed. The Cut Sheet Feeder 3.
User Manual - Page 185
... 255 KIDTH "LPT1" 255 If the printer still does not print properly, set by your application program to change the margin. Auto line feed may be correct. Use your application software and adjust it. Troubleshooting 7-11 Use micro-adjustment to the maximum setting using ESC Q. See Chapter 9. Printing
Problem
The print position is not what...
User Manual - Page 193
... the upright position. See Chapter 8.
See Chapter 2. See Chapter 2. Your printer can act as a paper separator. For printing on continuous multi-part forms consisting of your application program settings. The paper feed is in the lowered position so that are within the specified range. Problem
Continuous paper does not feed properly (continued). Regular gaps occur in place...
User Manual - Page 207
... with the wrong specification. Make sure that you expected (continued). The DIP switches or jumpers on the printer; The interface settings on the computer may be installed on the interface board may be set wrong. Troubleshooting 7-33 The computer and interface settings may be attached at any time. See your computer manual for the correct settings. Two cables may...
User Manual - Page 275
... both a control code and a panel button that advances the paper to begin most application software for Printers. interface The means...Epson printers and supported by most printer commands. font A font is a style of your computer. input buffer The memory in the printer in which data sent from your printer from the computer is italicized.
4 Glossary ESC (escape) code A special control code...
User Manual - Page 283
... cover, 1-12 Printer stand, 1-5 Print head, 1-8, 4-10 -12 Printing direction, 3-9 Problems, see Troubleshooting Proportional spacing, 4-2, -3,
4-6, -8, 9-25, A-2 -5 Pull tractor, 5-17, -27
installing, 5-17, -18 loading paper, 5-19, -23 removing, 5-24, -27 Push tractor, 2-6, -18
R
Ready light, 3-2 Ribbon cartridge
installing, 1-7 -9 replacing, 6-4 -9 specifications, 8-7 Roman font, 3-18
S
Sans...
Epson ActionPrinter 4000 Reviews
We have not received any reviews for Epson yet.